Advances in Chelating Resins for Adsorption of Heavy Metal Ions

Removal of Cu (II) by ion exchange resin and its re-utilization of the residual solution from the distilled Lycium barbarum wine

In order to re-utilize the residual from the distillation of the Chinese wolfberry wine and reduce the environmental pollution, the residual is firstly filtered by the ceramic membrane of 50 nm, then the Cu (II) has transferred from the distillation is removed using the ion exchange resin, and the treated solution is recombined with the distilled liquor to make the Chinese wolfberry brandy and the comparison has conducted on the physicochemical properties, antioxidant activity and flavor compounds between the recombined brandy and the finished brandy. The results indicate that the Cu (II) was effectively removed by ceramic membrane combined with the D401 resin. Compared with finished brandy, the recombined brandy contains high contents of polysaccharides, phenols and flavonoids, thus contributing to the improvement of antioxidant capacity. The gas chromatography-ion mobility spectrometry (GC-IMS) reveals that 25 volatile compounds like esters and alcohols have identified in the brandy samples, and the differences are significant between the recombined and the finished brandy. In summary, the distilled residual from the Chinese wolfberry wine might be re-used after the appropriate treatment so as to reduce the discharge and environmental pollution.

A novel bio-based fluorescent N, P-CDs@CMC/PEI composite hydrogel for sensitive detection and efficient capture of toxic heavy metal ions

To address the serious environmental pollution problems of toxic heavy metal ions in water bodies, a novel fluorescent composite hydrogel N, P-CDs@CMC/PEI with a bio-based polymer matrix of carboxylmethyl cellulose (CMC), polyethylenimine (PEI) as a second interpenetrating network and N, P-doped carbon dots (N, P-CDs) as a fluorescent probe was prepared for simultaneous detection and capture of HMIs by a facile and simple one-step approach. The morphology, chemical structure, swelling ratio, mechanical strength and fluorescence property of these composite hydrogels were studied through varied characterization methods. The composite hydrogel showed sensitive and selective fluorescence response with Hg(II) and Fe(III) and the according LOD values were 0.48 and 0.27 mg L-1, respectively. The relationship between the types of the adsorbent, pH value, HMIs concentration and temperature on the adsorption capacity of these composite hydrogels were studied. The pseudo-second-order model and Langmuir model were applicable to explain the adsorption process of CPH2 for Hg(II) and Cr(VI). The maximum calculated adsorption capacities for the above targeted HMIs by Langmuir model were 846.7 and 289.5 mg g-1, respectively. Coexisting inorganic salts and organic acids in low concentration had little effects on Hg(II) and Cr(VI) removal and the composite hydrogel showed good recyclability and stability for Hg(II) and Cr(VI) removal after four cycles. The electrostatic attraction and coordination covalent bonds were responsible for the adsorption process.

Recovery of Ag(I) from Wastewater by Adsorption: Status and Challenges

Untreated or inadequately treated silver-containing wastewater may pose adverse effects on hu-man health and the ecological environment. Currently, significant progress has been made in the treatment of Ag(I) in wastewater using adsorption methods, with adsorbents playing a pivotal role in this process. This paper provides a systematic review of various adsorbents for the recovery and treatment of Ag(I) in wastewater, including MOFs, COFs, transition metal sulfides, metal oxides, biomass materials, and other polymeric materials. The adsorption mechanisms of these materials for Ag(I) are elaborated upon, along with the challenges currently faced. Furthermore, insights into optimizing adsorbents and developing novel adsorbents are proposed in this study.

Recent advances in alginate-based composite gel spheres for removal of heavy metals

The discharge of heavy metal ions from industrial wastewater into natural water bodies is a consequence of global industrialisation. Due to their high toxicity and resistance to degradation, these heavy metal ions pose a substantial threat to human health as they accumulate and amplify. Alginate-based composite gels exhibit good adsorption and mechanical properties, excellent biodegradability, and non-toxicity, making them environmentally friendly heavy metal ion adsorbents for water with promising development prospects. This paper introduces the basic properties, cross-linking methods, synthetic approaches, modification methods, and manufacturing techniques of alginate-based composite gels. The adsorption properties and mechanical strength of these gels can be enhanced through surface modification, multi-component mixing, and embedding. The main production processes involved are sol-gel and cross-linking methods. Additionally, this paper reviews various applications of alginate composite gels for common heavy metals, rare earth elements, and radionuclides and elucidates the adsorption mechanism of alginate composite gels. This study aimed to provide a reference for synthesising new, efficient, and environmentally friendly alginate-based adsorbents and to contribute new ideas and directions for addressing the issue of heavy metal pollution.

Exploring the fluorescence properties of tellurium-containing molecules and their advanced applications

This review article explores the fascinating realm of fluorescence using organochalcogen molecules, with a particular emphasis on tellurium (Te). The discussion encompasses the underlying mechanisms, structural motifs influencing fluorescence, and the applications of these intriguing phenomena. This review not only elucidates the current state of knowledge but also identifies avenues for future research, thereby serving as a valuable resource for researchers and enthusiasts in the field of fluorescence chemistry with a focus on Te-based molecules. By highlighting challenges and prospects, this review sparks a conversation on the transformative potential of Te-containing compounds across different fields, ranging from environmental solutions to healthcare and materials science applications. This review aims to provide a comprehensive understanding of the distinct fluorescence behaviors exhibited by Te-containing compounds, contributing valuable insights to the evolving landscape of chalcogen-based fluorescence research.

A New Approach of Complexing Polymers Used for the Removal of Cu2+ Ions

This study presents two modified polymers for Cu2+ ion removal from aqueous media. Shredded maize stalk (MC) and a strong-base anionic resin (SAX) were modified with indigo carmine (IC) in order to obtain two different complexing polymers, i.e., IC-MC and SAX-IC. Initially, the complex reaction between IC and Cu2+ in the solution was studied. Additionally, the complex formation Cu2+-IC in liquid solutions was evaluated at different pH ranges of 1.5, 4.0, 6.0, 8.0, and 10.0, respectively. For Cu2+ ions, adsorption onto the IC-MC and IC-SAX batch experiments were conducted. The contact time for evaluating the optimum adsorption for Cu2+ ions on the complexing materials was established at 1 h. Efficient Cu2+ ion adsorption on the IC-MC and SAX-IC at pH = 10 was achieved. The adsorption of Cu2+ ions depends on the quantity of IC retained on MC and SAX. At 2.63 mg IC/g MC(S4) and 22 mg IC/g SAX(SR2), a high amount of Cu2+ ion adsorption was reported. The highest adsorption capacity (Qe) of IC-MC was obtained at 0.73 mg/g, and for IC-SAX, it was attained at 10.8 mg/g. Reusability experiments were performed using the HCl (0.5 M) solution. High regeneration and reusability studies of IC-MC and IC-SAX were confirmed, suggesting that they can be used many times to remove Cu2+ ions from aqueous matrices. Therefore, the development of complexing materials could be suitable for Cu2+ ion removal from wastewater.

Efficient multi-ion adsorption using chitosan-malonic acid film: Enhancement using response surface methodology

The objective of this research is to conduct a comprehensive characterization of chitosan while also improving its attributes by crosslinking with malonic acid, with a focus on its efficacy in removing hexavalent chromium, arsenite and fluoride ions. Crosslinking chitosan in 1:0.5 mass ratio forming a film led to substantial enhancement in confiscation of these target pollutants. The characterization of the adsorbent involved several techniques, including FT-IR, TGA-DSC, SEM-EDX, XRD, and BET surface area analysis. In batch adsorption experiments, Chitosan-malonic acid (CMA) was employed to remove CrVI, AsIII and F- from aqueous solutions. These experiments were conducted while varying conditions such as pH, dosage, concentration, temperature, and time. Through the implementation of response surface methodology (RSM), parameters were optimized, resulting in over 95% removal of CrVI, AsIII and F- ions. The isotherm and kinetics data demonstrated a good fit with the Langmuir isotherm model and pseudo second-order kinetics, respectively. According to the Langmuir isotherm, the maximum adsorption capacities on CMA for CrVI, AsIII and F- were determined to be 687.05 mg g-1, 26.72 mg g-1 and 51.38 mg g-1 respectively under optimum pH of 4.0, 7.0 and 5.0 respectively under ambient temperature of 303 K. Thermodynamic analysis indicated that the adsorption process was spontaneous and driven by enthalpy. The regenerability of the adsorbent was validated through five adsorption-desorption cycles, signifying its reusability. An assessment of the adsorbent's sustainability indicated an eco-friendly synthesis, as reflected by the low E-factor value of 0.0028.

Assessing indicators of arsenic toxicity using variable fluorescence in a commercially valuable microalgae: Physiological and toxicological aspects

Indicators signaling Arsenic (As) stress through physiology of microalgae using non-destructive methods like variable fluorescence are rare but requisite. This study reports stress markers indicating arsenic (As) toxicity (in two concentrations 11.25 µg/L and 22.5 µg/L compared to a control) exposed to a microalga (Diacronema lutheri), using fast repetition rate fluorometry (FRRf). Growth and physiological parameters such as cell density, chl a and the maximum quantum yield F_v/F_m showed coherence and impeded after the exponential phase (day 9 - day 12) in As treatments compared to the control (p < 0.05). On contrary photo-physiological constants were elevated showing higher optical (a_LHII) and functional [Sigma (σ_PSII)] absorption cross-section for the As treatments (p < 0.05) further implying the lack of biomass production yet an increase in light absorption. In addition, As exposure increased the energy dissipation by heat (NPQ-NSV) showing a strong relationship with the de-epoxidation ratio (DR) involving photoprotective pigments. Total As bioaccumulation by D. lutheri showed a strong affinity with Fe adsorption throughout the algal growth curve. This study suggests some prompt photo-physiological proxies signaling As contamination and endorsing its usefulness in risk assessments, given the high toxicity and ubiquitous presence of As in the ecosystem.

Preparation of Eco-Friendly Chelating Resins and Their Applications for Water Treatment

In the present study, two chelating resins were prepared and used for simultaneous adsorption of toxic metal ions, i.e., Cr³⁺, Mn²⁺, Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, and Pb²⁺ (M^X+). In the first step, chelating resins were prepared starting with styrene-divinylbenzene resin, a strong basic anion exchanger Amberlite IRA 402(Cl^-) with two chelating agents, i.e., tartrazine (TAR) and amido black 10B (AB 10B). Key parameters such as contact time, pH, initial concentration, and stability were evaluated for the obtained chelating resins (IRA 402/TAR and IRA 402/AB 10B). The obtained chelating resins show excellent stability in 2M HCl, 2M NaOH, and also in ethanol (EtOH) medium. The stability of the chelating resins decreased when the combined mixture (2M HCl:EtOH = 2:1) was added. The above-mentioned aspect was more evident for IRA 402/TAR compared to IRA 402/AB 10B. Taking into account the higher stability of the IRA 402/TAR and IRA 402/AB 10B resins, in a second step, adsorption studies were carried out on complex acid effluents polluted with M^X+. The adsorption of M^X+ from an acidic aqueous medium on the chelating resins was evaluated using the ICP-MS method. The following affinity series under competitive analysis for IRA 402/TAR was obtained: Fe³⁺(44 µg/g) > Ni²⁺(39.8 µg/g) > Cd²⁺(34 µg/g) > Cr³⁺(33.2 µg/g) > Pb²⁺(32.7 µg/g) > Cu²⁺ (32.5 µg/g) > Mn²⁺(31 µg/g) > Co²⁺(29 µg/g) > Zn²⁺ (27.5 µg/g). While for IRA 402/AB 10B, the following behavior was observed: Fe³⁺(58 µg/g) > Ni²⁺(43.5 µg/g) > Cd²⁺(43 µg/g) > Cu²⁺(38 µg/g) > Cr³⁺(35 µg/g) > Pb²⁺(34.5 µg/g) > Co²⁺(32.8 µg/g) > Mn²⁺(33 µg/g) > Zn²⁺(32 µg/g), consistent with the decreasing affinity of M^X+ for chelate resin. The chelating resins were characterized using TG, FTIR, and SEM analysis. The obtained results showed that the chelating resins prepared have promising potential for wastewater treatment in the context of the circular economy approach.

Investigation on the Removal Performances of Heavy Metal Copper (II) Ions from Aqueous Solutions Using Hydrate-Based Method

Since heavy metal ion-contaminated water pollutionis becoming a serious threat to human and aquatic lives, new methods for highly efficient removal of heavy metal ions from wastewater are important to tackle environmental problems and sustainable development. In this work, we investigate the removal performances of heavy metal copper (II) ions from aqueous solutions using a gas hydrate-based method. Efficient removal of heavy metal copper (II) ions from wastewater via a methane hydrate process was demonstrated. The influence of the temperature, hydration time, copper (II) ions concentration, and stirring rate on the removal of heavy metal copper (II) ions were evaluated. The results suggested that a maximum of 75.8% copper (II) ions were removed from aqueous solution and obtained melted water with 70.6% yield with a temperature of -2 °C, stirring speed 800 r/min, and hydration time of 4 h with aninitial copper concentration of 100 mg/L. The initial concentration of copper (II) ions in the aqueous solution could be increased to between 100 and 500 mg/L. Meanwhile, our study also indicated that 65.6% copper (II) ions were removed from aqueous solution and the yield of melted water with 56.7%, even with the initial copper concentration of 500 mg/L. This research work demonstrates great potential for general applicability to heavy metal ion-contaminated wastewater treatment and provides a reference for the application of the gas hydrate method in separation.

New Chelate Resins Prepared with Direct Red 23 for Cd2+, Ni2+, Cu2+ and Pb2+ Removal

In this paper, two chelate resins prepared by a simple procedure were used for the removal of Cd2+, Ni2+, Cu2+, and Pb2+ (M2+) from aqueous solutions. Amberlite IRA 402 strongly basic anion exchange resin in Cl− form (IRA 402 (Cl−) together with Amberlite XAD7HP acrylic ester co-polymer (XAD7HP) were functionalized with chelating agent Direct red 23 (DR 23). The chelate resins (IRA 402-DR 23 and XAD7HP-DR 23) were obtained in batch mode. The influence of interaction time, pH and the initial concentration of DR 23 solution was investigated using UV-Vis spectrometry. The time necessary to reach equilibrium was 90 min for both resins. A negligible effect of adsorption capacity (Qe) was obtained when the DR 23 solution was adjusted at a pH of 2 and 7.9. The Qe of the XAD7HP resin (27 mg DR 23/g) is greater than for IRA 402 (Cl−) (21 mg DR 23/g). The efficiency of chelating resins was checked via M2+ removal determined by the atomic adsorption spectrometry method (AAS). The M2+ removal by the IRA 402-DR 23 and XAD7HP-DR 23 showed that the latter is more efficient for this propose. As a consequence, for divalent ions, the chelated resins followed the selectivity sequence: Cd2+ > Cu2+ > Ni2+ > Pb2+. Additionally, Cd2+, Cu2+ and Ni2+ removal was fitted very well with the Freundlich model in terms of height correlation coefficient (R2), while Pb2+ was best fitted with Langmuir model for IRA 402-DR 23, the Cu2+ removal is described by the Langmuir model, and Cd2+, Ni2+ and Pb2+ removal was found to be in concordance with the Freundlich model for XAD7HP-DR 23. The M2+ elution from the chelate resins was carried out using 2 M HCl. The greater M2+ recovery from chelating resins mass confirmed their sustainability. The chelate resins used before and after M2+ removal by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) analysis were evaluated.