Superhydrophobic Polydimethylsiloxane@Multiwalled Carbon Nanotubes Membrane for Effective Water-in-Oil Emulsions Separation and Quick Deicing

Preparation and properties of oxidized multi-walled carbon nanotube superhydrophobic composites modified by bio-fatty acids

In this paper, a preparation method of superhydrophobic composites of oxidized multi-walled carbon nanotubes modified by stearic acid (SA) is proposed. Hydroxylated multi-walled carbon nanotubes (HMWCNTs) were obtained by oxidizing multi-walled carbon nanotubes with potassium dichromate to give them hydroxyl groups on the surface. Subsequently, the carboxyl group in the SA molecule was esterified with the hydroxyl group on the HMWCNTs. SA molecules were grafted onto the surface of multi-walled carbon nanotubes. SA modified oxidized multi-walled carbon nanotubes (SMWCNT) superhydrophobic composites were obtained. The results show that the water contact angle (WCA) of superhydrophobic composites can reach up to 174°. At the same time, the modified nanocomposites have good anti-icing and corrosion resistance. After low temperature delayed freezing test, the freezing extension time of the nanocomposite film is 30 times that of the smooth surface. Under strong acid and alkali conditions, the superhydrophobic nanocomposites still maintain good superhydrophobicity. The nanocomposites may have potential applications in the preparation of large-scale superhydrophobic coatings.

Mechanically-robust electrospun nanocomposite fiber membranes for oil and water separation

Mechanically-robust nanocomposite membranes have been developed via crosslinking chemistry and electrospinning technique based on the rational selection of dispersed phase materials with high Young's modulus (i.e., graphene and multiwalled carbon nanotubes) and Cassie-Baxter design and used for oil and water separation. Proper selection of dispersed phase materials can enhance the stiffness of nanocomposite fiber membranes while their length has to be larger than their critical length. Chemical modification of the dispersed phase materials with fluorochemcials and their induced roughness were critical to achieve superhydrophobocity. Surface analytic tools including goniometer, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, atomic force microscopy (AFM) and scanning electron microscope (SEM) were applied to characterize the superhydrophobic nanocomposite membranes. An AFM-based nanoindentation technique was used to measure quantitativly the stiffness of the nanocomposite membranes for local region and whole composites, compared with the results by a tensile test technique. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques were used to confirm composition and formation of nanocomposite membranes. These membranes demonstrated excellent oil/water separation. This work has potential application in the field of water purification and remediation.

Efficient Fabrication of Carbon Nanotube-Based Stretchable Electrodes for Flexible Electronic Devices

Stretchable electrodes are highly demanded in various wearable and flexible electronic devices, whereas the efficient fabrication approach is still a challenge. In this work, an efficient shrinking method to fabricate carbon nanotube (CNT)-based stretchable electrodes is proposed. The electrode is a layer of anisotropic CNT wrinkling film coated on a latex balloon substrate (CNT@latex), whose resistivity remains stable after 25 000 stretching cycles of 0 to 50% tensile strain, and can survive up to 500% tensile train. The highly conductive electrode can be used as the current collector of a stretchable Zinc-ion battery, maintaining an output voltage of 1.3 V during the stretching process of 0 to 100%. The applications of the electrode in flexible triboelectric nanogenerators and Joule heating devices are also demonstrated, further indicating their good prospects in the field of stretchable electronic devices.

A Nanofibrillated Cellulose-Based Electrothermal Aerogel Constructed with Carbon Nanotubes and Graphene

Nanofibrillated cellulose (NFC) as an environmentally friendly substrate material has superiority for flexible electrothermal composite, while there is currently no research on porous NFC based electrothermal aerogel. Therefore, this work used NFC as a skeleton, combined with multi-walled carbon nanotubes (MWCNTs) and graphene (GP), to prepare NFC/MWCNTs/GP aerogel (CCGA) via a simple and economic freeze-drying method. The electrothermal CCGA was finally assembled after connecting CCGA with electrodes. The results show that when the concentration of the NFC/MWCNTs/GP suspension was 5 mg mL^-1 and NFC amount was 80 wt.%, the maximum steady-state temperature rise of electrothermal CCGA at 3000 W m^-2 and 2000 W m^-2 was of about 62.0 °C and 40.4 °C, respectively. The resistance change rate of the CCGA was nearly 15% at the concentration of 7 mg mL^-1 under the power density of 2000 W m^-2. The formed three-dimensional porous structure is conducive to the heat exchange. Consequently, the electrothermal CCGA can be used as a potential lightweight substrate for efficient electrothermal devices.

Three-Dimensionally Printed Bioinspired Superhydrophobic Packings for Oil-in-Water Emulsion Separation

The separation of oil-water emulsions has attracted considerable attention in recent years. The main challenge is to find new cost-effective ways to develop a separation technology that has the potential for scaling up treatment. In this study, benefitting from the idea in traditional chemical engineering processes, we report on three-dimensionally printed superhydrophobic poly(lactic acid) (PLA) packings for oil-in-water emulsion separation. Superhydrophobicity was achieved through a bioinspired modification process including selective solvent etching and nanoparticle decoration. The obtained superhydrophobic PLA packing has an air-water contact angle of 150° and a water adhesion force of 22 μN. A maximum separation efficiency of 95% was achieved while retaining a relatively high flux of 7.5 kL m^-2 h^-1 by tailoring the internal geometry. Our approach demonstrates a promising method to fabricate packings with user-defined and functional features. The relatively low-cost and efficient fabrication process is beneficial in industrial applications.