Carboxymethylated Cellulose Fibers as Low-Cost and Renewable Adsorbent Materials

Nano-copper ions assembled cellulose-based composite with antibacterial activity for biodegradable personal protective mask

The current SARS-CoV-2 pandemic has resulted in the widespread use of personal protective equipment, particularly face masks. However, the use of commercial disposable face masks puts great pressure on the environment. In this study, nano-copper ions assembled cotton fabric used in face masks to impart antibacterial activity has been discussed. To produce the nanocomposite, the cotton fabric was modified by sodium chloroacetate after its mercerization, and assembled with bactericidal nano-copper ions (about 10.61 mg·g-1) through electrostatic adsorption. It demonstrated excellent antibacterial activity against Staphylococcus aureus and Escherichia coli because the gaps between fibers in the cotton fabric allow the nano-copper ions to be fully released. Moreover, the antibacterial efficiency was maintained even after 50 washing cycles. Furthermore, the face mask constructed with this novel nanocomposite upper layer exhibited a high particle filtration efficiency (96.08% ± 0.91%) without compromising the air permeability (28.9 min·L-1). This green, economical, facile, and scalable process of depositing nano-copper ions onto modified cotton fibric has great potential to reduce disease transmission, resource consumption, and environmental impact of waste, while also expanding the range of protective fabrics.

Phytic Acid Doped Polyaniline as a Binding Coating Promoting Growth of Prussian Blue on Cotton Fibers for Adsorption of Copper Ions

In recent years, the elimination of heavy metals from wastewater has become an important topic due to rapid industrialization, and it is of considerable interest to develop renewable and degradable materials for this purpose. In this work, a novel Prussian blue/polyaniline@cotton fibers (PB/PANI@CFs) composite was fabricated by a two-step process. Phytic acid doped PANI as a binding coating greatly promoted both the growth of PB and the adsorption of Cu2+. The deposition ratio of PB was as high as 24.68%. Scanning electron microscopy (SEM) displayed that PB nanoparticles were grown more uniformly in the composite and formed a perfect nanocube structure compared with PB@CFs. The successful deposition of both PB and PANI on CFs was demonstrated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FITR), and X-ray photoelectron spectroscopy (XPS). The effect of adsorption time, adsorbent dose, initial pH value, and initial copper sulphate concentration on the adsorption of PB/PANI@CFs composite for Cu2+ was studied by static adsorption and was compared with those of PANI@CFs and PB@CFs. The results showed that the maximum removal efficiency of Cu2+ by PB/PANI@CFs can reach 93.4% within 5 h, and the maximum adsorption capacity of Cu2+ can reach 31.93 mg·g−1. The adsorption of Cu2+ on PB/PANI@CFs followed the pseudo-second order kinetic model and conformed to the Freundlich adsorption isothermal model. The PB-functionalized CFs provided new insights into the design of efficient and low-cost absorbents for heavy metal remediation. The proposed process solves two problems simultaneously, i.e., the utilization of environmentally friendly and biodegradable biomass resources and the adsorption of heavy metal ions, and is a good approach to achieve high-quality and sustainable development.

Hybrid "Kill and Release" Antibacterial Cellulose Papers Obtained via Surface-Initiated Atom Transfer Radical Polymerization

Infectious diseases triggered by bacteria cause a severe risk to human health. To counter this issue, surfaces coated with antibacterial materials have been widely used in daily life to kill these bacteria. The substrates enabled with a hybrid kill and release strategy can be employed not only to kill the bacteria but also to wash them using external stimuli (temperature, pH, etc.). Utilizing this concept, we develop thermoresponsive antibacterial-cellulose papers to exhibit hybrid kill and release properties. Thermoresponsive copolymers [p(NIPAAm-co-AEMA)] are grafted on cellulose papers using a surface-initiated atom transfer radical polymerization approach for bacterial debris release. Later for antibacterial properties, silver nanoparticles (AgNPs) are immobilized on thermoresponsive copolymer-grafted cellulose papers using electrostatic interactions. We confirm the thermoresponsive copolymer grafting and AgNP coating by attenuated total reflection Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. Thermoresponsiveness and reusability of the modified cellulose papers are confirmed through water contact angle measurements. The interaction potency between AgNPs and modified cellulose is validated by inductively coupled plasma atomic emission spectroscopy analysis. Gram-negative bacteria Escherichia coli (E. coli DH5-α) is used to demonstrate antibacterial hybrid kill and release performance. Agar-diffusion testing demonstrates the antibacterial nature of the modified cellulose papers. The fluorescence micrograph reveals that modified cellulose papers can effectively release almost all the dead bacterial debris from their surfaces after thermal stimulus wash. The modified cellulose paper surfaces are expected to have wide applications in the field of exploring more antibacterial and smart surfaces.

Plant active products and emerging interventions in water potabilisation: disinfection and multi-drug resistant pathogen treatment

Background

This review aims at establishing the emerging applications of phytobiotics in water treatment and disinfection.

Results

Statistical analysis of data obtained revealed that the use of plant product in water treatment needs more research attention. A major observation is that plants possess multifaceted components and can be sustainably developed into products for water treatment. The seed (24.53%), flower (20.75), leaf (16.98%) and fruit (11.32%) biomasses are preferred against bulb (3.77%), resin (1.89%), bark (1.89%) and tuber (1.89%). The observation suggests that novel applications of plant in water treatment need further exploration since vast and broader antimicrobial activities (63.63%) is reported than water treatment application (36.37%).

Conclusions

This review has revealed the existing knowledge gaps in exploration of plant resources for water treatment and product development. Chemical complexity of some plant extracts, lack of standardisation, slow working rate, poor water solubility, extraction and purification complexities are limitations that need to be overcome for industrial adoption of phytochemicals in water treatment. The field of phytobiotics should engage modern methodologies such as proteomics, genomics, and metabolomics to minimise challenges confronting phytobiotic standardisation. The knowledge disseminated awaits novel application for plant product development in water treatment.

One-pot synthesis of mercapto functionalized Zr-MOFs for the enhanced removal of Hg2+ ions from water

A new one-pot approach was developed for the synthesis of mercapto functionalized Zr-MOFs with high adsorption capacity for Hg²⁺ ions.