Influences of Temperature and Metal on Subcritical Hydrothermal Liquefaction of Hyperaccumulator: Implications for the Recycling of Hazardous Hyperaccumulators

Speciation, leachability, and phytoaccessibility of heavy metals during thermochemical liquefaction of contaminated peanut straw

In this study, the speciation, leachability, phytoaccessibility, and environmental risks of heavy metals (Cd, Zn, and Cu) during liquefaction of contaminated peanut straw in ethanol at different temperatures (220, 260, 300, 340, and 380 °C) were comprehensively investigated. The results showed that elevated temperatures facilitated heavy metal accumulation in the biochar. The acid-soluble/exchangeable and reducible fraction percentages of heavy metals were substantially reduced in the biochar after liquefaction as the temperature increased, and the oxidizable fraction became the dominant heavy metal fraction, accounting for 44.14-78.67%. Furthermore, although an excessively high liquefaction temperature (380 °C) increased the residual fraction percentages of Zn and Cu, it was detrimental to Cd immobilization. The acid-soluble/exchangeable Cd in the contaminated peanut straw readily migrates to the bio-oil during liquefaction, with the highest concentration of 1.60 mg/kg at 260 °C liquefaction temperature, whereas Zn and Cu are predominantly bound to the unexchangeable fraction in the bio-oil. Liquefaction inhibited heavy metal leachability and phytoaccessibility in biochar, the lowest extraction rates of Cd, Zn, and Cu were 0.71%, 1.66% and 0.95% by diethylenetriamine pentaacetic acid, respectively. However, the leaching and extraction concentrations increased when the temperature was raised to 380 °C. Additionally, heavy metal risk was reduced from medium and high risk to no and low risk. In summary, liquefaction reduces heavy metal toxicity and the risks associated with contaminated peanut straw, and a temperature range of 300-340 °C for ethanol liquefaction can be considered optimal for stabilizing heavy metals.

A review on the thermochemical treatments of biomass: Implications for hydrochar production and rare earth element recovery from hyperaccumulators

Phytomining is a promising method that employs hyperaccumulators to concentrate metals from various substrates. Many studies on phytomining have been reported in the literature, while how to recover metals from hyperaccumulators has not been well resolved, which is critical for developing a complete phytomining-based metal recovery process. The most straightforward approach is to combust hyperaccumulators and recover metals from the combustion residue. However, the combustion process results in significant waste and carbon emissions. In contrast to combustion, thermochemical treatments can convert the biomass of hyperaccumulators to valuable products, such as biochar, hydrochar, biocrudes, and biogas. Therefore, it is more sustainable to develop a process that combines thermochemical treatments for metal recovery from hyperaccumulators. To achieve this objective, a systematic and comprehensive understanding of product characteristics and metal fate during thermochemical processing is required. In this article, three emerging thermochemical technologies, i.e., microwave-assisted pyrolysis, hydrothermal processing, and microwave-assisted hydrothermal treatment, are systematically reviewed in terms of conversion mechanisms, merits, demerits, product characteristics, and metal fate. Significant findings reported in the literature on the effects of operating parameters on product characteristics and metal fate during thermochemical treatment of waste biomass, especially those from hyperaccumulators, were summarized. Due to limited studies on thermochemical treatments of rare earth element hyperaccumulators, this review is expanded to include hyperaccumulators of any metal species. Based on comparisons among the three emerging thermochemical treatment technologies, microwave-assisted hydrothermal pyrolysis is identified as the most promising approach that favors carbon product obtainment and REE recovery from hyperaccumulators.

Roles and significance of chelating agents for potentially toxic elements (PTEs) phytoremediation in soil: A review

Phytoremediation is a biological remediation technique known for low-cost technology and environmentally friendly approach, which employs plants to extract, stabilise, and transform various compounds, such as potentially toxic elements (PTEs), in the soil or water. Recent developments in utilising chelating agents soil remediation have led to a renewed interest in chelate-induced phytoremediation. This review article summarises the roles of various chelating agents and the mechanisms of chelate-induced phytoremediation. This paper also discusses the recent findings on the impacts of chelating agents on PTEs uptake and plant growth and development in phytoremediation. It was found that the chelating agents have increased the rate of metal absorption and translocation up to 45% from roots to the aboveground plant parts during PTEs phytoremediation. Besides, it was also explored that the plants may experience some phytotoxicity after adding chelating agents to the soil. However, due to the leaching potential of synthetic chelating agents, the use of organic chelants have been explored to be used in PTEs phytoremediation. Finally, this paper also presents comprehensive insights on the significance of using chelating agents through SWOT analysis to discuss the advantages and limitations of chelate-induced phytoremediation.

Phytoremediation of toxic chemicals in aquatic environment with special emphasis on duckweed mediated approaches

The discharge of toxic chemicals into water bodies and their linked detrimental effects on health is a global concern. Phytoremediation, an environment-friendly plant-based technology, has gained intensive interest over the last decades. For the aquatic phytoremediation process, the commonly available duckweeds have recently attracted significant attention due to their capacity to grow in diverse ecological niches, fast growth characteristics, suitable morphology for easy handling of biomass, and capacity to remove and detoxify various potential toxic elements and compounds. This review presents the progress of duckweed-assisted aquatic phytoremediation of toxic chemicals. A brief background of general phytoremediation processes, including the different phytoremediation methods and advances in understanding their underlying mechanisms, has been described. A summary of different approaches commonly practiced to assess the growth of the plants and their metal removal capacity in the phytoremediation process has also been included. A vast majority of studies have established that duckweed is an efficient plant catalyst to accumulate toxic heavy metals and organic contaminants, such as pesticides, fluorides, toxins, and aromatic compounds, reducing their toxicity from water bodies. The potential of this plant-based phytoremediation process for its downstream applications in generating value-added products for the rural economy and industrial interest has been identified.

Challenges and opportunities for improving the environmental quality of cadmium-contaminated soil in China

Considering the soil cadmium pollution problem, the Chinese government proposed to estimate the costs and practicality "to completely improve the soil quality by the middle of this century". This study analyzed the challenges in achieving this goal using biophysical data from 10 typical demonstration soil phytoextraction projects. The current annual phytoextraction efficiency was determined as 14.8-490 g ha^-1 a^-1 at 319 RMB g^-1 cadmium. A total of 798 billion RMB and 5 years were required for remediation of cadmium contamination, which was 22 times the investment in soil remediation during 2016-2022. The break-even point of phytoextraction projects was 29 years. The heavy financial burden was considered the primary challenge in improving the environmental quality of such soil. The cost could be reduced by 5.5-35.3 % through optimization measures such as resourcefulness of hyperaccumulator harvests, large-scale breeding, and mechanized management. The break-even point could be shortened to 6-15 years by intercropping/rotating crops, contributing to the goal. Active exploration of phytoextraction efficiency-more efficient accumulators, optimized agronomic measures-is worth practicing.

Selective recovery of rare earth elements and value-added chemicals from the Dicranopteris linearis bio-ore produced by agromining using green fractionation

The increasing demand for Rare Earth Elements (REEs) and the depletion of mineral resources motivate sustainable strategies for REE recovery from alternative unconventional sources, such as REE hyperaccumulator. The greatest impediment to REE agromining is the difficulty in the separation of REEs and other elements from the harvested biomass (bio-ore). Here, we develop a sulfuric acid assisted ethanol fractionation method for processing D. linearis bio-ore to produce the pure REE compounds and value-added chemicals. The results show that 94.5% of REEs and 87.4% of Ca remained in the solid phase, and most of the impurities (Al, Fe, Mg, and Mn) transferred to the liquid phase. Density functional theory calculations show that the water-cation bonds of REEs and Ca cations were broken more easily than the bonds of the cations of key impurities, causing lower solubility of REEs and Ca compounds. Subsequent separation and purification led to a REE-oxide (REO) product with a purity of 97.1% and a final recovery of 88.9%. In addition, lignin and phenols were obtained during organosolv fractionation coupled with a fast pyrolysis process. This new approach opens up the possibility for simultaneous selective recovery of REEs and to produce value-added chemicals from REE bio-ore refining.

Effects of microwave and plastic content on the sulfur migration during co-pyrolysis of biomass and plastic

In order to reduce the risks of sulfur-containing contaminants present in biofuels, the effects of microwave and content of hydrogen donor on the cracking of C-S bonds and the migration of sulfur were studied by co-pyrolysis of biomass and plastic. The synergistic mechanism of microwave and hydrogen donor was explored from the perspective of deducing the evolution of sulfur-containing compounds based on microwave thermogravimetric analysis. By combining temperature-weight curves, it was found that microwaves and hydrogen radicals promoted the cracking of sulfur-containing compounds and increased the mass loss of biomass during pyrolysis. The mixing ratio of hydrogen donor (plastic) was the key parameter resulting in the removal of sulfur from oil. By adjusting the mixing ratio, the yield of co-pyrolyzed oil was three times higher than that of cow dung pyrolysis alone and the relative removal rate of sulfur reached 73.67%. The relative content of sulfur in the oil was reduced by 73.77% due to the escape of sulfur-containing gases (H₂S, COS and C₂H₅SH) and the formation of sulfate crystals in the char. Microwave selectively heated sulfur-containing organics and hydrogen radicals stimulated the breaking of C-S bonds, which improved the cracking efficiency of the oil. This breaking will provide a theoretical and technological reference for the environmentally friendly treatment of biomass and biofuels.

Promising strategies of circular bioeconomy using heavy metal phytoremediated plants - A critical review

Phytoremediation is an excellent method for removing harmful heavy metals from the environment since it is eco-friendly, uses little energy, and is inexpensive. However, as phytoremediated plants can turn into secondary sources for heavy metals, complete heavy metal removal from phytoremediated plants is necessary. Elimination of toxic heavy metals from phytoremediated plants should be considered with foremost care. This review highlights about important sources of heavy metal contamination, health effects caused by heavy metal contamination and technological breakthroughs of phytoremediation. This review critically emphasis about promising strategies to be engaged for absolute reutilization of heavy metals and spectacular approaches of production of commercially imperative products from phytoremediated plants through circular bioeconomy with key barriers. Thus, phytoremediation combined with circular bioeconomy can create a new platform for the eco-friendly life.

Efficient Removal of Heavy Metals from Contaminated Sunflower Straw by an Acid-Assisted Hydrothermal Process

The removal of heavy metals is crucial to the utilization of contaminated biomass resources. In this study, we report an efficient process of hydrothermal conversion (HTC) of sunflower straw (Helianthus annuus L.) to remove heavy metals. The effect of different HTC temperatures and concentrations of HCl additives on heavy metal removal efficiency was investigated. The results revealed that increasing the temperature or concentration of HCl promoted the transfer of heavy metals from hydrochar to liquid products during HTC. The heavy metals removed to the liquid products included up to 99% of Zn and Cd, 94% of Cu, and 87% of Pb after hydrothermal conversion with a temperature of 200 °C and HCl 2%. The species of heavy metals in hydrochars converted from unstable to stable with an increase in temperature from 160 °C to 280 °C. The stable fractions of heavy metals in the acidic condition decreased as the acid concentration increased. This aligns well with the high transfer efficiency of heavy metals from the solid phase to the liquid phase under acidic conditions. The FTIR indicated that the carboxy and hydroxy groups decreased significantly as the temperature increased and the concentration of HCl increased, which promoted the degradation of sunflower straw. A scan electron microscope showed that the deepening of the destruction of the initial microstructure promotes the transfer of heavy metals from hydrochars to liquid phase products. This acid-assisted hydrothermal process is an efficient method to treat biomass containing heavy metals.

Thermochemical conversion of heavy metal contaminated biomass: Fate of the metals and their impact on products

With the rapid depletion of fossil energy and increasingly severe environmental pollution, the development of biomass resources for biorefineries has become a new research focus. However, heavy metals may be released during the thermochemical treatment when the biomass materials used in biomass conversion are contaminated by heavy metals. This can cause secondary environmental pollution or transference to the target products, reducing product quality. Therefore, having a systematic understanding of the fate of heavy metals in biomass conversion is necessary for alleviating potential risks. This study presents the current status of contaminated biomass and conversion products involving thermochemical processes, the migration, transformation, and impact of heavy metals in biomass conversion was investigated, and the utilization of heavy metals in contaminated biomass was briefly outlined. This review aims to link biomass conversion to the fate of heavy metals, avoid existing risks as much as possible to produce cleaner products efficiently, and promote the sustainable development of heavy metal contaminated biomass resources.

Emerging disposal technologies of harmful phytoextraction biomass (HPB) containing heavy metals: A review

Phytoextraction is an effective approach for remediation of heavy metal (HM) contaminated soil. After the enhancement of phytoextraction efficiency has been systematically investigated and illustrated, the harmless disposal and value-added use of harmful phytoextraction biomass (HPB) become the major issue to be addressed. Therefore, in recent years, a large number of studies have focused on the disposal technologies for HPB, such as composting, enzyme hydrolysis, hydrothermal conversion, phyto-mining, and pyrolysis. The present review introduces their operation process, reaction parameters, economic/ecological advantages, and especially the migration and transformation behavior of HMs/biomass. Since plenty of plants possess comparable extraction abilities for HMs but with discrepancy constitution of biomass, the phytoextraction process should be combined with the disposal of HPB after harvested in the future, and thus a grading handling strategy for HPB is also presented. Hence, this review is significative for disposing of HPB and popularizing phytoextraction technologies.

Integrated glycolysis and pyrolysis process for multiple utilization and cadmium collection of hyperaccumulator Sedum alfredii

Phytoremediation is a cost-effective and environmentally-friendly method to treat cadmium (Cd) contaminated soils, however, there is still a lack of safe disposal methods of harvested hyperaccumulators. In this study, by integrating glycolysis and pyrolysis, we investigated the possibility of bioproduct production and Cd collection from the hyperaccumulator Sedum alfredii. By means of acid-alkali pretreatment, the degree of cellulose polymerization was reduced by 36.24% while the surface accessibility was increased by 115.80%, resulting in a bioethanol yield of 9.29%. Meanwhile, 99.22% of total Cd of biomass could be reclaimed by collecting H₂SO₄-pretreatment waste. The saccharification residue was subsequently modified by NaOH-pretreatment-filtrate and converted into biochar at 500 °C which possessed a maximum Cd²⁺ sorption capacity of 60.52 mg g^-1 based on the Langmuir model. Furthermore, sustainability analysis indicated that the economic input of this process is acceptable when considering its good environmental benefits. Taken together, our study provides a strategy for simultaneous bioethanol and biochar production during Cd collection from the hyperaccumulator S. alfredii, which could be a promising alternative for the suitable treatment of metal-enriched plants.

A review on disposal and utilization of phytoremediation plants containing heavy metals

The reasonable disposal of plant biomass containing heavy metals (HMs) is a difficult problem for the phytoremediation technology. This review summarizes current literature that introduces various disposal and utilization methods (heat treatment, extraction treatment, microbial treatment, compression landfill, and synthesis of nanomaterials) for phytoremediation plants with HMs. The operation process and technical parameters of each disposal method are different. HMs can migrate and transform in different disposal processes. Some disposal and utilization methods can get some by-products. The main purpose of this paper is to provide reference for technical parameters and characteristics of various disposal and utilization methods, so as to choose and use the appropriate method for the treatment of plant biomass containing HMs after phytoremediation.

Migration and transformation of heavy metals in hyperaccumulators during the thermal treatment: a review

The pollution of heavy metals (HMs) in the soil has become one of the important factors affecting the national environment and human health. Phytoremediation, as a technology to deal with HM pollution in soil, has been extensively studied and applied due to its sustainability and environmental friendliness. However, hyperaccumulators polluted by HMs need to be properly treated to avoid secondary pollution to the environment. This paper reviews the migration and transformation of HMs during the incineration, pyrolysis, gasification, and hydrothermal treatment of hyperaccumulators; comprehensively evaluates the advantages and disadvantages of each technology in the treatment of HM-enriched hyperaccumulators; and analyzes the current development status and unsolved problems in detail for each technology. Generally speaking, thermal treatment technology can fix most of the HMs of exchangeable fraction in biochar, reducing its bioavailability and biotoxicity. In addition, the application direction and research focus of the target product are discussed, and it is clarified that in the future, it is necessary to further optimize the reaction conditions and explore the mechanism of HM immobilization to maximize the immobilization of HMs and improve the quality and output of the target product.

Dispose waste liquor of fresh biomass of a hyperaccumulator Sedum plumbizincicola in phytoextraction process

Sedum plumbizincicola has been widely employed to remove cadmium (Cd) and zinc (Zn) from contaminated soils and harvested biomass is used to recover valuable metals. While chopping and compacting are efficient methods to rapidly reduce the volume and moisture of fresh biomass, the resulting waste liquor containing metals needs treatment. Two types of contaminated soils were cropped with S. plumbizincicola and top-dressed with this liquor to study metals migration in soil profile and their uptake by plants. There were three treatments: planting and adding liquor (PL), planting without liquor (P) and adding liquor without planting (L). The results showed that Cd and Zn from liquor were mainly retained at top soil 0-10 cm under L treatment. Compared with L treatment, soil Cd and Zn under PL treatment decreased significantly in soil profile due to the extraction of S. plumbizincicola. Moreover, the amount of Cd and Zn extracted by plants was greater than that applied in soils. The metal removal rate by S. plumbizincicola in acid clay loam soil was higher than that in neutral sandy soil. To sum up, metal retaining in soil and uptake by S. plumbizincicola can be used to treat waste liquor from its fresh biomass. Novelty StatementRapid and efficient treatment of harvested fresh biomass is still a challenge although phytoextraction using hyperaccumulator Sedum plumbizincicola has been widely employed. Chopping and compacting fresh biomass are efficient methods for rapid dehydration, however, a large amount of waste liquor that contains of Cd and Zn is produced and needs treatment. In the present study, a simple and low-cost method was tested to dispose the liquor, i. e. irrigating it onto the surface of contaminated soils where grown S. plumbizincicola. It was found that Cd and Zn applied in soils from liquor were mainly retained at top 0-10 cm soil depth where S. plumbizincicola root system was widespread, and the amount of Cd and Zn extracted by plants was greater than that applied in soils. Therefore, it is technically feasible to dispose the waste liquor dewatering from fresh biomass of S. plumbizincicola in its phytoextraction process. This study is helpful for the rapid, efficient and low-cost treatment of harvested fresh biomass in the large-scale application of phytoremediation.

In Situ hydrochar regulates Cu fate and speciation: Insights into transformation mechanism

Cu is one of the dominant heavy metals toxic to human health and environmental ecosystems. Understanding its fate and chemical speciation is of great importance for hydrothermal liquefaction (HTL) of Cu-rich hazardous streams. Herein, we investigated its evolution during the HTL of wastewater algae through ICP-MS, XRD, XANES, and EXAFS. Cu-cysteine complexes (51.5%) and Cu₂S (40.4%) were the main components of Cu in algae, whereas the predominant form was CuS (70.9%) in 220 °C-hydrochar. Model compound experiments indicated that Cu-cysteine could be converted into CuS, while Cu₂S was stable during HTL. However, Cu₂S was partially converted into CuS in the hydrochar. Subsequently, the positive Gibbs free energy (36.8 KJ/mol) indicates that the oxidation from Cu⁺ to Cu²⁺ can't occur spontaneously. Furthermore, cyclic voltammograms demonstrated that hydrochar facilitated the oxidation of Cu₂S due to its higher capability of electron acceptance. All these results prove that hydrochar serves as a catalyst for the conversion of Cu₂S to CuS during HTL. This study firstly elucidated that Cu₂S was oxidized into CuS in the presence of hydrochar, and Cu-cysteine was converted into CuS under HTL. This study provides a critical insight into the transformation mechanism of Cu during the HTL of hazardous streams.

Transformation behaviors and environmental risk assessment of heavy metals during resource recovery from Sedum plumbizincicola via hydrothermal liquefaction

Environmentally sound disposal of hyperaccumulator harvests is of critical importance to industrialization of phytoremediation. Herein, transformation behaviors and environmental risk of heavy metals were comprehensively examined during subcritical hydrothermal liquefaction of Sedum plumbizincicola. It is concluded that low temperature liquefaction favored resource recovery of heavy oil and hydrochars in terms of higher energy density, improved carbon sequestration and less energy consumption. Heavy metals were mainly distributed into hydrochars and water soluble phase with less than 10% in heavy oil. All metal elements except As could be accumulated in hydrochars by extending reaction time, whereas more than 96% of As was redistributed into water soluble phase. Prolonged liquefaction time facilitated immobilization of Cd, Cr and As in hydrochars, but fast liquefaction favored Pb stabilization. Liquefaction significantly reduced environmental risk level of Cd, Zn and As, but may mobilize Pb and Mn, especially for Mn to very high risk level at 240 ºC. High temperature with long reaction time tended to inhibit leaching rate of Mn, whereas low liquefaction temperature with short reaction time prevented the leaching of Zn and As from hydrochars. Overall, these findings are essential for downstream upgrading of heavy oil and metals recovery from hydrochars.

Coupling Plant Biomass Derived from Phytoremediation of Potential Toxic-Metal-Polluted Soils to Bioenergy Production and High-Value by-Products—A Review

Phytoremediation is an attractive strategy for cleaning soils polluted with a wide spectrum of organic and inorganic toxic compounds. Among these pollutants, heavy metals have attracted global attention due to their negative effects on human health and terrestrial ecosystems. As a result of this, numerous studies have been carried out to elucidate the mechanisms involved in removal processes. These studies have employed many plant species that might be used for phytoremediation and the obtention of end bioproducts such as biofuels and biogas useful in combustion and heating. Phytotechnologies represent an attractive segment that is increasingly gaining attention worldwide due to their versatility, economic profitability, and environmental co-benefits such as erosion control and soil quality and functionality improvement. In this review, the process of valorizing biomass from phytoremediation is described; in addition, relevant experiments where polluted biomass is used as feedstock or bioenergy is produced via thermo- and biochemical conversion are analyzed. Besides, pretreatments of biomass to increase yields and treatments to control the transfer of metals to the environment are also mentioned. Finally, aspects related to the feasibility, benefits, risks, and gaps of converting toxic-metal-polluted biomass are discussed.

A review on the thermal treatment of heavy metal hyperaccumulator: Fates of heavy metals and generation of products

Phytoremediation is perceived as a promising technique for remediation of heavy metal (HM) contaminated soils, while the harvested HM-enriched hyperaccumulator biomass should be appropriately disposed. Recently, various thermal treatments of hyperaccumulator have drawn increasing attention. After thermal treatment, the hyperaccumulator was converted to bio-oil, bio-gas, biochar, or ash in accordance with the corresponding conditions, and the HMs were separated, immobilized, or trapped. The migration and transformation of HMs during the thermochemical conversion processes are critical for the safe disposal and further utilization of HM hyperaccumulator. This paper provides a systematic review on the migration and transformation of typical HMs (Cd, Ni, Mn, As, and Zn) in hyperaccumulator during various thermochemical conversion processes, and special emphasis is given to the production and application of targeted products (e.g. biochar, hydrochar, bio-oil, and syngas). Besides, future challenges and perspectives in the thermal treatment of hyperaccumulator are presented as well. The distribution and speciation of HMs were influenced by thermal technique type and reaction conditions, thereby affecting the utilization of the derived products. This review suggests that speciation and availability of HMs in hyperaccumulator are tunable by varying treatment techniques and reaction conditions. This information should be useful for the selective conversion of hyperaccumulator into green and valuable products.

The migration, transformation, and risk assessment of heavy metals in residue and bio-oil obtained by the liquefaction of pig manure

The total contents and chemical speciation analysis of Zn, Cu, Pb, Cr, Mn, Ni, Cd, and As in pig manure (PM), liquefaction residues (LRs), and bio-oils (BOs) derived from PM by liquefaction with ethanol as a solvent at 180-300 °C were thoroughly investigated in this study. The environment risk assessment, leachability, and bioavailability of heavy metals in PM and LRs were studied. The results showed that more than 75% of heavy metals remained in LRs. The total contents of heavy metals in LRs were markedly elevated, but those in BOs gradually decreased with the increase in liquefaction temperature. Moreover, the acid soluble/exchangeable fraction and reducible fraction (F1 + F2) of heavy metals in LRs and BOs was significantly reduced, while oxidizable fraction and stable fraction (F3 + F4) desirably increased after liquefaction. Furthermore, the potential risk of heavy metals in LRs was decreased in comparison to that in PM, but the risk of Pb, Mn, and As had not been obviously reduced; therefore, the LRs from the liquefaction of PM should be pretreated before recycling. Temperatures from 220 to 260 °C were the optimum conditions for disposing of PM by liquefaction with ethanol.

Molecular characterization and environmental impacts of water-soluble organic compounds of bio-oil from the thermochemical treatment of domestic sewage sludge

Water-soluble organic compounds derived from bio-oil (WOCB) are regarded as potential risk sources of sludge thermochemical treatment. This study showed that 10.35 mg of water-soluble organic carbon and 1.32 mg of water-soluble organic nitrogen were released per gram of sludge when the final temperature of thermochemical treatment was 600 °C. WOCB was mainly formed at 300-500 °C. Furthermore, FT-ICR MS results indicated that high temperatures promoted deamination reactions, and low molecular weight (LMW) compounds with low oxygen number polymerized into aromatic compounds with increasing temperature. Noteworthily, WOCB released at 20-600 °C showed strong phytotoxicity to wheat. LMW compounds with lignin/carboxylic rich alicyclic molecules (CRAM)-like structures derived from low temperatures (200-400 °C) induced this inhibitory effect, but lipids containing nitrogen and sulfur from high temperatures (400-600 °C) can act as nutrients to promote wheat growth. This study provides theoretical support for the risk control and benefits assessments of sludge thermochemical treatment.

Organoarsenic conversion to As(III) in subcritical hydrothermal reaction of livestock manure

Liquid phase produced by the subcritical hydrothermal liquefaction (HTL) of livestock manure is extensively used in agronomic and environmental applications, but the potential risks caused by inherent pollutants (e.g., roxarsone, ROX) of the livestock manure have not been considered. This study shows that less toxic ROX is completely converted into highly toxic As(III) and As(V) in the HTL reaction with temperature more than 240 °C. Moreover, more than 81.5% of As is distributed in the liquid phase generated by the livestock manure HTL reaction. Notably, the hydrothermal products of livestock manure facilitate the conversion of As(V) to As(III). The resulting hydrochar and aldehydes act as electron donors for As(V) reduction, thus resulting in the formation of As(III). Furthermore, the dissociated As promotes the depolymerization and deoxygenation of the macromolecular compounds to produce more small oxygen-containing compounds such as aldehydes, further boosting the As(V) reduction to As(III). These results indicate that the liquid phase of the livestock manure has potential risks in applications as a fertilizer. Such findings have substantial implications in biomass utilization and redox reactions of envirotechnical and biogeochemical relevance.

Self-cleaning isotype g-C3N4 heterojunction for efficient photocatalytic reduction of hexavalent uranium under visible light

Photocatalysis is a promising method to eliminate hexavalent uranium (U(Ⅵ)) and recycle it from wastewater. However, most of researched photocatalysts are metal-contained, inactive in visible light, and inconvenient to recycle, which unfortunately impedes the further utilization of photocatalytic technology in U(Ⅵ) pollution treatment. Herein, g-C₃N₄ isotype heterojunction with interpenetrated tri-s-triazine structure (ipCN) was prepared by inserting urea into the interlayer of tri-s-triazine planes of thiourea-derived g-C₃N₄ and in-site thermal treating. The synthesized nanocomposites were used to convert soluble U(Ⅵ) ions into U(Ⅳ) sediment under visible light. Experimental and characterization results reveal that ipCN possess larger BET surface area, more negative-charged surface, higher U(Ⅵ) adsorption capability, and more efficient mass diffusion and charges transfer properties. With these excellent characteristics, nearly 98% U(Ⅵ) could be removed within 20 min over ipCN_5:1 and 92% photoreduction efficiency could also be kept after 7 cycle uses, which were equal to or even superior than most reported metal-based photocatalysts. It is also proven that the configuration of U(Ⅵ) and photogenerated ·O₂^- play a significant role in the photocatalytic U(Ⅵ) reduction process, with (UO₂)_x(OH)_y^2x-y are more prone to be adsorbed and the photoinduced process of ·O₂^- will steal electrons from photocatalysts. Furthermore, with the self-generated ·O₂^- and H₂O₂, a green and facile regeneration process of photocatalysts was proposed This work provides a promising scheme to extract U(Ⅵ) from the perspectives of photocatalysts exploitation, photocatalytic reduction, and photocatalysts regeneration, which is meaningful for the sustainable U(Ⅵ) resource recovery and U(Ⅵ) pollution purification.

Environment-enhancing process for algal wastewater treatment, heavy metal control and hydrothermal biofuel production: A critical review

Coupling algae growth on wastewater with hydrothermal liquefaction (HTL) is regarded as an environment-enhancing pathway for wastewater management, biomass amplification, sustainable energy generation and value-added products generation. Through this integrated pathway, microalgae can not only recover nitrogen and phosphorus, but also absorb heavy metals from the wastewater. The migration and transformation of heavy metals need to be specifically assessed and considered due to the environmental concerns associated with metal toxicity. This work reviewed recent advances with respect to bioremediation mechanisms. Particular emphasis was placed on the heavy metal migration, transformation, and the key factors involved in algal wastewater treatment and biomass conversion. Additionally, the challenges of coupling algae wastewater treatment, hydrothermal conversion, and heavy metal control were addressed. Finally, a paradigm involving enhanced algal wastewater treatment and bioenergy production for field application was proposed.

Characterization of biofuel production from hydrothermal treatment of hyperaccumulator waste (Pteris vittata L.) in sub- and supercritical water

In this study, hyperaccumulator waste, i.e., Pteris vittata L. was converted into bio-oil, biogas and biochar via sub- and supercritical hydrothermal liquefaction processes. These products were characterized in terms of EI/MS, FTIR, TGA and GC to understand their chemical composition, thermal decomposition, structural properties and high biofuel reactivity. Characterization results revealed that the dominant chemical components in the heavy bio-oil were esters (40.22%), phenols (20.02%), alcohols (10.16%), organic acids (9.07%), nitrogenous compounds (8.83%) and ketones/aldehydes (6.42%), while the light oil was rich with a higher fraction of phenols (54.13%) and nitrogenous compounds (27.04%). Particularly, bio-oils obtained from supercritical conditions contained increased phenolic compounds and reduced oxygenated chemicals such as alcohols, aliphatic acid, ketones and aldehydes, suggesting the improved quality of bio-oil due to the reduction in oxygen contents. Meanwhile, H2-rich syngas production with the H2 yield of 38.87% was obtained at 535 °C for 20 min, and higher reaction temperature presented a positive influence on H2 production during Pteris vittata L. liquefaction. Moreover, the remaining biochar product was analyzed to determine whether it could be used as a direct solid fuel or auxiliary fuel. This study provided full exploitation of this feedstock waste in energy and valuable chemical complexes.

Advances in lignin valorization towards bio-based chemicals and fuels: Lignin biorefinery

Lignin is one of the most promising renewable sources for aromatic hydrocarbons, while effective depolymerization towards its constituent monomers is a particular challenge because of the structural complexity and stability. Intensive research efforts have been directed towards exploiting effective valorization of lignin for the production of bio-based platform chemicals and fuels. The present contribution aims to provide a critical review of key advances in the identification of exact lignin structure subjected to various fractionation technologies and demonstrate the key roles of lignin structures in depolymerization for unique functionalized products. Various technologies (e.g., thermocatalytic approaches, photocatalytic conversion, and mechanochemical depolymerization) are reviewed and evaluated in terms of feasibility and potential for further upgrading. Overall, advances in pristine lignin structure analysis and conversion technologies can facilitate recovery and subsequent utilization of lignin towards tailored commodity chemicals and fungible fuels.

Inherent Metals of a Phytoremediation Plant Influence Its Recyclability by Hydrothermal Liquefaction

Plants used for phytoremediation of contaminated soil are often enriched in certain metals present in the soil. However, the role of the inherent metal content of the plants on their recycling by hydrothermal liquefaction (HTL) has not been considered in previous studies. The present study showed that Rhus chinensis plants grown in highly Pb-polluted soil can release inherent metals (such as Pb, K, Ca, Na, and Mg) into the HTL solution, further enhancing the production of formic and acetic acids and decreasing the yield of levulinic acid. Theoretical calculations using HTL reactions of model compounds showed that a low Pb content could enhance production of levulinic and formic acids via catalysis of the rehydration reaction for 5-(hydroxymethyl)furfural, while a high Pb content promoted the decomposition of levulinic acid to acetic acid. Fourier transform ion cyclotron resonance mass spectrometry analysis confirmed that Pb²⁺ preferentially promoted the depolymerization of macromolecular compounds with the lignin structure. In general, the inherent metals occurring in the phytoremediation plant influenced the production of organic acids during HTL recycling. Undoubtedly, the combination of phytoextraction and HTL reaction can present a practical pathway toward a sustainable soil remediation technology.

Nonthermal air plasma dehydration of hydrochar improves its carbon sequestration potential and dissolved organic matter molecular characteristics

Labile organic compounds are associated with high environmental risk and are common on hydrochar surfaces. However, a comprehensive re-evaluation of hydrochar properties after the removal of labile compounds has long been overlooked. This study confirms that air-based nonthermal plasma can successfully modify hydrochar properties and change hydrochar's environmental benefits. NMR and FTIR results indicate that, aliphatic and alkyl structures are more reactive, while aromatic structures are highly resistant to the hydrochar modification process, leading to increased carbon sequestration potential and decreased dissolved organic matter (DOM). Van Krevelen diagram results indicate that dehydration controls the hydrochar modification process and leads to a decrease in oxygen content and O/C atomic ratio in the hydrochar; this weakens the ability of the hydrochar to immobilize hydrophobic organic pollutants (such as triclosan) due to the decrease in O‑alkyl C species within the hydrochar. Most importantly, air-based nonthermal plasma changes the structures of hydrochar associated DOM, and high molecular weight (>351 Da), and high degree of unsaturation and oxidation in the modified-hydrochar DOM compounds is observed. This study is therefore considered to have important implications for the carbon cycle and sustainable application of hydrochar.

Production Temperature Effects on the Structure of Hydrochar-Derived Dissolved Organic Matter and Associated Toxicity

Hydrochar is a carbonaceous material derived from hydrothermal liquefaction, and it carries good potential as a new material for environmental applications. However, little is known about the dissolved organic matter (DOM) associated with hydrochar and the consequences of its release. The relationship between the production temperature and the characteristics of DOM released from hydrochar as well as the associated biotoxicity was investigated using a suite of advanced molecular and spectroscopic tools. With the increase in production temperature, the resulted hydrochar-based DOM contained a higher content of phenols and organic acids but less sugars and furans. Meanwhile, the molecular structure of DOM shifted to lower molecular weight with higher organic contents containing <6 O atoms per compound, aromatics, and N-containing substances. While low-temperature hydrochar-derived DOM showed minimal biotoxicity, increase in production temperature to 330 °C led to a great rise in toxicity. This might be attributed to the increased contents of phenols, organic acids, and organics containing <6 O atoms and 1 N atom per compound. These results suggest that hydrochar-derived DOM have more negative impacts on the environment than the organics associated with biochar production. Such understanding highlights the importance of controlling the hydrochar production process.