Modeling of Mixed Mechanism Adsorption Processes Driven by Surface Adsorption and Internal Ion Exchange

UiO66-based molecularly imprinted polymers with water-compatible deep eutectic solvent as functional monomer for purification of lysozyme from egg white

Protein-templated molecularly imprinted polymers have limitations such as poor mass transfer, slow recognition kinetics, and difficulties in isolation and purification due to their large molecular sizes, complex structures, and flexible conformations. To address these limitations and obtain lysozyme (Lyz)-imprinted polymers, a molecularly imprinted polymer (UiO66@DES-MIPs) was prepared for the first time by using Lyz as a template molecule, a metal-organic framework (UiO66-NH2) as a matrix, and a water-compatible deep eutectic solvent (DES) as a functional monomer. The introduction of UiO66-NH2 by the solvothermal method with a large specific surface area and favorable stability and resistance to environmental disturbances into the MIPs can reduce the "embedding" phenomenon and acquire a higher binding capacity and fast mass transfer. In addition, a water-soluble binary DES (1:2 molar ratio of choline chloride to 1,3 dimethylurea) prepared by a hydrothermal method as a functional monomer generates multiple forces with Lyz, increasing the hydrophilicity of UiO66@DES-MIPs and contributing to the formation and stabilization of the imprinted sites. Consequently, UiO66@DES-MIPs exhibited good selectivity, water compatibility, and fast adsorption equilibrium (the adsorption equilibrated at 243.87 ± 4.88 mg g-1 in 90 min). Besides, reusability experiments indicated that the UiO66@DES-MIPs could be recycled six times without obvious loss of adsorption capacity. The imprinting factor of UiO66@DES-MIPs is 3.67. The isolation and purification of Lyz from egg white confirmed the practicability of UiO66@DES-MIPs. The high adsorption capacity and specific recognition make this polymer a promising candidate for the isolation and purification of biological macromolecules.

Simulation of Adsorption Process of l-Tryptophan on Mixed-Mode Resin HD-1 with Combined Physical Adsorption and Ion Exchange

The mass-transfer process of l-tryptophan (l-Trp) in the hydrophobic interaction/ion-exchange mixed-mode resin HD-1 particles and fixed bed was studied experimentally and theoretically. The adsorption kinetics of l-Trp in single-component and multicomponent adsorption systems was investigated under different pH conditions. The co-adsorption of sodium ions (Na⁺) and l-Trp anions was found to be negligible. A modified liquid-film linear driving force model considering the physical adsorption of l-Trp zwitterions and anions as well as ion exchange of l-Trp cations was proposed. The dissociation equilibria of l-Trp molecules and functional groups on the resin were introduced in the model. The model could well fit the kinetic adsorption curves of l-Trp at different pH values. The presence of Na⁺ and the impurity amino acid l-glutamic acid (l-Glu) did not significantly affect the mass-transfer rate of l-Trp. The dynamic adsorption processes of l-Trp under different pH and concentration conditions were studied. A modified transport-dispersive model considering axial diffusion, liquid-film mass transfer, and a combined physical adsorption and ion-exchange equilibrium was established, which could predict the adsorption breakthrough curves of l-Trp well. During the dynamic adsorption process, the pH of mobile phase in the fixed bed changed with changing the l-Trp concentration in the mobile phase. l-Trp was well separated from Na⁺ and l-Glu with the purity of l-Trp higher than 99%, the recovery rate higher than 95%, and a concentration of 4.69 × 10^-3 mol/L. The elution chromatographic peaks of l-Trp, l-Glu, and Na⁺ and the pH of the outlet solution were predicted satisfactorily.

Adsorption separation of guanosine 5'-Monophosphate and cytidine 5'-Monophosphate by mixed-mode Resin HD-1: Experimental study and mathematical modeling

The preparative separation of guanosine 5'-monophosphate (GMP) and cytidine 5'-monophosphate (CMP) on mixed-mode resin HD-1 was experimentally and theoretically investigated. The adsorption mechanisms of the two nucleotides were elucidated by analyzing adsorption equilibria and kinetics at different pH values. The adsorption dynamics of GMP and CMP in a fixed bed packed with resin HD-1 were studied. All nucleotide monovalent cations, zwitterions, and monovalent anions were adsorbed by the resin. Further, a general adsorption isotherm model was developed by considering the adsorption of different nucleotide species and the dissociation equilibrium behaviors of resin ligands. The model fit the adsorption isotherm data of GMP and CMP well. A modified liquid-film linear driving force model with the combined physical adsorption of nucleotides in different dissociation states and ion exchange of Na⁺ was established. The dissociation equilibria of resin ligands and nucleotides were considered. The model satisfactorily predicted the adsorption kinetic data at different pH values. The values of the efficient diffusion coefficients for GMP and CMP were not significantly influenced by the solution pH. A modified transport-diffusion model with pH gradient elution was proposed. The model accurately predicted the elution chromatographic peaks of GMP and CMP, as well as the pH at the outlet of the fixed bed packed with resin HD-1.

Nanosensing of Acetylcholine Molecules: Influence of the Association Mechanism

A bullet-shaped nanopore surface modified by two polyelectrolyte (PE) layers, an inner polyethyleneimine (PEI) layer and an outer p-sulfonatocalix[4]-arene (SCX4) layer, is applied to sense trace levels of acetylcholine (Ach) molecules. We show that the higher the order of the association reaction of Ach with SCX4, the smaller the difference between the ionic current when Ach is present and that when it is absent, and so is the difference in the space charge density. In addition, the larger the binding constant K of that reaction, the lower the detection limit but narrower the detection range. Choosing pH 7 is most appropriate because if the pH is low, the concentration polarization of H⁺ is significant, and as it gets high, both PE layers become uncharged. At pH 7 and K = 2 × 10⁷ L/mol, the detection limit of the nanopore ranges from 1 to 10 nM, which is orders of magnitude lower than that of the other approaches.