Tip-Enhanced Infrared Imaging with Sub-10 nm Resolution and Hypersensitivity

Surface-phonon-polariton-enhanced photoinduced dipole force for nanoscale infrared imaging

The photoinduced dipole force (PiDF) is an attractive force arising from the Coulombic interaction between the light-induced dipoles on the illuminated tip and the sample. It shows extreme sample-tip distance and refractive index dependence, which is promising for nanoscale infrared (IR) imaging of ultrathin samples. However, the existence of PiDF in the mid-IR region has not been experimentally demonstrated due to the coexistence of photoinduced thermal force (PiTF), typically one to two orders of magnitude higher than PiDF. In this study, we demonstrate that, with the assistance of surface phonon polaritons, the PiDF of c-quartz can be enhanced to surpass its PiTF, enabling a clear observation of PiDF spectra reflecting the properties of the real part of permittivity. Leveraging the detection of the PiDF of phonon polaritonic substrate, we propose a strategy to enhance the sensitivity and contrast of photoinduced force responses in transmission images, facilitating the precise differentiation of the heterogeneous distribution of ultrathin samples.

From Unregulated Networks to Designed Microstructures: Introducing Heterogeneity at Different Length Scales in Photopolymers for Additive Manufacturing

Photopolymers have been optimized as protective and decorative coating materials for decades. However, with the rise of additive manufacturing technologies, vat photopolymerization has unlocked the use of photopolymers for three-dimensional objects with new material requirements. Thus, the originally highly cross-linked, amorphous architecture of photopolymers cannot match the expectations for modern materials anymore, revealing the largely unanswered question of how diverse properties can be achieved in photopolymers. Herein, we review how microstructural features in soft matter materials should be designed and implemented to obtain high performance materials. We then translate these findings into chemical design suggestions for enhanced printable photopolymers. Based on this analysis, we have found microstructural heterogenization to be the most powerful tool to tune photopolymer performance. By combining the chemical toolbox for photopolymerization and the analytical toolbox for microstructural characterization, we examine current strategies for physical heterogenization (fillers, inkjet printing) and chemical heterogenization (semicrystalline polymers, block copolymers, interpenetrating networks, photopolymerization induced phase separation) of photopolymers and put them into a material scientific context to develop a roadmap for improving and diversifying photopolymers' performance.

Nanoscale chemical characterization of secondary protein structure of F-Actin using mid-infrared photoinduced force microscopy (PiF-IR)

The recently developed photoinduced force microscopy for mid-infrared (PiF-IR) offers high spectral resolution in combination with surface sensitivity and a spatial resolution in the range of a few nanometers. Although PiF-IR has primarily been applied to polymer materials, this technology presents significant potential for the chemical characterization of cellular structures approaching single-molecule sensitivity. We applied PiF-IR to differently polymerized F-Actin samples finding general agreement with FTIR spectra from the same samples. Single PiF-IR spectra of F-Actin show variations in the amide I band spectral region, which is related to secondary protein structure. Local variations are also seen in PiF-IR hyperspectra in this region. Such high sensitivity is a necessary requirement for discriminating Actin organization into bundles and other networks in cells and tissue. We applied PiF-IR to mouse liver tissue ex vivo. Single-frequency PiF-IR scans at three different IR frequencies show significant variations in local contrast. However, the presence of other proteins and the unique spatial resolution of PiF-IR pose a challenge to interpreting and validating such data. Careful design of model systems and further theoretical understanding of PiF-IR data far from bulk averages are needed to fully unfold the potential of PiF-IR for high-resolution chemical investigation in the Life Sciences.

Atomic Force Microscopy-Based Nanoscale Infrared Techniques for Catalysis

Atomic force microscopy (AFM)-based nanoscale infrared (nano-IR) techniques have found extensive application in the fields of chemistry, physics, and materials science, enabling the visualization of nanoscale features that surpass the optical diffraction limit. More recently, tentative investigations have been conducted into the use of these techniques in the field of catalysis, particularly in studying interfacial processes involving molecular monolayer samples. IR nanoimaging and nanospectroscopy offer unique perspectives on catalytic processes. Considering the specific characteristics of catalytic processes, this Perspective highlights the need for and reviews the current status of AFM-based nano-IR techniques for catalysis investigations, which aims to contribute to a deeper understanding of the nanoscale mechanisms underlying the catalytic processes.

Mechanistic Insights Gained by High Spatial Resolution Reactivity Mapping of Homogeneous and Heterogeneous (Electro)Catalysts

The recent development of high spatial resolution microscopy and spectroscopy tools enabled reactivity analysis of homogeneous and heterogeneous (electro)catalysts at previously unattainable resolution and sensitivity. These techniques revealed that catalytic entities are more heterogeneous than expected and local variations in reaction mechanism due to divergences in the nature of active sites, such as their atomic properties, distribution, and accessibility, occur both in homogeneous and heterogeneous (electro)catalysts. In this review, we highlight recent insights in catalysis research that were attained by conducting high spatial resolution studies. The discussed case studies range from reactivity detection of single particles or single molecular catalysts, inter- and intraparticle communication analysis, and probing the influence of catalysts distribution and accessibility on the resulting reactivity. It is demonstrated that multiparticle and multisite reactivity analyses provide unique knowledge about reaction mechanism that could not have been attained by conducting ensemble-based, averaging, spectroscopy measurements. It is highlighted that the integration of spectroscopy and microscopy measurements under realistic reaction conditions will be essential to bridge the gap between model-system studies and real-world high spatial resolution reactivity analysis.

Development of low-temperature and ultrahigh-vacuum photoinduced force microscopy

In this paper, we develop optical and electronic systems for photoinduced force microscopy (PiFM) that can measure photoinduced forces under low temperature and ultrahigh vacuum (LT-UHV) without artifacts. For our LT-UHV PiFM, light is irradiated from the side on the tip-sample junction, which can be adjusted through the combination of an objective lens inside the vacuum chamber and a 90° mirror outside the vacuum chamber. We measured photoinduced forces due to the electric field enhancement between the tip and the Ag surface, and confirmed that photoinduced force mapping and measurement of photoinduced force curves were possible using the PiFM that we developed. The Ag surface was used to measure the photoinduced force with high sensitivity, and it is effective in enhancing the electric field using the plasmon gap mode between the metal tip and the metal surface. Additionally, we confirmed the necessity of Kelvin feedback during the measurement of photoinduced forces, to avoid artifacts due to electrostatic forces, by measuring photoinduced forces on organic thin films. The PiFM, operating under low temperature and ultrahigh vacuum developed here, is a promising tool to investigate the optical properties of various materials with very high spatial resolution.

Super-resolution mid-infrared spectro-microscopy of biological applications through tapping mode and peak force tapping mode atomic force microscope

Small biomolecules at the subcellular level are building blocks for the manifestation of complex biological activities. However, non-intrusive in situ investigation of biological systems has been long daunted by the low spatial resolution and poor sensitivity of conventional light microscopies. Traditional infrared (IR) spectro-microscopy can enable label-free visualization of chemical bonds without extrinsic labeling but is still bound by Abbe's diffraction limit. This review article introduces a way to bypass the optical diffraction limit and improve the sensitivity for mid-IR methods - using tip-enhanced light nearfield in atomic force microscopy (AFM) operated in tapping and peak force tapping modes. Working principles of well-established scattering-type scanning near-field optical microscopy (s-SNOM) and two relatively new techniques, namely, photo-induced force microscopy (PiFM) and peak force infrared (PFIR) microscopy, will be briefly presented. With ∼ 10-20 nm spatial resolution and monolayer sensitivity, their recent applications in revealing nanoscale chemical heterogeneities in a wide range of biological systems, including biomolecules, cells, tissues, and biomaterials, will be reviewed and discussed. We also envision several future improvements of AFM-based tapping and peak force tapping mode nano-IR methods that permit them to better serve as a versatile platform for uncovering biological mechanisms at the fundamental level.

Correlating the Morphological Evolution of Individual Catalyst Particles to the Kinetic Behavior of Metallocene-Based Ethylene Polymerization Catalysts

Kinetics-based differences in the early stage fragmentation of two structurally analogous silica-supported hafnocene- and zirconocene-based catalysts were observed during gas-phase ethylene polymerization at low pressures. A combination of focused ion beam-scanning electron microscopy (FIB-SEM) and nanoscale infrared photoinduced force microscopy (IR PiFM) revealed notable differences in the distribution of the support, polymer, and composite phases between the two catalyst materials. By means of time-resolved probe molecule infrared spectroscopy, correlations between this divergence in morphology and the kinetic behavior of the catalysts' active sites were established. The rate of polymer formation, a property that is inherently related to a catalyst's kinetics and the applied reaction conditions, ultimately governs mass transfer and thus the degree of homogeneity achieved during support fragmentation. In the absence of strong mass transfer limitations, a layer-by-layer mechanism dominates at the level of the individual catalyst support domains under the given experimental conditions.

Embedding an Amphiphilic 4-Hydroxy Thiazole Dye in Langmuir Matrices: Studying Miscibilities with Arylic and Alkylic Matrix Amphiphiles via Langmuir Isotherms and Photo-induced Force Microscopy

We present here a fundamental study on the miscibility between a prototype amphiphilic dye and alkylic and arylic Langmuir monolayers. Embedding dyes in such matrices is crucial for utilizing dyes in any photo-energy conversion process if the involved dyes form aggregates that provide thermal deactivation channels. Because miscibility in Langmuir matrices depends on the blending ratio between the dye and matrix and on the Langmuir film density, as characterized via the surface pressure and the mean molecular area, we employ Langmuir miscibility studies to identify ideal miscibility parameters for each matrix. Atomic force microscopy (AFM) results support miscibility between the dye and both matrix materials at low surface pressures, where smooth and homogeneous films are obtained. AFM and photo-induced force microscopy (PiFM) reveal phase separation if the Langmuir monolayers are deposited at surface pressures above 8 mN/m at which reorientation of the chromophores has been reported. The nanoscale chemical fingerprint mapping enabled by PiFM enables assigning segregated spots to small stearic acid (SA)-enriched domains that have not been detected via AFM, thus demonstrating the value of the IR-spectroscopic contrast provided by PiFM. In this work, we have presented a so far unexploited matrix material (terphenylene carboxylic acid; TPCA) and found it equally suitable for embedding dyes as the standard amphiphile SA. In contrast to SA, TPCA is composed of rigid and electrically conducting π-electron systems, hence, being predestined for aligning dyes in Langmuir matrices and for application in optoelectronic systems.

Integrated Tapping Mode Kelvin Probe Force Microscopy with Photoinduced Force Microscopy for Correlative Chemical and Surface Potential Mapping

Kelvin probe force microscopy (KPFM) is a popular technique for mapping the surface potential at the nanoscale through measurement of the Coulombic force between an atomic force microscopy (AFM) tip and sample. The lateral resolution of conventional KPFM variants is limited to between ≈35 and 100 nm in ambient conditions due to the long-range nature of the Coulombic force. In this article, a novel way of generating the Coulombic force in tapping mode KPFM without the need for an external AC driving voltage is presented. A field-effect transistor (FET) is used to directly switch the electrical connectivity of the tip and sample on and off periodically. The resulting Coulomb force induced by Fermi level alignment of the tip and sample results in a detectable change of the cantilever oscillation at the FET-switching frequency. The resulting FET-switched KPFM delivers a spatial resolution of ≈25 nm and inherits the high operational speed of the AFM tapping mode. Moreover, the FET-switched KPFM is integrated with photoinduced force microscopy (PiFM), enabling simultaneous acquisitions of high spatial resolution chemical distributions and surface potential maps. The integrated FET-switched KPFM with PiFM is expected to facilitate characterizations of nanoscale electrical properties of photoactive materials, semiconductors, and ferroelectric materials.

In situ Nanoscale Infrared Spectroscopy of Water Adsorption on Nanoislands of Surface-Anchored Metal-Organic Frameworks

Despite technological advancements, probing gas‐solid interfaces at the nanoscale is still a formidable challenge. New nano‐spectroscopic methods are needed to understand the guest–host interactions of functional materials during gas sorption, separation, and conversion. Herein, we introduce in situ Photoinduced Force Microscopy (PiFM) to evidence site‐specific interaction between Metal‐Organic Frameworks (MOFs) and water. To this end, we developed amphiphilic Surface‐anchored MOF (SURMOF) model systems using self‐assembly for the side‐by‐side hetero‐growth of nanodomains of hydrophilic HKUST‐1 and hydrophobic ZIF‐8. PiFM was used to probe local uptake kinetics and to show D₂O sorption isotherms on (defective) HKUST‐1 paddlewheels. By monitoring defect vibrations, we visualized in real‐time the saturation of existing defects and the creation of D₂O‐induced defects. This work shows the potential of in situ PiFM to unravel gas sorption mechanisms and map active sites on functional (MOF) materials.

d-sp Interband Transition Excited Carriers Promoting the Photochemical Growth of Plasmonic Gold Nanoparticles

As an important damping way of the light absorption of plasmonic nanoparticles, the d-sp interband transition within the short wavelength regime has been recently drawing attentions in photochemistry. Compared with the intraband Landau damping, the d-sp interband transition excited carriers have larger populations and longer relaxation times, which is promising to match the photochemical reactions in time scale. Here, we propose a novel approach to the growth of plasmonic gold nanoparticles more efficiently promoted by d-sp interband transition excited charge carriers than by plasmon excited carriers. It is founded that photochemical growth of plasmonic gold nanoparticles can be modulated by engineering the electrochemical potential of precursor using different surfactants. From the distribution of surfactant on a single gold nanoparticle revealed by nanoscale resolved IR mapping, a reasonable photochemical reaction mechanism mediated by d-sp interband excitation is suggested. The results highlight the importance of d-sp interband transition excited carriers in photochemical reactions especially for materials science.

Direct Chemical Imaging of Ligand-Functionalized Single Nanoparticles by Photoinduced Force Microscopy

Chemical characterizations of biochemically functionalized single nanoparticles are necessary to optimize the nanoparticle surface functionality in recently advanced nanobiological applications but have not yet been fully explored because of technical difficulties. Exploiting the photoinduced force exerted on a light-illuminated nanoscale tip, nanoscale mid-infrared hyperspectral images with a 10 nm spatial resolution of a monolayer ligand-functionalized single gold nanoparticle under ambient and environmental conditions are presented. We extend our study to the diagnosis of nanoscale heterogeneous chemical contaminants which come from a particle functionalization process but are undetectable in conventional ensemble-averaged imaging technique. High sensitivity and high spatial resolution are achieved via the strongly localized tip-enhanced force at the junction between the gold-coated tip and the functionalized nanoparticle in photoinduced force microscopy, which far exceeds the capability of the conventional methods. The present study paves a new way to directly detect heterogeneous nanochemicals at the single-component level, which is necessary to evaluate nanomaterial safety in biomedical applications.