pH-Controlled Assembly of Five New Organophosphorus Strandberg-Type Cluster-Based Coordination Polymers for Enhanced Electrochemical Capacitor Performance

Facile design of FeCu metal-organic frameworks anchored on layer Ti3C2Tx MXene for high-performance electrochemical sensing of resorcinol

This work reports the rational design of a composite material by growing FeCu-MOF-919 on the surface of layered Ti3C2Tx MXene. The introduction of Ti3C2Tx MXene simultaneously weakens the aggregation of FeCu-MOF-919 and Ti3C2Tx MXene, which increases the electrochemical reaction active site of the composite material and improves the electrochemical activity. Interestingly, the FeCu-MOF-919/Ti3C2Tx based sensors were used to detect resorcinol (RS) with a wide linear range (0.5-152.5 μM), excellent sensitivity (0.23 μA μM-1 cm-2), low limit of detection (LOD = 0.08 μM) and outstanding stability. Meanwhile, the sensor shows high repeatability of 1.07 % RSD, reproducibility of 1.47 % RSD and anti-interference performance. What's more, the sensor can be successfully used to detect RS in tap water with good recoveries (96.25-103.37 %, RSD ≤2.18 %), demonstrating that the FeCu-MOF-919/Ti3C2Tx exhibits significant potential as an advanced sensing apparatus for the surveillance of RS in the natural environment.

Four polyoxomolybdated-based 3D compounds as supercapacitors and amperometric sensors

Four polyoxomolybdated compounds based on Tetp (Tetp = 4-[4-(2-Thiophen-2-yl-ethyl)-4H-[1, 2, 4]triazole-3-yl]-pyridine), namely [Zn(Tetp)2(H2O)2][(β-Mo8O26)0.5] (Zn-Mo8), [Co(Tetp)2(H2O)2][(β-Mo8O26)0.5] (Co-Mo8), [Cu4(Tetp)6(H2O)2]{H3[K(H2O)3](θ-Mo8O26)(Mo12O40)}·8H2O (Cu-Mo20) and [Cu3(Tetp)3][PMo12O40]·H2O (Cu-PMo12) are synthesized by hydrothermal methods and are used as electrode materials for supercapacitors(SCs) and electrochemical sensors. Inserting polyoxometalates (POMs) with redox active sites into transition metal compounds (TMCs) can improve the internal ion/electron transfer rate, thus effectively enhancing the electrochemical performance. Compared with the parent POMs, four compounds exhibit excellent electrochemical properties. In particular, Cu-PMo12 shows an excellent specific capacitance (812.3 F g-1 at 1 A g-1) and stability (94.42%), as well as a wide detection range (0.05 to 1250 µM) and a low detection limit (0.057 µM) for NO2- sensing.

In-situ synthesized and induced vertical growth of cobalt vanadium layered double hydroxide on few-layered V2CTx MXene for high energy density supercapacitors

Two-dimensional (2D) MXene nanomaterials display great potential for green energy storage. However, as a result of self-stacking of MXene nanosheets and the presence of conventional binders, MXene-based nanomaterials are significantly hindered in their rate capability and cycling stability. We successfully constructed a self-supported stereo-structured composite (TMA-V2CTx/CoV-LDH/NF) by in-situ growing 2D cobalt vanadium layered double hydroxide (CoV-LDH) vertically on 2D few-layered V2CTx MXene nanosheets and interconnecting it with Ni foam (NF) with a self-supported structure to act as a binder-free electrode. In addition to inhibiting CoV-LDH aggregation, the highly conductive V2CTx MXene and CoV-LDH work synergistically to improve charge storage. The specific capacitance of the TMA-V2CTx/CoV-LDH/NF electrode is 2374 F/g (1187 C/g) at 1 A/g. At the same time, the TMA-V2CTx/CoV-LDH/NF exhibits excellent stability, retaining 85.3 % of its specific capacitance at 20 A/g after 10,000 cycles. In addition, the hybrid supercapacitor (HSC) is assembled based on positive electrode (TMA-V2CTx/CoV-LDH/NF) and negative electrode (AC), achieving the maximum energy density of 74.4 Wh kg-1 at 750.3 W kg-1. TMA-V2CTx/CoV-LDH/NF has potential as an electrode material for storing green energy. The research strategy provides a development prospect for the construction of novel V2CTx MXene-based electrode material with self-supported structures.

Defect engineering induces Mo-regulated Co9Se8/FeNiSe heterostructures with selenium vacancy for enhanced electrocatalytic overall water splitting in alkaline

The pursuit of cost-effective catalysts for electrocatalytic overall water splitting continues to present a significant challenge in the field. A molybdenum (Mo)-regulated Co9Se8/FeNiSe self-supporting electrode material with rich vacancy defects has been prepared by hydrothermal reaction. Doping of Mo atoms not only can form rich selenium vacancy defects to enrich the inherent activity of the catalyst, but also expose more active sites. The intrinsic electronic architecture of the interface catalysis is regulated and optimized through the introduction of heteroatom Mo, resulting in the exceptional catalytic activities of the Mo-Co9Se8/FeNiSe heterostructure. Additionally, the Faraday efficiency of hydrogen (H2) and oxygen (O2) production approaches 100 %. The voltage required for the water-splitting system is only 1.58 V (10 mA cm-2), and 100 h stability test at 100 mA cm-2 demonstrates no decay. This work presents a new perspective for the reasonable design and synthesis of non-precious metal selenide-based bifunctional electrocatalysts.

Constructing Two Cu-Modified Organophosphomolybdates from a Nanocluster to a One-Dimensional Chain for Boosted Visible-Light-Driven Hydrogen Production

Photocatalytic decomposition of water to produce hydrogen H2 is an ideal way to solve energy and environmental problems, and the development of highly efficient polyoxometalate catalysts for photocatalytic hydrogen production has attracted wide attention. Herein, two Cu-modified Strandberg-type organophosphomolybdates were successfully synthesized, [Cu(C8H7N3)(H2O)2]2[(C6H5PO3)2Mo5O15]·4H2O (1) and [Cu(phen)(H2O)][Cu(phen)(H2O)2][(C6H5PO3)2Mo5O15]·2H2O (2) ([(C6H5P)2Mo5O21]Cu2) (C8H7N3 = 2-(1H-pyrazol-3-yl)pyridine, phen = 1,10-phenanthroline). Two Strandberg-type organophosphomolybdates can be used for visible-light-driven hydrogen production. Also, compound 2 exhibits an H2 production rate of 6399 μmol g-1 h-1 after 8 h light exposure in the presence of photosensitization agent [Ir(dtbbpy)(ppy)2][PF6] and TEOA. In addition, cyclic tests showed that compound 2 could be recycled four times without a significant reduction in catalytic performance. This work offers fresh insight into the development of novel polyoxometalates for efficient hydrogen evolution.

Exploring The Synergistic Effect Of CoSeP/CoP Interface Catalyst For Efficient Urea Electrolysis

Electrocatalytic oxidation of urea (UOR) is a potential energy-saving hydrogen production technology that can replace oxygen evolution reaction (OER). Therefore, CoSeP/CoP interface catalyst is synthesized on nickel foam using hydrothermal, solvothermal, and in situ template methods. The strong interaction of tailored CoSeP/CoP interface promotes the hydrogen production performance of electrolytic urea. During the hydrogen evolution reaction (HER), the overpotential can reach 33.7 mV at 10 mA cm-2 . The cell voltage can reach 1.36 V at 10 mA cm-2 in the overall urea electrolytic process. Notably, the overall urine electrolysis performance of the catalyst in the human urine medium can reach 1.40 V at 10 mA cm-2 and can exhibit durable cycle stability at 100 mA cm-2 . Density functional theory (DFT) proves that the CoSeP/CoP interface catalyst can better adsorb and stabilize reaction intermediates CO* and NH* on its surface through a strong synergistic effect, thus enhancing the catalytic activity.

A sensing platform based on Cu-MOF encapsulated Dawson-type polyoxometalate crystal material for electrochemical detection of xanthine

A promising sensing platform based on polyoxometalate-based metal-organic framework (POMOF) was established for sensitive electrochemical detection of xanthine (XA). In the unique structure of POMOF, the Dawson polyoxoanions P₂W₁₈ were encapsulated into 3D open copper-mixed ligand nanotube framework Cu-MOF, in which the cavity of the metal-organic framework provides a specific shelter to prevent the aggregation and loss of polyoxometalate in electrocatalytic reactions; meanwhile, unsaturated Cu(II) active sites of Cu-MOF can also serve as electrocatalytic active center. The POMOF-based sensor (CuMOFP₂W₁₈/XC-72R) was fabricated by using acetylene black (XC-72R) as a support material to enhance the conductivity of POMOF. The performances of the POMOF-based sensor were studied by using different electrochemical testing methods. The composite displayed remarkable electrocatalytic activity for the oxidation of XA due to the synergistic effect of polyoxometalate (POM) and metal-organic framework (MOF). The electrochemical sensor demonstrated a wide linear range (0.5 μM-240 μM), low detection limit (0.26 μM), and excellent selectivity for detecting XA. Furthermore, the composite further demonstrated excellent reproducibility and great stability. More importantly, the proposed sensor was utilized to detect XA in real samples, which may provide a new way for early disease diagnosis.

Two Polyoxometalate-Encapsulated Two-Fold Interpenetrating Metal-Organic Frameworks for the Detection, Discrimination, and Degradation of Phenolic Pollutants

Phenols are widely used for commercial production, while they pose a hazard to the environment and human health. Thus, investigation of convenient and efficient methods for the detection, discrimination, and degradation of phenols becomes particularly important. Herein, two new polyoxometalate (POM)-based compounds, [Co₂(btap)₄(H₂O)₄][SiW₁₂O₄₀] (Co-POM) and [Ni₂(btap)₄(H₂O)₄][SiW₁₂O₄₀] (Ni-POM) (btap = 3,5-bis(triazol-1-yl)pyridine), are prepared via a hydrothermal synthesis method. The compounds show a fascinating structural feature of a POM-encapsulated twofold interpenetrating dia metal-organic framework. More importantly, besides the novel structures, the compound Co-POM realizes three functions, namely, the simultaneous detection, discrimination, and degradation of phenols. Specifically, Co-POM shows an excellent colorimetric detection performance toward phenol with a detection limit (LOD) ca. 1.32 μM, which is lower than most reported colorimetric detectors for phenol. Also, a new colorimetric sensor system based on Co-POM can discriminate phenol, 4-chlorophenol, and o-cresol with ease. Further, Co-POM exhibits a photocatalytic degradation property for 4-chlorophenol under irradiation of visible light with the highest degradation rate at 62% after irradiation for 5 h. Therefore, this work provides the first example of a POMs-based multifunctional material for achieving the detection, discrimination, and degradation of phenolic pollutants.

Electrical bistability based on metal-organic frameworks

Electrical bistability existing in biochemical networks is critical for the proper functionalization of living systems. The development of artificial materials with electrical bistability begun to attract much interest due to their broad application prospects, especially in the field of memristors. Metal-organic frameworks (MOFs) have advantages in regular pores, crystallinity, structural designability and easy functionalization, which can promote the construction of novel MOF-based memristors and facilitate a better understanding of switching mechanisms. Here, we highlight recent advances in electrically bistable MOFs as memristors, and discuss their switching mechanisms, including interfacial reaction, proton-transfer mechanism, metal ion migration, charge trapping/detrapping and other mechanisms. Challenges and future perspectives are also presented.

POMCPs with Novel Two Water-Assisted Proton Channels Accommodated by MXenes for Asymmetric Supercapacitors

To develop high-performance supercapacitors, the negative electrode is at present viewed as one of the most challenging tasks for obtaining the next-generation of energy storage devices. Therefore, in this study, a polyoxometalate-based coordination polymer [Zn(itmb)₃ H₂ O][H₂ SiW₁₂ O₄₀ ]·5H₂ O (1) is designed and prepared by a simple hydrothermal method for constructing a high-capacity negative electrode. Polymer 1 has two water-assisted proton channels, which are conducive to enhancing the electrical conductivity and storage capacity. Then, MXene Ti₃ C₂ T_x is chosen to accommodate coordination polymer 1 as the interlayer spacers to improve the conductivity and cycling stability of 1, while preventing the restacking of MXene. Expectedly, the produced composite electrode 1@Ti₃ C₂ T_x shows an excellent specific capacitance (1480.1 F g^-1 at 5 A g^-1 ) and high rate performance (a capacity retention of 71.5% from 5 to 20 A g^-1 ). Consequently, an asymmetric supercapacitor device is fabricated using 1@Ti₃ C₂ T_x as the negative electrode and celtuce leaves-derived carbon paper as the positive electrode, which demonstrates ultrahigh energy density of 32.2 Wh kg^-1 , and power density 2397.5 W kg^-1 , respectively. In addition, the ability to illuminate a red light-emitting diode for several minutes validates its feasibility for practical application.

Cobalt complexes tuned by Anderson-type polyoxometalates and bis-amide derivative ligands featuring a 'V'-like connector for efficient ampere sensing and the visible-light catalytic reduction of Cr(VI)

To exploit polyoxometalate (POM)-based metal-organic complexes (MOCs) with outstanding electro- and photo-chemical performances, two new bis-amide derivative N-donor ligands featuring a 'V'-like connector, 4,4'-bis(3-pyridinecarboxamide)phenylmethane (L¹) and 4,4'-bis(3-pyridinecarboxamide)phenylketone (L²), were designed and reacted with Anderson-type POMs in the presence of Co(II) ions under solvothermal conditions, which generated four MOCs: [Co₂(L¹)₂(AlMo₆H₅O₂₄)]·4H₂O (1), [Co₂(HL¹)₂(H₂O)₆(TeMo₆O₂₄)]·2H₂O (2), [Co₂(HL²)₂(H₂O)₄[AlMo₆H₆O₂₄]₂]·5H₂O (3), and [Co₂(HL²)₂(H₂O)₆(TeMo₆O₂₄)]·2H₂O (4). All the complexes showed supramolecular structures via hydrogen bond interaction, which resulted from the 2D layers for 1, the satellite-like structural units for 2 and 4, but the 1D chains for 3. In these structures, the POMs and organic ligands exhibited different coordination modes. Both 2 and 4 showed efficient ampere sensing activities for Cr(VI) with lower limits of detection of 0.029 and 0.038 μM, respectively. Complexes 1 and 2 showed good visible-light catalytic behavior toward the reduction of Cr(VI), which offers more chances for developing electrochemical sensors and photocatalysts for Cr(VI).

Electrocatalytic reduction of 4-nitrophenol over Ni-MOF/NF: understanding the self-enrichment effect of H-bonds

The chemical adsorption and active sites play a key role in electrocatalysis, so Ni-MOF/nickel foam was fabricated for efficiently reducing 4-nitrophenol (4-NP) without any sacrificial agents. The coordinated water molecules induced the formation of hydrogen bonds (H-bonds) with the nitro group, contributing to the self-enrichment of 4-NP. The reaction rate reached 0.351 μmol min^-1 mg^-1. Therefore, this work provides a new insight into the H-bond effect in the field of electrocatalysis.

Insights into organic-inorganic hybrid molecular materials: organoimido functionalized polyoxomolybdates

Polyoxometalates (POMs) are polyatomic anions that comprise transition metal group 5 (V, Nb, Ta) or group 6 (Mo, W) oxyanions connected together by shared oxygen atoms. POMs are fascinating because of their exclusive and remarkable characteristics. One of the most interesting features of POMs is their capability to function as an electron relay by performing stepwise multi-electron redox reactions while maintaining their structural integrity. Functionalization of POMs with amino organic compounds results in organoimido derivatives of polyoxometalates, which have aroused interest due to augmentation of their properties. Comprehensive study has shown that the synthesis methodologies to obtain desired organoimido derivatives of POMs by employing various imido-releasing reagents have progressed drastically in recent decades, particularly the innovative DCC-dehydrating technique. These organoimido functionalized POMs have been used as major building blocks to develop unique nanostructured organic-inorganic hybrid molecular materials. Many conventional organic synthesis processes such as Pd-catalyzed carbon-carbon coupling and esterification reactions have been performed with organoimido functionalized POMs where the presence of POM triggered the reaction process. Thus, investigation of the reactivity of organoimido derivatives of POMs foreshadows the intriguing future of POMs chemistry.

Assembly of a coordination polymer with sulphate-capped pentamolybdate units and copper: Synthesis, Structure, Magnetic and Catalytic studies

A new coordination polymer based upon the sulphate-capped pentamolybdate unit has been synthesized from the reaction of {Mo3S7Br6}2- with copper(II) bromide and pyridine, in DMF. The as-synthesized compound, formulated as...

Block copolymer-assisted synthesis of VO2 (B) microflowers for supercapacitor applications

Nanoporous metal oxides are appealing candidates for energy storage applications as they can interact with guest species from inner and outer surfaces, leading to improved energy and power density performance. We have synthesized VO₂ (B) microflowers with a stable phase and tailored porous structures utilizing block copolymers to achieve excellent supercapacitor performance.

pH-Controlled assembly of [ZnW12O40]6--based hybrids from a 0D dimer to a 2D network: synthesis, crystal structure, and photocatalytic performance in transformation of toluene into benzaldehyde

Polyoxometalate-based organic-inorganic hybrids have attracted considerable attention due to their fascinating structures and wide application prospects. In this work, using the same building blocks, ligands and metal ions (ZnW₁₂O₄₀^6-(ZnW₁₂), 2,2'-bipyridine (2,2'-bipy), and Cu²⁺), we synthesized three new POM-based hybrids by controlling the pH values of the reaction systems. These three compounds {(Zn_0.6(H₂)_0.4W₁₂O₄₀)[Cu(2,2'-bipy)(H₂O)][Cu(2,2'-bipy)(H₂O)₂][Cu(2,2'-bipy)(H₂O)₃]}₂·6H₂O (1), (Me₄N)₂{ZnW₁₂O₄₀[Cu(2,2'-bipy)(H₂O)][Cu(2,2'-bipy)(H₂O)₃]}·5H₂O (2), and {(Zn_0.5(H₂)_0.5W₁₂O₄₀)[Cu(2,2'-bipy)][Cu(2,2'-bipy)(H₂O)][Cu(2,2'-bipy)(H₂O)₂]}·5H₂O (3) have been structurally characterized by single-crystal X-ray diffraction. Compound 1 appears as a dimeric cluster structure, while compounds 2 and 3 appear as a 1D chain structure and a 2D network, respectively. The semiconducting properties of compounds 1-3 are different, which was demonstrated by band gap (E_g) and photocurrent response measurements. Compound 3 can efficiently catalyze the photooxidation of toluene to benzaldehyde with high selectivity using molecular oxygen as the oxidant component. Moreover, compound 3 was recycled and reused three times without significant degradation in conversion and selectivity. In addition, the mechanism of the photocatalytic reaction was also investigated.

Gas-solid phase flow synthesis of Cu-Co-1,3,5-benzenetricarboxylate for electrocatalytic oxygen evolution

Using an environmentally friendly method to produce a stable and highly catalytically active electrocatalyst for the oxygen evolution reaction (OER) is becoming increasingly urgent. Herein, a novel bimetallic metal-organic framework (MOF), specifically a copper-cobalt 1, 3, 5-benzenetricarboxylate (Cu-Co-BTC) MOF, was successfully prepared by employing the gas-solid two-phase flow (GSF) synthetic technique. The as-prepared Cu-Co-BTC with its multiple active sites afforded a current density of 10 mA cm^-2 at 239 mV for the OER in a 1 mol L^-1 KOH solution, and showed a better electrocatalytic performance than did single-metal-containing Cu-BTC and Co-BTC materials. This work provides a new idea, one involving using novel gas-solid phase reactions for the preparation of electrocatalysts in large quantities.

{BW12O40} Hybrids Modified by in Situ Synthesized Rigid Ligand with Supercapacitance and Photocatalytic Properties

Organic rigid ligand-modified polyoxometalate-based materials possess complex and diverse structures, promising electrochemical energy storage properties and outstanding photocatalytic capabilities. Hence, two new [BW₁₂O₄₀]^5-(abbreviated as {BW₁₂O₄₀})-based inorganic-organic hybrids [{Cu(en)₂(H₂O)}][{Cu(pdc)(en)}{Cu(en)₂}(BW₁₂O₄₀)]·2H₂O (1) and [{Cu^I₅(pz)₆(H₂O)₄}(BW₁₂O₄₀)] (2) (pdc = 2-picolinate, en = ethylenediamine, pz = pyrazine) were successfully synthesized through a hydrothermal method. Among them, pdc and pz were obtained by in situ transformation from 2,6-pyridinedicarboxylic acid (H₂ pydc) and 2,3-pyrazinedicarboxylic acid (H₂pzdc), respectively. In compound 1, the {BW₁₂O₄₀} clusters as an intermediate junction connect with {Cu(pdc)(en)}{Cu(en)₂} and {Cu(en)₂(H₂O)} to form monomers, which in turn form supramolecular chains, sheets, and space network via hydrogen bonding. The {BW₁₂O₄₀} clusters are packed into copper-pyrazine frameworks in compound 2, and a unique polyoxometalate-based metal organic frameworks (POMOFs) structure with a new topology of {12}₂{6.12³.14²}₂{6².12.14².18}{6².12³.16}{6}₆ is formed via covalent bonds. When used as electrode materials for supercapacitors, the values of specific capacitance are 651.56 F g^-1 for 1-GCE and 584.43 F g^-1 for 2-GCE at a current density of 2.16 A g^-1 and good cycling stability (90.94%, 94.81% of the initial capacity after 5000 cycles at 15.12 A g^-1, respectively). The kinetic analysis reveals that surface capacitance plays a major role. Furthermore, both compounds can effectively degrade Rhodamine B (RhB) and Methylene blue (MB), showing the outstanding photocatalytic performance.

Imidazole substituted Zinc(II) phthalocyanines for co-catalyst-free photoelectrochemical and photocatalytic hydrogen evolution: influence of the anchoring group

Novel zinc phthalocyanine derivatives, ZnPc-1 and ZnPc-2, consisting of one and four imidazole units, respectively, have been synthesized and utilized as panchromatic photosensitizers for photocatalytic and photoelectrochemical H₂ evolution. The effect of the imidazole-anchoring group on the photocatalytic H₂ production has been compared with ZnPc-3, which possesses a carboxylic acid unit as the anchoring group. ZnPc-1/TiO₂ shows the best photoactivity with the highest H₂ evolution rate of 0.4006 mmol g^-1 h^-1, which is much higher than that of ZnPc-2/TiO₂ and ZnPc-3/TiO₂ (0.3319 mmol g^-1 h^-1 and 0.3555 mmol g^-1 h^-1, respectively). After 20 h of irradiation, ZnPc-1 produces an H₂ production rate of 3.4187 mmol g^-1 with a turnover number (TON) of 14863 and a solar-to-hydrogen energy (STH) conversion efficiency of 1.03%, without using a co-catalyst.

Two new polyoxometalate-based metal-organic complexes for the detection of trace Cr(VI) and their capacitor performance

Two new Keggin-type polyoxometalate (POM)-based metal-organic complexes (MOCs) H3[Cu2(4-dpye)2(PMo12O40)] (1) and H[Cu2(4-Hdpye)2(PMo12O40)(H2O)4]·2H2O (2) were constructed with a new N,N'-bis (4-pyrimidinecarboxamido)-1,2-ethane (4-H2dpye) ligand by the hydrothermal/solvothermal method. Complex 1 was a 2D layered structure constructed from 1D metal-organic chains [Cu(4-dpye)]n and Keggin-type [PMo12O40]3- polyoxoanions. Complex 2 displays a 3D supramolecular framework formed by discrete [PMo12O40]3- polyoxoanions and binuclear metal-organic loops [Cu2(4-Hdpye)2]. The electrocatalytic behaviors of carbon paste electrodes modified by complexes 1 and 2 (1-CPE and 2-CPE) were investigated. The 1-CPE and 2-CPE were used as electrochemical sensors to detect trace Cr(vi), and the low limits of detection (LOD) are 1.27 × 10-7 M for 1 and 1.71 × 10-7 M for 2, which are lower than the maximum allowable concentration of Cr(vi) in drinking water specified by the World Health Organization (WHO). In addition, the performances of complexes 1 and 2 modified carbon cloth electrodes (1-CC and 2-CC) as supercapacitor materials have also been studied. The influence of the structure on electrocatalytic and capacitor performances is discussed.

Unprecedented monofunctionalized β-Anderson clusters: [R1R2C(CH2O)2MnIVW6O22]6-, a class of potential candidates for new inorganic linkers

Novel Anderson-type polyoxomanganotungstate clusters with the β-isomer structure, [{R₁R₂C(CH₂O)₂}Mn^IVW₆O₂₂]^6-, were synthesized and monofunctionalized with derivatives of 1,3-propanediol via a one-pot strategy, and show unprecedented coordination activity as non-lacunary polyoxotungstate clusters and could have potential in the future construction of POM-frameworks.

Controllable synthesis of two adenosine 5'-monophosphate nucleotide coordination polymers via pH regulation: crystal structure and chirality

Two types of Cu(ii)-AMP-4,4'-bipy coordination polymers, {[Cu(AMP)(4,4'-bipy)(H₂O)₃]·5H₂O}n (1) and {[Cu₂(HAMP)₂(4,4'-bipy)₂(H₂O)₄]·2NO₃·11H₂O}n (2) (Na₂AMP = adenosine 5'-monophosphate disodium salt), were synthesised through pH control. X-ray single-crystal diffraction analysis revealed that 1 and 2 are one-dimensional (1D) coordinating coordination polymers. The nucleotide in 1 was not protonated whereas that in 2 was protonated. With the protonated NO₃^- in 2 entering the crystal lattice, it plays a role in balancing the charge. The chirality was studied using solid-state circular dichroism (CD) spectroscopy based on the analysis of crystal structures.