Role of Activated Carbon Precursor in Mercury Removal

Influence of addition of two typical activated carbons on fertility properties and mechanical strength of vegetation concrete under freeze-thaw conditions

Under freeze-thaw conditions, the substrates used for ecological protection degrade, which involves decreases in compactness and fertiliser retention ability. As such, our purpose in this study was to use two typical types of activated carbon (AC), wood-based activated carbon (WAC) and coal-based activated carbon (CAC), to enhance the antifrost property of vegetation concrete (VC). We investigated the effects of five different proportions of planting soil weight (0.5 %, 1 %, 2 %, 4 %, and 6 %) mixed in each type of AC to determine their influence on the physical, mechanical, chemical, and biological properties of VC. The VC samples prepared without AC were used as control check (CK). The results showed that AC addition effectively enhanced the nutrient retention and microorganism capacity of VC under freeze-thaw conditions (10 and 60 freeze-thaw cycles). The leaching loss rate of ammonium nitrogen (NH₄⁺-N) decreased to 31.98 % for WAC-6 %-60 from 46.87 % for CK-60, and the microorganism biomass carbon (MBC) increased to 138.54 mg·kg^-1 for WAC-6 %-60 from 103.52 mg·kg^-1 for CK-60. However, we observed some negative effects, including decreases in the cohesion and internal friction angle. In addition, the water holding capacity and matric suction first increased and then decreased as the proportion of AC mixed in the VC increased, with a turning point of approximately 2 %. By comprehensively considering previous VC eco-restoration technology study results, the recommended mixing amount of AC is 1 %-2 %, which would take full advantage of the benefits of AC and ensure that any negative effect of its use falls within an acceptable range. In addition, WAC generally performed better than CAC, but the aging rate of the former was faster than that of the latter according to scanning electron microscopy (SEM) images and dissolved organic carbon (DOC) analysis. From our results, we concluded that incorporating AC into VC improves the suitability of VC when applied in freeze-thaw conditions.

Removal of mercury(II) from aqueous solution by partially reduced graphene oxide

Mercury (Hg(II)) has been classified as a pollutant and its removal from aqueous sources is considered a priority for public health as well as ecosystem protection policies. Oxidized graphenes have attracted vast interest in water purification and wastewater treatment. In this report, a partially reduced graphene oxide is proposed as a pristine adsorbent material for Hg(II) removal. The proposed material exhibits a high saturation Hg(II) uptake capacity of 110.21 mg g⁻¹, and can effectively reduce the Hg(II) concentration from 150 mg L⁻¹ to concentrations smaller than 40 mg L⁻¹, with an efficiency of about 75% within 20 min. The adsorption of Hg(II) on reduced graphene oxide shows a mixed physisorption–chemisorption process. Density functional theory calculations confirm that Hg atom adsorbs preferentially on clean zones rather than locations containing oxygen functional groups. The present work, therefore, presents new findings for Hg(II) adsorbent materials based on partially reduced graphene oxide, providing a new perspective for removing Hg(II).

Functionalized silica nanoparticles: classification, synthetic approaches and recent advances in adsorption applications

Nanotechnology is rapidly sweeping through all the vital fields of science and technology such as electronics, aerospace, defense, medicine, and catalysis. It involves the design, synthesis, characterization, and applications of materials and devices on the nanometer scale. At the nanoscale, physical and chemical properties differ from the properties of the individual atoms and molecules of bulk matter. In particular, the design and development of silica nanomaterials have captivated the attention of several researchers worldwide. The applications of hybrid silicas are still limited by the lack of control on the morphology and particle size. The ability to control both the size and morphology of the materials and to obtain nano-sized silica particles has broadened the spectrum of applications of mesoporous organosilicas and/or has improved their performances. On the other hand, adsorption is a widely used technique for the separation and removal of pollutants (metal ions, dyes, organics,...) from wastewater. Silica nanoparticles have specific advantages over other materials for adsorption applications due to their unique structural characteristics: a stable structure, a high specific surface area, an adjustable pore structure, the presence of silanol groups on the surface which allow easy modification, less environmental harm, simple synthesis, low cost, etc. Silica nanoparticles are potential adsorbents for pollutants. We present herein an overview of the different types of silica nanoparticles going from the definitions to properties, synthetic approaches and the mention of potential applications. We focus mainly on the recent advances in the adsorption of different target substances (metal ions, dyes and other organics).

Role of Activated Carbon Precursor for Mercury Oxidation and Removal: Oxidized Surface and Carbene Site Interaction

Activated carbon (AC) is widely accepted for the removal of inorganic contaminants like mercury; however, the raw material used in the production of activated carbon is not always taken into consideration when evaluating its efficacy. Mercury oxidation and adsorption mechanisms governed by carbene sites are more likely to occur when graphitic-like activated carbons (such as those produced from high-ranking coals) are employed versus lignocellulosic-based ACs; this is likely due to the differences in carbon structures where lignocellulosic materials are less aromatic. In this research, the team studied bituminous coal-based ACs in comparison to coconut shell and wood-based (both less aromatic) ACs for elemental mercury removal. Nitric acid of 0.5 M, 1 M, and 5 M concentrations along with 10 M hydrogen peroxide were used to oxidize the surface of the ACs. Boehm titrations and FTIR analysis were used to quantify the addition of functional groups on the activated carbons. A trend was observed herein, resulting in increasing nitric acid molarity and an increased quantity of oxygen-containing functional groups. Gas-phase mercury removal mechanisms including physisorption, oxygen functional groups, and carbene sites were evaluated. The results showed significantly better elemental mercury removal in the gas phase with a bituminous coal-based AC embodying similar physical and chemical characteristics to that of its coconut shell-based counterpart. The ACs treated with various oxidizing agents to populate oxygen functional groups on the surface showed increased mercury removal. It is hypothesized that nitric acid treatment creates oxygen functional groups and carbene sites, with carbene sites being more responsible for mercury removal. Heat treatments post-oxidation with nitric acid showed remarkable results in mercury removal. This process created free carbene sites on the surface and shows that carbene sites are more reactive to mercury adsorption than oxygen. Overall, physisorption and oxygen functional groups were also dismissed as mercury removal mechanisms, leaving carbene-free sites as the most compelling mechanism.

Activated Carbon for Pharmaceutical Removal at Point-of-Entry

Pharmaceuticals are an increasing problem in waterways due to improper disposal and lack of removal at wastewater treatment plants. Long-term exposure impacts to humans are unknown but have been observed in model organisms (i.e., fish), impacting reproduction, changing temperament, and causing organ damage. The application of activated carbon (AC) for organic contaminant removal is widespread and applied successfully for water treatment. The objective of this study is to rapidly adsorb ibuprofen using AC to determine the feasibility as a point-of-entry treatment option for removal of pharmaceuticals in the toilet. AC factors analyzed include type of AC raw material, adsorbent particle size, contact time, and competitive adsorption of ibuprofen and common toilet bowl cleaner components such as chlorine and methylene blue dye. A coconut-based AC with a high surface area adsorbed the highest quantity of ibuprofen. There was no significant impact to ibuprofen adsorption upon the introduction of other compounds to the solution, thus demonstrating rapid adsorption and the potential for application at the point-of-entry.

Roles of London Dispersive and Polar Components of Nano-Metal-Coated Activated Carbons for Improving Carbon Dioxide Uptake

Adsorption using carbonaceous materials has been considered as the prevailing technology for CO2 capture because it offers advantages such as high adsorption capacity, durability, and economic benefits. Activated carbon (AC) has been widely used as an adsorbent for CO2 capture. We investigated CO2 adsorption behaviors of magnesium oxide-coated AC (MgO-AC) as a function of MgO content. The microstructure and textural properties of MgO-AC were characterized by X-ray diffraction and nitrogen adsorption–desorption isotherms at 77 K, respectively. The CO2 adsorption behaviors of MgO-AC were evaluated at 298 K and 1 atm. Our experimental results revealed that the presence of MgO plays a key role in increasing the CO2 uptake through the interaction between an acidic adsorbate (e+) and an efficient basic adsorbent (e−).