Improvement of Ni/Al2O3 Catalysts for Low-Temperature CO2 Methanation by Vanadium and Calcium Oxide Addition

Graphene-Based Material Supports for Ni- and Ru- Catalysts in CO2 Hydrogenation: Ruling out Performances and Impurity Role

Laboratory-prepared Gnp using molten salt, commercial Gnp and reduced graphene oxide (rGO) have been characterized and utilized as support for CO2 hydrogenation catalysts. Ni- and Ru- catalysts supported over Gnp, commercial Gnp and rGO have been deeply characterized at different stages using Raman, IR, XRD, FE-SEM-EDXS, SEM-EDXS, XPS, and TEM, also addressing carbon loss before reaction and evolved species, thus allowing a better comprehension of the produced materials. Ni and Ru/rGO were inactive while Gnp-supported ones were active. Ru has been found almost completely selective toward reverse Water Gas Shift to CO, approaching the forecasted thermodynamic equilibrium at 723 K, in the tested conditions (YCO~55 %), with an apparent activation energy in the range of 70-90 kJ/mol. Exhaust catalysts pointed out the presence of sulfur partially linked to the carbon matrix and partially producing the corresponding metal sulfide with the detection of surface oxidized species in the cationic form and adsorbed species as well. The metal-based nanoparticles displayed a quite narrow size distribution, confirming the promising behavior of these catalytic systems for CO2 utilization.

Optimization of 3D Printing Parameters for Alumina Ceramic Based on the Orthogonal Test

In this paper, an alumina ink with good rheological properties was successfully prepared using pseudoboehmite as the main component, nitric acid as the colloidal solvent, and sesbania powder as the lubricant. The impact of nine different ink formulations, namely, Ink1 to Ink9, on the printability and rheological features of the ink was investigated. Consequently, it was found that Ink3 with 5 wt % nitric acid and 5 wt % sesbania powder exhibited the most favorable formability. This ink was utilized to fabricate alumina samples with direct ink writing (DIW) three-dimensional (3D) printing technology. The printed alumina samples were characterized using an automatic Brunauer-Emmett-Teller, X-ray diffractometer, Fourier transform infrared spectroscopy, and scanning electron microscope. To obtain the optimal printing parameters, a three-factor and three-level orthogonal test was designed to research the influences of different 3D printing parameters (filling ratio, nozzle diameter, and layer thickness) on the specific surface area, pore characteristics (size and volume), and radial crushing strength of the alumina specimens. The primary and secondary orders of the effects on the radial crushing strength and pore structure were determined through analysis of the experimental data. The experimental results showed that the alumina sample with a filling ratio of 80%, nozzle diameter of 0.6 mm, and layer thickness of 0.3 mm was found to have better strength of 48.07 ± 9.53 N/mm and specific surface area of 185.7315 m2/g. This study provides a theoretical base for the preparation of alumina carriers by DIW 3D printing.

Carbon Dioxide Conversion on Supported Metal Nanoparticles: A Brief Review

The increasing concentration of anthropogenic CO2 in the air is one of the main causes of global warming. The Paris Agreement at COP 21 aims to reach the global peak of greenhouse gas emissions in the second half of this century, with CO2 conversion towards valuable added compounds being one of the main strategies, especially in the field of heterogeneous catalysis. In the current search for new catalysts, the deposition of metallic nanoparticles (NPs) supported on metal oxides and metal carbide surfaces paves the way to new catalytic solutions. This review provides a comprehensive description and analysis of the relevant literature on the utilization of metal-supported NPs as catalysts for CO2 conversion to useful chemicals and propose that the next catalysts generation can be led by single-metal-atom deposition, since in general, small metal particles enhance the catalytic activity. Among the range of potential indicators of catalytic activity and selectivity, the relevance of NPs’ size, the strong metal–support interactions, and the formation of vacancies on the support are exhaustively discussed from experimental and computational perspective.

Synthesis of Vanadium-Containing Catalytically Active Phases for Exhaust Gas Neutralizers of Motor Vehicles and Industrial Enterprises

The catalytically active vanadium-containing system of γ-Al2O3 was studied using a wide range of physical and chemical methods, depending on the synthesis conditions. It is shown that the vanadium-containing system includes several complexes with different thermal stabilities and catalytic activities. Low-active complexes are destroyed with the formation of more active ones based on V2O5 oxide, as the temperature of heat treatment increases. It can be assumed that V2O5 oxide has the decisive role in its catalytic activity. It was concluded that the vanadium-containing catalytic system on aluminium oxide, in the studied temperature range, is thermally stable and shows high activity not only in the reduction of nitrogen oxides but also in the oxidation of hydrocarbons (even of the most difficult ones, such as oxidizable methane). These properties of the system make it quite promising in the field of application for the purification of the exhaust gases of motor transport and industrial enterprises with environmentally harmful components, as well as for understanding the mechanism of the action of the catalysts in these processes, which is very important for solving the problems of decarbonization and achieving carbon neutrality.

Developing Benign Ni/g-C3N4 Catalysts for CO2 Hydrogenation: Activity and Toxicity Study

This research discusses the CO2 valorization via hydrogenation over the non-noble metal clusters of Ni and Cu supported on graphitic carbon nitride (g-C3N4). The Ni and Cu catalysts were characterized by conventional techniques including XRD, AFM, ATR, Raman imaging, and TPR and were tested via the hydrogenation of CO2 at 1 bar. The transition-metal-based catalyst designed with atom-economy principles presents stable activity and good conversions for the studied processes. At 1 bar, the rise in operating temperature during CO2 hydrogenation increases the CO2 conversion and the selectivity for CO and decreases the selectivity for methanol on Cu/CN catalysts. For the Ni/CN catalyst, the selectivity to light hydrocarbons, such as CH4, also increased with rising temperature. At 623 K, the conversion attained ca. 20%, with CH4 being the primary product of the reaction (CH4 yield >80%). Above 700 K, the Ni/CN activity increases, reaching almost equilibrium values, although the Ni loading in Ni/CN is lower by more than 90% compared to the reference NiREF catalyst. The presented data offer a better understanding of the effect of the transition metals' small metal cluster and their coordination and stabilization within g-C3N4, contributing to the rational hybrid catalyst design with a less-toxic impact on the environment and health. Bare g-C3N4 is shown as a good support candidate for atom-economy-designed catalysts for hydrogenation application. In addition, cytotoxicity to the keratinocyte human HaCaT cell line revealed that low concentrations of catalysts particles (to 6.25 μg mL-1) did not cause degenerative changes.

Co-Precipitated Ni-Mg-Al Hydrotalcite-Derived Catalyst Promoted with Vanadium for CO2 Methanation

Co-precipitated Ni-Mg-Al hydrotalcite-derived catalyst promoted with vanadium were synthesized with different V loadings (0–4 wt%) and studied in CO₂ methanation. The promotion with V significantly changes textural properties (specific surface area and mesoporosity) and improves the dispersion of nickel. Moreover, the vanadium promotion strongly influences the surface basicity by increasing the total number of basic sites. An optimal loading of 2 wt% leads to the highest activity in CO₂ methanation, which is directly correlated with specific surface area, as well as the basic properties of the studied catalysts.

Wheat-Straw-Derived Activated Biochar as a Renewable Support of Ni-CeO2 Catalysts for CO2 Methanation

Ceria- and urea-doped activated biochars were used as support for Ni-based catalysts for CO2 methanation purposes. Different materials were prepared and tested to find the best catalytic formulation. After several CO2 methanation experiments—carried out at 0.35–1.0 MPa and 300–500 °C—it was found that the most suitable catalyst was a wheat-straw-derived activated biochar loaded with 30 wt.% of CeO2 and 20 wt.% of Ni. Using this catalyst, a CO2 conversion of 65% with a CH4 selectivity of 95% was reached at 1.0 MPa, 400 °C, and 13,200 h−1. From the study of the influence of the gas hourly space velocity, it was deduced that the most likely reaction mechanism was a reverse water–gas shift reaction, followed by CO hydrogenation. N-doping of the carbon support as an alternative to the use of ceria was also investigated. However, both CO2 conversion and selectivity toward CH4 values were clearly lower than those obtained for the ceria-containing catalyst cited above. The outcomes of this work indicate that a renewable biomass-derived support can be effectively employed in the catalytic conversion of CO2 to methane.