Oxidation of 4-Chloroaniline Studied by On-Line Electrochemistry Electrospray Ionization Mass Spectrometry

Diamond nanowires: a novel platform for electrochemistry and matrix-free mass spectrometry

Over the last decades, carbon-based nanostructures have generated a huge interest from both fundamental and technological viewpoints owing to their physicochemical characteristics, markedly different from their corresponding bulk states. Among these nanostructured materials, carbon nanotubes (CNTs), and more recently graphene and its derivatives, hold a central position. The large amount of work devoted to these materials is driven not only by their unique mechanical and electrical properties, but also by the advances made in synthetic methods to produce these materials in large quantities with reasonably controllable morphologies. While much less studied than CNTs and graphene, diamond nanowires, the diamond analogue of CNTs, hold promise for several important applications. Diamond nanowires display several advantages such as chemical inertness, high mechanical strength, high thermal and electrical conductivity, together with proven biocompatibility and existence of various strategies to functionalize their surface. The unique physicochemical properties of diamond nanowires have generated wide interest for their use as fillers in nanocomposites, as light detectors and emitters, as substrates for nanoelectronic devices, as tips for scanning probe microscopy as well as for sensing applications. In the past few years, studies on boron-doped diamond nanowires (BDD NWs) focused on increasing their electrochemical active surface area to achieve higher sensitivity and selectivity compared to planar diamond interfaces. The first part of the present review article will cover the promising applications of BDD NWS for label-free sensing. Then, the potential use of diamond nanowires as inorganic substrates for matrix-free laser desorption/ionization mass spectrometry, a powerful label-free approach for quantification and identification of small compounds, will be discussed.

Perspective on electrospray ionization and its relation to electrochemistry

The phenomenon of electrospraying of liquids is presented from the perspective of the electrochemistry involved. Basics of current and liquid flow in the capillary and spray tip are discussed, followed by specifics of charging and discharging of the sprayed liquid surface. Fundamental theories and numerical modeling relating electrospray current to solution and spray parameters are described and then compared with our own experimentally obtained data. The method of mapping potentials and currents inside the electrospray capillary by using an inserted electrically-isolated small wire probe electrode is discussed in detail with illustrations from new and published data. Based on these experimentally obtained results, a new mathematical model is derived. The introduced "nonlinear resistor electrospray capillary model" divides the electrospray capillary into small sections, adds their contributions, and then, by transition to infinitely small section thickness, produces analytical formulas that relate current and potential maps to other properties of the electrospraying liquid: primarily conductivity and current density. The presentation of the model is undertaken from an elementary standpoint, and it offers the possibility to obtain quantitative information regarding operating parameters from typical analytical systems subjected to electrospray. The model stresses simplicity and ease of use; examples applying experimental data are shown and some predictions of the model are also presented. The developed nonlinear resistor electrospray capillary model is intended to provide a new quantitative basis for improving the understanding of electrochemical transformations occurring in the electrospray emitter. A supplemental material section gives full derivation of the model and discusses other consequences.

Mass spectrometric methods for monitoring redox processes in electrochemical cells

Electrochemistry (EC) is a mature scientific discipline aimed to study the movement of electrons in an oxidation-reduction reaction. EC covers techniques that use a measurement of potential, charge, or current to determine the concentration or the chemical reactivity of analytes. The electrical signal is directly converted into chemical information. For in-depth characterization of complex electrochemical reactions involving the formation of diverse intermediates, products and byproducts, EC is usually combined with other analytical techniques, and particularly the hyphenation of EC with mass spectrometry (MS) has found broad applicability. The analysis of gases and volatile intermediates and products formed at electrode surfaces is enabled by differential electrochemical mass spectrometry (DEMS). In DEMS an electrochemical cell is sampled with a membrane interface for electron ionization (EI)-MS. The chemical space amenable to EC/MS (i.e., bioorganic molecules including proteins, peptides, nucleic acids, and drugs) was significantly increased by employing electrospray ionization (ESI)-MS. In the simplest setup, the EC of the ESI process is used to analytical advantage. A limitation of this approach is, however, its inability to precisely control the electrochemical potential at the emitter electrode. Thus, particularly for studying mechanistic aspects of electrochemical processes, the hyphenation of discrete electrochemical cells with ESI-MS was found to be more appropriate. The analytical power of EC/ESI-MS can further be increased by integrating liquid chromatography (LC) as an additional dimension of separation. Chromatographic separation was found to be particularly useful to reduce the complexity of the sample submitted either to the EC cell or to ESI-MS. Thus, both EC/LC/ESI-MS and LC/EC/ESI-MS are common.

Complete quantitative online analysis of methanol electrooxidation products via electron impact and electrospray ionization mass spectrometry

We report on a novel approach for complete quantitative online product analysis in electrocatalytic reactions, combining electron impact ionization mass spectrometry (EI-MS) and electrospray ionization mass spectrometry (ESI-MS) for simultaneous detection of both volatile and nonvolatile reaction products. The potential of this method is demonstrated using continuous methanol oxidation in a flow cell. The overall reaction rate was followed via the Faradaic current; CO(2) formation was monitored mass spectrometrically via a membrane inlet system, and formaldehyde and formic acid were detected by ESI-MS after a derivatization-extraction-separation procedure introduced recently (Zhao, W.; Jusys, Z.; Behm, R. J. Anal. Chem.2010, 82, 2472-2479) providing quantitative data on the product distribution. In a more general sense, this approach is applicable for a wide range of reactions at the solid-liquid interface or in liquid phase.

Label-free sensing of pH and silver nanoparticles using an "OR" logic gate

Many natural phenomena are associated with the presence of two or more separate variables. We report here an "OR" DNA logic gate based on a luminescent platinum(II) switch-on probe for silver nanoparticles and pH, both of which may be considered putative indicators of pollution. The modulation of metal complex/double-stranded DNA complex phosphorescence by Ag(+) and H(+) was used to construct a simple, rapid and label-free method for the label-free detection of pH and nanomolar Ag(+) ions and nanoparticles in aqueous solutions with high selectivity.

Electrochemical simulation of oxidation processes involving nucleic acids monitored with electrospray ionization-mass spectrometry

Oxidation is commonly involved in the alteration of nucleic acids giving rise to diverse effects including mutation, cell death, malignancy, and aging. We demonstrate that electrochemistry represents an efficient and fast method to mimic oxidative modification of nucleic acids occurring in biological systems. Oxidation reactions were performed in a thin-layer cell employing a conductive diamond electrode as the working electrode and were monitored with electrospray ionization-mass spectrometry. Mass voltammograms were acquired for guanosine, adenosine, cytidine, and uridine. The observed oxidation potentials increased in the order guanosine << adenosine < cytidine < uridine. Oxidation products of guanosine were characterized using high-resolution (tandem) mass spectrometry performed with a quadrupole-quadrupole time-of-flight instrument. On the basis of these experiments, it was concluded that the initial electrode reaction involves a one-electron, one-proton step to give a free radical. The primary oxidation product represents the starting point for a number of follow-up reactions, including guanosine dimerization as well as further oxidation to 8-hydroxyguanosine. Similar results were obtained for guanosine monophosphate and the corresponding dinucleotide. Furthermore, the guanosine radical was identified as an important intermediate for the formation of a covalent adduct with acetaminophen. This observation sheds new light on the mechanism of adduct formation as it demonstrates that oxidative activation of both the nucleobase and the adduct-forming agent is necessary to observe a detectable amount of adduct species.

Quantitative online analysis of liquid-phase products of methanol oxidation in aqueous sulfuric acid solutions using electrospray ionization mass spectrometry

We describe a novel method and setup for quantitative online analysis of the liquid-phase methanol oxidation products in acidic aqueous solutions by electrospray ionization mass spectrometry (ESI-MS). This includes a specially designed flow system, which allows continuous online mixing, derivatization, extraction, separation, and quantitative detection within ca. 3 min. For electrospray ionization of formaldehyde, it is first online-derivatized by 2,4-dinitrophenyl hydrazine to form the easily ionizable 2,4-dinitrophenyl hydrazone. Then, both formic acid and derivatized formaldehyde are online extracted into an immiscible organic phase, which, after separation from the aqueous phase, is piped to the ESI-MS for analysis. This strategy ensures complete removal of the highly corrosive sulfuric acid from the analyte and allows the liquid-phase methanol oxidation reaction (MOR) products (formaldehyde and formic acid) to be quantitatively detected by ESI-MS. Finally, the potential of this method for online analysis in electroanalysis and electrocatalysis is discussed.