A Comparison between the Oil Removal Capacity of Polymer-Coated Magnetic Nanoparticles in Natural and Synthetic Environmental Samples

Anisotropic cellulose nanocrystalline sponge sheets with ultrahigh water fluxes and oil/water selectivity

Oily sewage caused by oil spill accidents has become a severe problem in the last decades. Hence, two-dimensional sheet-like filter materials for oil/water separation have received widespread attention. Porous sponge materials were developed using cellulose nanocrystals (CNCs) as raw materials. They are environmentally friendly and easy to prepare, with high flux and separation efficiency. The 1,2,3,4-butane tetracarboxylic acid cross-linked anisotropic cellulose nanocrystalline sponge sheet (B-CNC) exhibited ultrahigh water fluxes driven by gravity alone, depending on the aligned structure of channels and the rigidity of CNCs. Meanwhile, the sponge gained superhydrophilic/underwater superhydrophobic wettability with an underwater oil contact angle of up to 165.7° due to its ordered micro/nanoscale structure. B-CNC sheets displayed high oil/water selectivity without additional material doping or chemical modification. For oil/water mixtures, high separation fluxes of approximately 100,000 L·m^-2·h^-1 and separation efficiencies of up to 99.99 % were obtained. For a Tween 80-stabilized toluene-in-water emulsion, the flux reached >50,000 L·m^-2·h^-1, and the separation efficiency was above 99.7 %. B-CNC sponge sheets showed significantly higher fluxes and separation efficiencies than other bio-based two-dimensional materials. This research provides a facile and straightforward fabrication method of environmental-friendly B-CNC sponges for rapid, selective oil/water separation.

Demulsification Performance and Mechanism of Tertiary Amine Polymer-Grafted Magnetic Nanoparticles in Surfactant-Free Oil-in-Water Emulsion

Numerous cationic magnetic nanoparticles (MNPs) have previously been developed for demulsifying oil-in-water (O/W) emulsion, and results showed that the cationic MNPs could effectively flocculate and remove the negatively charged oil droplets via charge attraction; however, to the best of our knowledge, there are no research reports regarding the synergetic influence of both the positive charge density and interfacial activity of MNPs on the demulsification performance. In this study, three tertiary amine polymer-grafted MNPs, namely, poly(2-dimethylaminoethyl acrylate)-grafted MNPs (M-PDMAEA), poly(2-dimethylamino)ethyl methacrylate)-grafted MNPs (M-PDMAEMA), and poly(2-diethylaminoethyl methacrylate)-grafted MNPs (M-PDEAEMA), were synthesized and evaluated for their demulsification performance. Results demonstrated that a high positive charge density and superior interfacial activity of MNPs could cause partial oil droplet re-dispersion when excessive MNPs were introduced, leading to a lower magnetic separation efficiency and narrower demulsification window. Herein, a demulsification window is defined as a range of nanoparticle dosages in which the MNPs can effectively demulsify the O/W emulsion under certain conditions. For highly positively charged MNPs, their good interfacial activity could aggravate the formation of a narrower demulsification window. When tertiary amine polymer-grafted MNPs carried a lower positive charge density or weak interfacial activity, that is, M-PDMAEA at pH 4.0, M-PDMAEMA at pH 5.0-9.0, and M-PDEAEMA at pH 9.0-10.0, wide demulsification windows were observed. Additionally, a recycling experiment suggested that MNPs could maintain high demulsification efficiency up to at least five cycles, indicating their satisfactory recyclability. The three tertiary amine polymer-grafted MNPs can be potentially used for efficient demulsification from surfactant-free O/W emulsion in various pH ranges.

Porous Polymers Containing Metallocalix[4]arene for the Extraction of Tobacco-Specific Nitrosamines

We designed porous polymers with a tungsten-calix[4]arene imido complex as the nitrosamine receptor for the efficient extraction of tobacco-specific nitrosamines (TSNAs) from water. The interaction between the metallocalix[4]arene and the TSNA, 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (nicotine-derived nitrosamine ketone, NNK) was investigated. We found that the incorporation of the nitrosamine receptor into porous polymers increased their selectivity toward NNK over nicotine. The polymer with an optimal ratio of calixarene-containing and porosity-inducing building blocks showed a high maximum adsorption capacity of up to 203 mg/g toward NNK under sonication, which was among the highest values reported. The adsorbed NNK could be removed from the polymer by soaking it in acetonitrile, enabling the adsorbent to be reused. A similar extraction efficiency to that under sonication could be achieved using the polymer-coated magnetic particles under stirring. We also proved that the material could efficiently extract TSNAs from real tobacco extract. This work not only provides an efficient material for the extraction of TSNAs but also offers a design strategy for efficient adsorbents.

Exploring the characteristics, performance, and mechanisms of a magnetic-mediated washing fluid for the cleanup of oiled beach sand

In the present study, an innovative, environmentally benign recyclable, and magnetically mediated surface washing fluid based on water-dispersible magnetite nanoparticles has been designed and investigated for the cleanup of oiled beach sand. The characterization results showed that the as-prepared magnetite nanoparticles had a spherical morphology with an average diameter of around 250 nm and the particle surface was successfully functionalized with carboxyl groups. The magnetite nanoparticles could be easily re-dispersed by lightly shaking the dispersion after withdrawing the magnet. In addition, prolonging the magnetic field strength and response time promoted the oil recovery from the washing effluent. Thermodynamic modeling was applied to theoretically elucidate the mechanism and the results were in alignment with the experimental findings. Four mechanisms were identified to likely affect surface washing performance. The magnetic fluid had a relatively low operation cost and good reusability for a number of multiple cycles. In terms of other operational limitations, it was noted that washing performance declined as clay (kaolinite) concentrations and salinity values increased. Based on these findings, the proposed stable, low-cost magnetite fluid formulation warrants further investigation as the basis for an operational system for the cleanup of sand beaches contaminated by oil spills.

A Comprehensive Characterization of Different Fractions of Corn Stover and Their Relationships to Multipollutant Sorption Characteristics

Corn stover (CS) is mainly composed of three parts: pith (CSP), rind (CSR), and leaf (CSL). These parts have different lignocellulosic constituents and structural properties. Herein, biosorbents derived from individual corn stover constituents were prepared in an effort to determine the significance of each constituent for multipollutant removal. In this study, SEM, BET, XRD, FTIR, XPS, fibre composition, and contact angle measurements were used to characterize and analyse the physical and chemical properties of the three components of CS and to study their adsorption effects, adsorption isotherms, and kinetics. The lignocellulosic compositions of CSP and CSR were similar, the cellulose content in CSP and CSR was significantly higher than that in CSL, and the hemicellulose content of CSL was much higher than those of CSP and CSR. The minimum lignin content was found in CSP, and the maximum lignin content was found in CSR. The results show that each component had a certain adsorption effect on typical organic pollutants (antibiotics, oils, and dyes). CSP had the strongest oil adsorption capacity, CSR was more suitable for adsorbing antibiotics, and CSL had outstanding adsorption capacity for dye. The pseudo-second-order model and the Langmuir adsorption isotherm model could describe the adsorption processes well, and they consisted of monolayer adsorption accompanied by chemical adsorption reactions. The focus of this study was to provide references for selecting effective adsorbent precursors to remove organic pollutants from wastewater.

Application of Fe3O4 magnetite nanoparticles grafted in silica (SiO2) for oil recovery from oil in water emulsions

In this study, an innovative magnetic demulsifier (MD) was prepared by grafting a silica layer onto the surface of the Fe₃O₄ magnetic nanoparticles (MNPs) using the modified Stober process. The MD was characterized using various analytical techniques (XRD, FTIR, TGA, TEM, VSM, etc.) and employed to recover oil from O/W emulsion, which were then regenerated and recycled several times. The effects of magnetic demulsifier dosage (MD_dose), the concentration of oil (C_oil), pH, the concentration of the surfactant (C_sur), and separation time (t_sep) on the demulsification efficiency (%η_dem), and the percentage of oil recovered (%R_oil) were evaluated. An excellent %η_dem ≥ 90% was achieved C_oil in the range 50-2000 mg/L. Using an MD_dose as low as 10 mg/L attained a %η_dem in the range of 93%-94.3% for O/W mixtures with C_oil < 2000 mg/L, which slightly decreased to ∼90% for higher concentrations. The reported %R_oil (p-value <0.05) was >90 ± 0.1 for tests carried out with pH ≤ 7 and C_sur ≤ 0.1 g/L and declined at higher pH and C_sur to % 86.5 due to the increase in emulsion stability. The developed MD exhibited high recyclability at an effective and stable %R_oil and %η_dem of ∼90% and 86.4% after 9 cycles, respectively. Demulsification process best fits the combined Langmuir-Freundlich (L-F) isotherm with highest adsorption capacity (Q_max) of 186.0 ± 5 mg_oil/g_MD compared to 86.0 ± 5 mg_oil/g_MD for Fe₃O₄, which is 1.1 folds greater than Q_max reported in the literature for other demulsifiers.