Stability of an Al-Fumarate MOF and Its Potential for CO2 Capture from Wet Stream

Effects of Particle Size on the Gas Uptake Kinetics and Physical Properties of Type III Porous Liquids

Type III porous liquids (PLs) consist of porous solid particles dispersed in a size-excluded liquid phase and are attracting much attention as novel media for applications such as gas separation. However, the effects of fundamental variables such as particle size on their physical properties are currently largely unknown. Here we study the effects of particle size in a series of porous liquids based on solid Al(OH)(fumarate) (a microporous metal-organic framework, MOF) with particle sizes of 60 nm, 200-600 nm, or 800-1000 dispersed in liquid polydimethylsiloxane (PDMS). Properties examined include physical stability of the dispersion, viscosity, total CO2 uptake, and kinetics of CO2 uptake. As expected, both physical stability and viscosity decreased with increasing particle size. Unexpectedly, total gravimetric gas uptake also varied with particle size, being greatest for the largest particles, which we ascribe to larger particles having a lower relative content of surface-bound FMA ligands. Various models for the gas uptake kinetic data were considered, specifically adsorption reaction models such as pseudo-first-order, pseudo-second-order, and Elovich models. In contrast to pure PDMS, which showed first-order kinetics, all PLs fit best to the Elovich model confirming that their uptake mechanism is more complex than for a simple liquid. Adsorption diffusion models, specifically Weber and Morris' intraparticle model and Boyd's model, were also applied which revealed a three-step process in which a combination of diffusion through a surface layer and intraparticle diffusion were rate-limiting. The rate of gas uptake follows the order PDMS < PL1 < PL2 < PL3, showing that the porous liquids take up gas more rapidly than does PDMS and that this rate increases with particle size. Overall, the study suggests that for high gas uptake and fast uptake kinetics, large particles may be preferred. Also, the fact that large particles resulted in low viscosity may be advantageous in reducing the pumping energy needed in flow separation systems. Therefore, the work suggests that finding ways to stabilize PLs with large particles against phase separation could be advantageous for optimizing the properties of PLs toward applications.

Facile mechanochemical synthesis of MIL-53 and its isoreticular analogues with a glance at reaction reversibility

MIL-53 represents one of the most notable metal-organic frameworks given its unique structural flexibility and remarkable thermal stability. In this study, a shaker-type ball milling method has been developed into a facile and generalizable synthetic strategy to access a family of MIL-53 type materials under ambient conditions. During the explorations of [M(OH)(fumarate)] (M = Al, Ga, and In), we report a positive correlation between the metal-ligand (M-L) bond reversibility and the size of resultant crystallites under the mechanochemical process. The more kinetically labile the M-L bond is, the larger the afforded crystallite size is.

The Challenge of Water Competition in Physical Adsorption of CO2 by Porous Solids for Carbon Capture Applications - A Short Perspective

With ever-increasing efforts to design sorbent materials to capture carbon dioxide from flue gas and air, this perspective article is provided based on nearly a decade of collaboration across science, engineering, and industry partners. A key point learned is that a holistic view of the carbon capture problem is critical. While researchers can be inclined to value their own fields and associated metrics, often, key parameters are those that enable synergy between materials and processes. While the role of water in the chemisorption of CO2 is well-studied, in this perspective, it is hoped to highlight the often-overlooked but critical role of water in assessing the potential of a physical adsorbent for CO2 capture. This is a challenge that requires interdisciplinarity. As such, this document is written for a general audience rather than experts in any specific discipline.

Effect of Water and Carbon Dioxide on the Performance of Basolite Metal-Organic Frameworks for Methane Adsorption

MOFs are potential adsorbents for methane separation from nitrogen, including recovery in diluted streams. However, water and carbon dioxide can seriously affect the adsorption performance. Three commercial MOFs, basolite C300, F300, and A100, were studied under similar conditions to fugitive methane streams, such as water (75 and 100% relative humidity) and carbon dioxide (0.33%) presence in a fixed bed. The presence of available open metal sites of copper (Cu2+) and aluminum (Al3+) in the case of basolite C300 and A100, respectively, constitutes a clear drawback under humid conditions, since water adsorbs on them, leading to significant methane capacity losses. Surprisingly, basolite F300 is the most resistant material due to its amorphous structure, which hinders water access. The combination of carbon dioxide and water creates a synergy that seriously affects basolite A100, closely related to its breathing effect, but does not constitute an important issue for basolite C300 and F300.

Low-concentration CO2 capture using metal-organic frameworks - current status and future perspectives

The ever-increasing atmospheric CO₂ level is considered to be the major cause of climate change. Although the move away from fossil fuel-based energy generation to sustainable energy sources would significantly reduce the release of CO₂ into the atmosphere, it will most probably take time to be fully implemented on a global scale. On the other hand, capturing CO₂ from emission sources or directly from the atmosphere are robust approaches that can reduce the atmospheric CO₂ concentration in a relatively short time. Here, we provide a perspective on the recent development of metal-organic framework (MOF)-based solid sorbents that have been investigated for application in CO₂ capture from low-concentration (<10 000 ppm) CO₂ sources. We summarized the different sorbent engineering approaches adopted by researchers, both from the sorbent development and processing viewpoints. We also discuss the immediate challenges of using MOF-based CO₂ sorbents for low-concentration CO₂ capture. MOF-based materials, with tuneable pore properties and tailorable surface chemistry, and ease of handling, certainly deserve continued development into low-cost, efficient CO₂ sorbents for low-concentration CO₂ capture.

Structuration of Water in Microporous CAU-10-H under Gigapascal Pressure

Employing metal-organic frameworks (MOFs) as water adsorbents has become a flourishing field in recent years. Aluminum isophthalate [Al(OH)(bdc)]·nH₂O, referred to as CAU-10-H, is renowned for its high physical and chemical stability under external mechanical stimuli, which is crucial for use in sorption-based heat exchange. We report pressure-induced structural changes and water uptake/release of CAU-10-H in the gigapascal regime. CAU-10-H displays four different phases during pressurization in water up to 4.08(1) GPa. Upon immersion in water at ambient conditions, the unit cell volume expands by 1.3(1)%, by increasing water content from 78.7(1) to 85.6(1) H₂O per unit cell. Upon pressurization to 1.08(1) GPa, the water content increases gradually to 112.5(1) H₂O per unit cell and reduces the symmetry to P1 phase. At 1.72(1) GPa, a correlated "gate-opening/channel-closing" transition to a centrosymmetric Pnma phase occurs to increase the unit cell volume by 6.9(1)% and water content to 138.8(1) H₂O per unit cell. Further increase in pressure to 4.08(1) GPa then leads to a gradual decrease in water content to 119.2(1) H₂O per unit cell and redistribution of the inserted water molecules during a "gate-closing/channel-opening" transition to an I4₁/amd phase. After pressure removal, CAU-10-H reverts to its initial state in terms of crystallinity and water content. This pressure-induced water adsorption/desorption and concerted movements of gate-constraining ligands provides a detailed understanding of the water-MOF interplay, which can be used as a basis for designing new materials, possibly utilizing pressure as a tool for chemical modifications.

Towards High CO2 Conversions Using Cu/Zn Catalysts Supported on Aluminum Fumarate Metal-Organic Framework for Methanol Synthesis

Green methanol is a viable alternative for the storage of hydrogen and may be produced from captured anthropogenic sources of carbon dioxide. The latter was hydrogenated over Cu-ZnO catalysts supported on an aluminum fumarate metal-organic framework (AlFum MOF). The catalysts, prepared via slurry phase impregnation, were assessed for thermocatalytic hydrogenation of CO2 to methanol. PXRD, FTIR, and SBET exhibited a decrease in crystallinity of the AlFum MOF support after impregnation with Cu-Zn active sites. SEM, SEM-EDS, and TEM revealed that the morphology of the support is preserved after metal loading, where H2-TPR confirmed the presence of active sites for hydrogen uptake. The catalysts exhibited good activity, with a doubling in Cu and Zn loading over the AlFum MOF, resulting in a 4-fold increase in CO2 conversions from 10.8% to 45.6% and an increase in methanol productivity from 34.4 to 56.5 gMeOH/Kgcat/h. The catalysts exhibited comparatively high CO selectivity and high yields of H2O, thereby favoring the reverse water-gas shift reaction. The selectivity of the catalysts towards methanol was found to be 12.9% and 6.9%. The performance of the catalyst supported on AlFum MOF further highlights the potential use of MOFs as supports in the heterogeneous thermocatalytic conversion of CO2 to value-added products.

A scalable metal-organic framework as a durable physisorbent for carbon dioxide capture

[Figure: see text].

Understanding the Effects of Binders in Gas Sorption and Acidity of Aluminium Fumarate Extrudates

Understanding the impact of shaping processes on solid adsorbents is critical for the implementation of MOFs in industrial separation processes or as catalytic materials. Production of MOF‐containing shaped particles is typically associated with loss of porosity and modification of acid sites, two phenomena that affect their performance. Herein, we report a detailed study on how extrusion affects the crystallinity, porosity, and acidity of the aluminium fumarate MOF with clays or SiO₂ gel binders. Thorough characterization showed that the clay binders confer the extrudates a good mechanical robustness at the expense of porosity, while silica gel shows an opposite trend. The CO₂ selectivity towards CH₄, of interest for natural gas separation processes, is maintained upon the extrusion process. Moreover, probe FTIR spectroscopy revealed no major changes in the types of acid sites. This study highlights that these abundant and inexpensive clay materials may be used for scaling MOFs as active adsorbents.

Understanding the Effect of Water on CO2 Adsorption

Carbon capture from large sources and ambient air is one of the most promising strategies to curb the deleterious effect of greenhouse gases. Among different technologies, CO₂ adsorption has drawn widespread attention mostly because of its low energy requirements. Considering that water vapor is a ubiquitous component in air and almost all CO₂-rich industrial gas streams, understanding its impact on CO₂ adsorption is of critical importance. Owing to the large diversity of adsorbents, water plays many different roles from a severe inhibitor of CO₂ adsorption to an excellent promoter. Water may also increase the rate of CO₂ capture or have the opposite effect. In the presence of amine-containing adsorbents, water is even necessary for their long-term stability. The current contribution is a comprehensive review of the effects of water whether in the gas feed or as adsorbent moisture on CO₂ adsorption. For convenience, we discuss the effect of water vapor on CO₂ adsorption over four broadly defined groups of materials separately, namely (i) physical adsorbents, including carbons, zeolites and MOFs, (ii) amine-functionalized adsorbents, and (iii) reactive adsorbents, including metal carbonates and oxides. For each category, the effects of humidity level on CO₂ uptake, selectivity, and adsorption kinetics under different operational conditions are discussed. Whenever possible, findings from different sources are compared, paying particular attention to both similarities and inconsistencies. For completeness, the effect of water on membrane CO₂ separation is also discussed, albeit briefly.

Type 3 porous liquids based on non-ionic liquid phases - a broad and tailorable platform of selective, fluid gas sorbents

We describe a series of Type 3 porous liquids, denoted "T3PLs", based on a wide range of microporous solids including MOFs, zeolites and a porous organic polymer (PAF-1). These solids are dispersed in various non-ionic liquid phases (including silicone oils, triglyceride oils, and polyethylene glycols) which have a range of structures and properties, and that are in many cases sterically excluded from the pores of the solids. Several stable dispersions with high gas uptakes are obtained. We show how these dispersions can be tailored toward important gas separation processes (CO2/CH4, C2H4/C2H6) and applications that require biocompatibility.

Halogen Functionalization of Aluminium Fumarate Metal–Organic Framework via In Situ Hydrochlorination of Acetylenedicarboxylic Acid

The successful chloro-functionalization of aluminium fumarate (MIL-53-Fum) was achieved by in situ hydrochlorination of acetylenedicarboxylic acid on reaction with aluminium chloride resulting in the formation of the aluminium chlorofumarate metal–organic framework (MIL-53-Fum-Cl=[Al(OH)(Fum-Cl)]) in a one-pot reaction. The chloro functional groups decorating the pores enhance gas (CO2, CH4, and H2) sorption capacities and affinity compared with the non-functionalized MIL-53-Fum. The functionalization also results in a 2-fold increase in the selective adsorption of CO2 over CH4 compared with MIL-53-Fum.

Robust synthesis routes and porosity of the Al-based metal–organic frameworks Al-fumarate, CAU-10-H and MIL-160

We confirm that the investigated Al-MOFs are robust with respect to reproducible synthesis and concomitant porosity as a prerequisite for applications.

Welcoming Gallium- and Indium-Fumarate MOFs to the Family: Synthesis, Comprehensive Characterization, Observation of Porous Hydrophobicity, and CO2 Dynamics

The properties and applications of metal-organic frameworks (MOFs) are strongly dependent on the nature of the metals and linkers, along with the specific conditions employed during synthesis. Al-fumarate, trademarked as Basolite A520, is a porous MOF that incorporates aluminum centers along with fumarate linkers and is a promising material for applications involving adsorption of gases such as CO₂. In this work, the solvothermal synthesis and detailed characterization of the gallium- and indium-fumarate MOFs (Ga-fumarate, In-fumarate) are described. Using a combination of powder X-ray diffraction, Rietveld refinements, solid-state NMR spectroscopy, IR spectroscopy, and thermogravimetric analysis, the topologies of Ga-fumarate and In-fumarate are revealed to be analogous to Al-fumarate. Ultra-wideline ⁶⁹Ga, ⁷¹Ga, and ¹¹⁵In NMR experiments at 21.1 T strongly support our refined structure. Adsorption isotherms show that the Al-, Ga-, and In-fumarate MOFs all exhibit an affinity for CO₂, with Al-fumarate being the superior adsorbent at 1 bar and 273 K. Static direct excitation and cross-polarized ¹³C NMR experiments permit investigation of CO₂ adsorption locations, binding strengths, motional rates, and motional angles that are critical to increasing adsorption capacity and selectivity in these materials. Conducting the synthesis of the indium-based framework in methanol demonstrates a simple route to introduce porous hydrophobicity into a MIL-53-type framework by incorporation of metal-bridging -OCH₃ groups in the MOF pores.

Linking defects, hierarchical porosity generation and desalination performance in metal-organic frameworks

The composite membranes with defective metal–organic frameworks (MOFs) show a significant increase in water flux, without compromising the high salt rejection.

Composite membranes with defective metal–organic frameworks (MOFs) connect the emerging fields of MOF topological modification, MOF-polymer interfacial engineering and composite material functionalization. Although defective MOFs can be fabricated via thermal or chemical treatment, the relationship between hierarchical MOF structure and their performance in a polymeric membrane matrix has so far not been investigated. Here we show how a modulator fumarate-based MIL-53(Al) microwave synthesis process results in defective MOFs. This ligand replacement process leads to materials with hierarchical porosity, which creates a higher mesopore volume and Brønsted acidity without compromising the crystalline structure and pH stability. Compared with stoichiometric ratios, increasing the reaction time leads to more effective defect generation. The subsequent incorporation of defective MOFs into polyvinyl alcohol pervaporation membranes can effectively promote the fresh water productivity in concentrated brine treatment, with salt rejection of >99.999%. The membranes also have good long-term operational stability with effective antifouling behavior. We provide evidence that topological engineering of the MOF surface is related to their physical and chemical behaviors in a polymeric matrix, opening up the possibility of MOF defect engineering to realize selective separations, catalysis and sensing within a polymeric matrix.

Preparation of a Cu(BTC)-rGO catalyst loaded on a Pt deposited Cu foam cathode to reduce CO2 in a photoelectrochemical cell

To increase the reaction productivity and selectivity of the CO₂ photoelectrochemical reduction reaction, a Cu (benzene 1,3,5-tricarboxylic acid [BTC])-reduced graphite oxide (rGO) catalyst was prepared by using a facile hydrothermal method and used in a CO₂ photoelectrochemical cell (PEC) as a cathode catalyst. Characterization of the catalyst proved that successfully bonding of rGO to Cu(BTC) not only facilitated faster transfer of electrons on the surface of the catalyst but also created more active sites. CO₂ photoelectrochemical reduction experimental results showed that the total carbon atom conversion rate was up to 3256 nmol h⁻¹ cm⁻² which was much higher than when pure Cu(BTC) was used as a cathode catalyst. The liquid product's selectivity to alcohols was up to 95% when −2 V voltage was applied to the system with Cu(BTC)-rGO used as the cathode catalyst.

Schematic of a photoelectrochemical cell for CO₂ reduction: the H⁺ generation process and the CO₂ process run in two separated chambers respectively.

Metal–organic framework based micro solid phase extraction coupled with supramolecular solvent microextraction to determine copper in water and food samples

D-μ-SPE-SUPRAS-ME followed by GFAAS was successfully used for preconcentration and determination of copper in real samples.

Potential of ultramicroporous metal–organic frameworks in CO2 clean-up

This article explains the need for energy-efficient large-scale CO₂ capture and briefly mentions the requirements for optimal solid sorbents for this application.

CO2 Capture and Separations Using MOFs: Computational and Experimental Studies

This Review focuses on research oriented toward elucidation of the various aspects that determine adsorption of CO₂ in metal-organic frameworks and its separation from gas mixtures found in industrial processes. It includes theoretical, experimental, and combined approaches able to characterize the materials, investigate the adsorption/desorption/reaction properties of the adsorbates inside such environments, screen and design new materials, and analyze additional factors such as material regenerability, stability, effects of impurities, and cost among several factors that influence the effectiveness of the separations. CO₂ adsorption, separations, and membranes are reviewed followed by an analysis of the effects of stability, impurities, and process operation conditions on practical applications.

Gate-opening upon CO2 adsorption on a metal–organic framework that mimics a natural stimuli-response system

A dynamic d-champhorate-based protuberant-grid-type framework, undergoes gate opening and closing processes that were triggered by the stimuli of the adsorption or desorption of CO₂. It is able to specifically recognize CO₂ over than N₂ and H₂ and shows a high CO₂ uptake of 90 mg g⁻¹ under 35 bar at 298 K.

Trypsin purification using magnetic particles of azocasein-iron composite

This work presents an inexpensive, simple and fast procedure to purify trypsin based on affinity binding with ferromagnetic particles of azocasein composite (mAzo). Crude extract was obtained from intestines of fish Nile tilapia (Oreochromis niloticus) homogenized in buffer (01g tissue/ml). This extract was exposed to 100mg of mAzo and washed to remove unbound proteins by magnetic field. Trypsin was leached off under high ionic strength (3M NaCl). Preparation was achieved containing specific activity about 60 times higher than that of the crude extract. SDS-PAGE showed that the purified protein had molecular weight (24kDa) in concordance with the literature for the Nile tilapia trypsin. The mAzo composite can be reused and applied to purify trypsin from other sources.