TiO2 Nanotubes: An Advanced Electron Transport Material for Enhancing the Efficiency and Stability of Perovskite Solar Cells

Porosity-dependent photoelectrochemical activity of double-layered TiO2 thin films deposited by spin-coating method

Photoelectrochemical (PEC) cells made of low-cost, chemically stable, and abundant materials are crucial for green hydrogen production. In this regard, the fabrication of porous films with high light trapping ability and a large contact area is crucial for the production of efficient PEC cells. In this report, anatase TiO2 thin films with a porous double-layered structure were successfully prepared using a conventional spin-coating deposition method. Various amounts of polystyrene spheres were used as a pore-templating agent to control the porosity of the films. A range of characterization techniques, such as scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and photoluminescence were employed to assess the morphology, structural and optical properties of prepared TiO2 films. PEC measurements revealed that prepared double-layered TiO2 thin films exhibit porosity-dependent photocatalytic activity. For example, TiO2 films with an optimized porous structure demonstrated an increase in photocurrent density by a factor of ∼2.23 (to 141.7 μA cm-2) and photoconversion efficiency improvement by a factor of ∼2.14 as compared to non-porous double-layered TiO2 reference films. Absorbance and photoluminescence analysis confirmed that improved PEC activity can be attributed to increased light absorption by the porous structure and reduced charge carrier recombination.

Effect of the Deposition of Vanadium-Oxide on the Photocatalytic Activity of TiO2 Nanotubes and Its Photodiode Performance Interfaced with CH3NH3PbI3 Single Crystal

In this study, we report the influence of vanadium oxide (VO), as a photosensitive component, on the photoactivity of TiO2 nanotubes (TNTs). A series of TNTs of varying tube diameter were synthesized by the anodization of titanium foils at different voltages, while vanadium oxide was deposited on TNTs by wet chemical deposition. An improvement in the optical properties of nanotubes was observed after the deposition of vanadium oxide. An improvement in the optical properties (redshift in UV-Vis spectra) of TNTs and TNT/VO was noted. The photocatalytic activity was improved with increasing tube diameter, while it was weakened after the deposition of VO. Furthermore, photoactivity was investigated in photodiodes based on TNTs or TNT/VO and single crystals of CH3NH3PbI3. The photoelectric measurement revealed that different TNT diameters did not influence the I-V characteristic of the photodiodes, while the deposition of VO improved the photocurrent for smaller TNTs.

A Morphological Study of Solvothermally Grown SnO2 Nanostructures for Application in Perovskite Solar Cells

Tin(IV) oxide (SnO₂) nanostructures, which possess larger surface areas for transporting electron carriers, have been used as an electron transport layer (ETL) in perovskite solar cells (PSCs). However, the reported power conversion efficiencies (PCEs) of this type of PSCs show a large variation. One of the possible reasons for this phenomenon is the low reproducibility of SnO₂ nanostructures if they are prepared by different research groups using various growth methods. This work focuses on the morphological study of SnO₂ nanostructures grown by a solvothermal method. The growth parameters including growth pressure, substrate orientation, DI water-to-ethanol ratios, types of seed layer, amount of acetic acid, and growth time have been systematically varied. The SnO₂ nanomorphology exhibits a different degree of sensitivity and trends towards each growth factor. A surface treatment is also required for solvothermally grown SnO₂ nanomaterials for improving photovoltaic performance of PSCs. The obtained results in this work provide the research community with an insight into the general trend of morphological changes in SnO₂ nanostructures influenced by different solvothermal growth parameters. This information can guide the researchers to prepare more reproducible solvothermally grown SnO₂ nanomaterials for future application in devices.

Mostafa R, H. Zeenelabden H, M. Mabrouk M, Mourtada Elseman A, Gad N, El-Aasser M, M. Rashad M. Mixed 2D-3D Halide Perovskite Solar Cells

The 3D-perovskite halides have gained a considerable reputation versus their counterpart semiconductor materials since they achieved a remarkable high-power conversion efficiency of 25.2% within a decade. Perovskite solar cells also have some problems as lattice degradation and sensitivity against moisture, oxygen, and strong irradiation. The perovskite instability is the drawback in front of this emerging technology towards mass production and commercialization. 2D-perovskites, with the general formula A2Bn − 1MnX3n + 1, have been recently introduced to overcome some of the drawbacks of the stability of 3D-perovskites; however, this is at the expense of sacrificing a part of the power conversion efficiency. Mixed 2D/3D perovskites could solve this dilemma towards the way to high stability-efficiency perovskites. The research is expected to obtain highly stable and efficient mixed 2D/3D perovskite solar cells in the few coming years. This chapter reviews 2D-perovskites’ achieved progress, highlighting their properties, current trends, challenges, and future prospects.

Semiconductors as Effective Electrodes for Dye Sensitized Solar Cell Applications

As proficient photovoltaic devices, dye-sensitized solar cells (DSSCs) have received considerable consideration in recent years. In order to accomplish advanced solar-to-electricity efficiency and increase long-term functioning stability, improvements in the configuration structure of DSSCs are essential, as is an understanding of their elementary principles. This work discusses the application of different semiconductor constituents designed for effective DSSCs. The main parameters crucial to fabrication of DSSC electrodes in nano-porous semiconductor structures are high surface area and large pore size. Different inorganic semiconductor materials are used to load sensitizer dyes, which absorb a lot of light and induce high photocurrent for efficient DSSCs. The first section of the review covers energy sources, photovoltaics, and the benefits of solar cells in daily life, while the second part includes the various types of semiconductors applied in DSSC applications. The final section provides a brief review of future perspectives for DSSCs and a survey of semiconductor materials proposed for solar cell applications.

Graphene assisted crystallization and charge extraction for efficient and stable perovskite solar cells free of a hole-transport layer

In recent times, perovskite solar cells (PSCs) have been of wide interest in solar energy research, which has ushered in a new era for photovoltaic power sources through the incredible enhancement in their power conversion efficiency (PCE). However, several serious challenges still face their high efficiency: upscaling and commercialization of the fabricated devices, including long-term stability as well as the humid environment conditions of the functional cells. To overcome these obstacles, stable graphene (G) materials with tunable electronic features have been used to assist the crystallization as well as the charge extraction inside the device configuration. Nonetheless, the hole transport layer (HTL)-free PSCs based on graphene materials exhibit unpredictable results, including a high efficiency and long-term stability even in the conditions of an ambient air atmosphere. Herein, we combine graphene materials into a mesoporous TiO2 electron transfer layer (ETL) to improve the coverage and crystallinity of the perovskite material and minimize charge recombination to augment both the stability and efficiency of the fabricated mixed cation PSCs in ambient air, even in the absence of a HTL. Our results demonstrate that an optimized PSC in the presence of different percentages of graphene materials displays a PCE of up to 17% in the case of a G:TiO2 ETL doped with 1.5% graphene. With this coverage and crystallinity amendment approach, we show hysteresis-free and stable PSCs, with less decomposition after ∼3000 h of storage under a moist ambient atmosphere. This work focuses on the originalities of the materials, expenses, and the assembling of stable and effective perovskite solar cells.