Fluidic Oscillator as a Continuous Crystallizer: Feasibility Evaluation

Development of long-acting injectable suspensions by continuous antisolvent crystallization: An integrated bottom-up process

Our present work elucidated the operational feasibility of direct generation and stabilization of long-acting injectable (LAI) suspensions of a practically insoluble drug, itraconazole (ITZ), by combining continuous liquid antisolvent crystallization with downstream processing (i.e., centrifugal filtration and reconstitution). A novel microchannel reactor-based bottom-up crystallization setup was assembled and optimized for the continuous production of micro-suspension. Based upon the solvent screening and solubility study, N-methyl pyrrolidone (NMP) was selected as the optimal solvent and an impinging jet Y-shaped microchannel reactor (MCR) was selected as the fluidic device to provide a reproducible homogenous mixing environment. Operating parameters such as solvent to antisolvent ratio (S/AS), total jet liquid flow rates (TFRs), ITZ feed solution concentration and the maturation time in spiral tubing were tailored to 1:9 v/v, 50 mL/min, 10 g/100 g solution, and 96 h, respectively. Vitamin E TPGS (0.5% w/w) was found to be the most suitable excipient to stabilize ITZ particles amongst 14 commonly used stabilizers screened. The effect of scaling up from 25 mL to 15 L was evaluated effectively with in situ monitoring of particle size distribution (PSD) and solid-state form. Thereafter, the suspension was subjected to centrifugal filtration to remove excess solvent and increase ITZ solid fraction. As an alternative, an even more concentrated wet pellet was reconstituted with an aqueous solution of 0.5% w/w Vitamin E TPGS as resuspending agent. The ITZ LAI suspension (of 300 mg/mL solid concentration) has the optimal PSD with a D10 of 1.1 ± 0.3 µm, a D50 of 3.53 ± 0.4 µm and a D90 of 6.5 ± 0.8 µm, corroborated by scanning electron microscopy (SEM), as remained stable after 548 days of storage at 25 °C. Finally, in vitro release methods using Dialyzer, dialysis membrane sac were investigated for evaluation of dissolution of ITZ LAI suspensions. The framework presented in this manuscript provides a useful guidance for development of LAI suspensions by an integrated bottom-up approach using ITZ as model API.

Flow Physics of Planar Bistable Fluidic Oscillator with Backflow Limbs

Fluidic oscillators (FOs) are used in a variety of applications, including process control and process intensification. Despite the simple design and operation of FOs, the fluid dynamics of FOs exhibit rich complexities. The inherently unstable flow, jet oscillations, and resulting vortices influence mixing and other transport processes. In this work, we computationally investigated the fluid dynamics of a new design of a planar FO with backflow limbs. The design comprised of two symmetric backflow limbs leading to bistable flow. The unsteady flow dynamics, internal recirculation, jet oscillations, secondary flow vortices were computationally studied over a range of inlet Reynolds numbers (2400-12,000). The nature and frequency of the jet oscillations were quantified. The computed jet oscillation frequency was compared with the experimentally measured (using imaging techniques) jet oscillation frequency. The flow model was then used to quantitatively understand mixing, heat transfer, and residence time distribution. The approach and the results presented in this work will provide a basis for designing FO's with desired flow and transport characteristics for various engineering applications.

Optimal Operation of an Oscillatory Flow Crystallizer: Coupling Disturbance and Stability

In the process of industrial crystallization, it is always difficult to balance the secondary nucleation rate and metastable zone width (MSZW). Herein, we report an experimental and numerical study for the cooling crystallization of paracetamol in an oscillatory flow crystallizer (OFC), finding the optimal operating conditions for balancing the secondary nucleation rate and MSZW. The results show that the MSZW decreases with the increase of oscillation Reynolds number (Re _o). Compared to the traditional stirring system, the OFC has an MSZW three times larger than that of the stirring system under a similar power density of consumption. With the numerical simulation, the OFC can produce a stable space environment and instantaneous strong disturbance, which is conducive to the crystallization process. Above all, a high Re _o is favorable to produce a sufficient nucleation rate, which may inevitably constrict the MSZW to a certain degree. Then, the optimization strategy of the operating parameter (Re _o) in the OFC is proposed.