Adsorption Equilibrium and Kinetics of Nitrogen, Methane and Carbon Dioxide Gases onto ZIF-8, Cu10%/ZIF-8, and Cu30%/ZIF-8

Low-Hydrophilic HKUST-1/Polymer Extrudates for the PSA Separation of CO2/CH4

HKUST-1 is an MOF adsorbent industrially produced in powder form and thus requires a post-shaping process for use as an adsorbent in fixed-bed separation processes. HKUST-1 is also sensitive to moisture, which degrades its crystalline structure. In this work, HKUST-1, in the form of crystalline powder, was extruded into pellets using a hydrophobic polymeric binder to improve its moisture stability. Thermoplastic polyurethane (TPU) was used for that purpose. The subsequent HKUST-1/TPU extrudate was then compared to HKUST-1/PLA extrudates synthesized with more hydrophilic polymer: polylactic acid (PLA), as the binder. The characterization of the composites was determined via XRD, TGA, SEM-EDS, and an N2 adsorption isotherm analysis. Meanwhile, the gas-separation performances of HKUST-1/TPU were investigated and compared with HKUST-1/PLA from measurements of CO2 and CH4 isotherms at three different temperatures, up to 10 bars. Lastly, the moisture stability of the composite materials was investigated via an aging analysis during storage under humid conditions. It is shown that HKUST-1's crystalline structure was preserved in the HKUST-1/TPU extrudates. The composites also exhibited good thermal stability under 523 K, whilst their textural properties were not significantly modified compared with the pristine HKUST-1. Furthermore, both extrudates exhibited larger CO2 and CH4 adsorption capacities in comparison to the pristine HKUST-1. After three months of storage under atmospheric humid conditions, CO2 adsorption capacities were reduced to only 10% for HKUST-1/TPU, whereas reductions of about 25% and 54% were observed for HKUST-1/PLA and the pristine HKUST-1, respectively. This study demonstrates the interest in shaping MOF powders by extrusion using a hydrophobic thermoplastic binder to operate adsorbents with enhanced moisture stability in gas-separation columns.

Investigation of palladium catalysts in mesoporous silica support for CO oxidation and CO2 adsorption

The oxidation of Carbon monoxide (CO) to Carbon dioxide (CO2) is one of the most extensively investigated reactions in the field of heterogeneous catalysis, and it occurs via molecular rearrangements induced by catalytic metal atoms with oxygen intermediates. CO oxidation and CO2 capture are instrumental processes in the reduction of green-house gas emissions, both of which are used in low-temperature CO oxidation in the catalytic converters of vehicles. CO oxidation and CO2 adsorption at different temperatures are evaluated for palladium-supported silica aerogel (Pd/SiO2). The synthesized catalyst was active and stable for low-temperature CO oxidation. The catalytic activity was enhanced after the first cycle due to the reconditioning of the catalyst's pores. It was found that the presence of oxide forms of palladium in the SiO2 microstructure, influences the performance of the catalysts due to oxygen vacancies that increases the frequency of active sites. CO2 gas adsorption onto Pd/SiO2 was investigated at a wide-ranging temperature from 16 to 120 °C and pressures ∼1 MPa as determined from the isotherms that were evaluated, where CO2 showed the highest equilibrium adsorption capacity at 16 °C. The Langmuir model was employed to study the equilibrium adsorption behavior. Finally, the effect of moisture on CO oxidation and CO2 adsorption was considered to account for usage in real-world applications. Overall, mesoporous Pd/SiO2 aerogel shows potential as a material capable of removing CO from the environment and capturing CO2 at low temperatures.

Assembling CeO2 nanoparticles on ZIF-8 via the hydrothermal method to promote the CO2 photoreduction performance

Photocatalytic reduction of CO₂ to valuable carbon fuel is a prospective technique to decrease CO₂ emissions and simultaneously generate efficient chemical energy. In this paper, a novel high-efficiency photocatalyst ZIF-8@CeO₂ heterogeneous composite (ZIF = zeolitic imidazolate framework) was prepared by the hydrothermal method, where CeO₂ nanospheres were uniformly grown on the surface of ZIF-8. Compared to pristine ZIF-8 or CeO₂ nanoparticles (NPs), the ZIF-8@CeO₂ composite shows significantly better efficiency in the reduction of CO₂ into CO and CH₄ under light irradiation, that is the CO evolution rate can reach 465.01 μmol g^-1 h^-1 and the CH₄ evolution rate can reach 181.27 μmol g^-1 h^-1. Analyses indicated that the addition of CeO₂ in the composites will expand the photoresponse region; the formation of the ZIF-8/CeO₂ heterojunction significantly promoted the separation of photogenerated electron-hole pairs within the composite. This work provided an effective method to further improve the catalytic activity of ZIF-based materials, which paved a new way for eco-friendly conversion of carbon dioxide into clean fuels and they could also have huge potential for application in energy and environmental science.

Sodium Alginate-Based Carbon Aerogel-Supported ZIF-8-Derived Porous Carbon as an Effective Adsorbent for Methane Gas

Adsorption natural gas (ANG) is a technology in which natural gas is stored on the surface of porous materials at relatively low pressures, which are promising candidates for adsorption of natural gas. Adsorbent materials with a large surface area and porous structure plays a significant role in the ANG technology, which holds promise in increasing the storage density for natural gas while decreasing the operating pressure. Here, we demonstrate a facile synthetic method for rational construction of a sodium alginate (SA)/ZIF-8 composite carbon aerogel (AZSCA) by incorporating ZIF-8 particles into SA aerogel through a directional freeze-drying method followed by the carbonization process. The structure characterization shows that AZSCA has a hierarchical porous structure, in which the micropores originated from MOF while the mesopores are derived from the three-dimensional network of the aerogel. The experimental results show that AZSCA achieved high methane adsorption of 181 cm³·g^-1 at 65 bar and 298 K, along with higher isosteric heat of adsorption (Q_st) throughout the adsorption range. Thus, the combination of MOF powders with aerogel can find potential applications in other gas adsorption.

Methane Oxidation to Methanol

The direct transformation of methane to methanol remains a significant challenge for operation at a larger scale. Central to this challenge is the low reactivity of methane at conditions that can facilitate product recovery. This review discusses the issue through examination of several promising routes to methanol and an evaluation of performance targets that are required to develop the process at scale. We explore the methods currently used, the emergence of active heterogeneous catalysts and their design and reaction mechanisms and provide a critical perspective on future operation. Initial experiments are discussed where identification of gas phase radical chemistry limited further development by this approach. Subsequently, a new class of catalytic materials based on natural systems such as iron or copper containing zeolites were explored at milder conditions. The key issues of these technologies are low methane conversion and often significant overoxidation of products. Despite this, interest remains high in this reaction and the wider appeal of an effective route to key products from C-H activation, particularly with the need to transition to net carbon zero with new routes from renewable methane sources is exciting.

Copper-doped zeolitic imidazolate frameworks-8/hydroxyapatite composite coating endows magnesium alloy with excellent corrosion resistance, antibacterial ability and biocompatibility

Magnesium (Mg) and its alloys exhibit an excellent prospect for orthopedic clinical application due to their outstanding biodegradability and mechanical adaptability. However, the rapid corrosion rate/latent device-associated infections may lead to a failed internal fixation of Mg-based implants. Herein, a novel composite coating consisted of outer copper-doped zeolitic imidazolate frameworks-8 and inner hydroxyapatite (Cu@ZIF-8/HA) was in situ constructed on AZ31B Mg alloy via a two-step approach of hydrothermal treatment and seeded solvothermal method. The results verified that the electrochemical impedance of the obtained Cu45@ZIF-8/HA composite coating increased by two orders of magnitude to 6.6013 × 104 Ω·cm2 compared to that of bare Mg alloy. This was attributed to the reduced particle size of ZIF-8 nanoparticles due to the doped copper ions, which could be effectively grown in situ on the micro-nano flower-like structure of the HA-coated Mg alloy. Meanwhile, the Cu@ZIF-8/HA coating exhibited excellent antibacterial properties due to the release of copper ions and zinc ions from Cu@ZIF-8 dissolved in bacterial culture solution. The ICP results unraveled that the released concentration of copper and zinc ions could enhance the activity of alkaline phosphatase in the appropriate range during MC3T3-E1 cell culture in vitro for 7 days. This research revealed that the preparation of multifunctional metal-organic frameworks coating doped with antimicrobial metal ions via the seed layer solvothermal method was significant for studying the antimicrobial properties, osteogenic performance and corrosion resistance of Mg-based bioactive coatings.

Metal-Organic-Framework Based Functional Materials for Uranium Recovery: Performance Optimization and Structure/Functionality-Activity Relationships

Uranium recovery has profound significance in both uranium resource acquisition and pollution treatment. In recent years, metal-organic frameworks (MOFs) have attracted much attention as potential uranium adsorbents owing to their tunable structural topology and designable functionalities. This review explores the research progress in representative classic MOFs (MIL-101, UiO-66, ZIF-8/ZIF-67) and other advanced MOF-based materials for efficient uranium extraction in aqueous or seawater environments. The uranium uptake mechanism of the MOF-based materials is refined, and the structure/functionality-property relationship is further systematically elucidated. By summarizing the typical functionalization and structure design methods, the performance improvement strategies for MOF-based adsorbents are emphasized. Finally, the present challenges and potential opportunities are proposed for the breakthrough of high-performance MOF-based materials in uranium extraction.