Highly Fluorescent dye-nanoclay Hybrid Materials Made from Different Dye Classes

Natural Degradation Behavior of Poly(lactic acid) Nanocomposite Films and the Adsorption Behavior of Degraded Products on Cu(II)

In this study, the degradation behavior of poly(lactic acid) nanocomposite films (PLA/Hec-g@PS) under extreme natural environments was investigated, and the degraded PLA based films were applied to adsorb Cu(II). During the early and midstages of degradation, the surface roughness and crack propagation rate of PLA/Hec-g@PS films were significantly lower than those of PLA films. This could be due to the fact that Hec-g@PS enhanced the interaction forces between C-O-C + CH3 and C═O in the PLA chains, thereby mitigating the degradation of PLA. Neural network predictions indicated that the molecular weight of PLA films decreased to 30% after 1344 days, whereas PLA/Hec-g@PS films reached the same reduction in 1451 days, extending the lifespan of PLA by 1.08 times. The environmental impact of PLA/Hec-g@PS was further assessed by their adsorption behavior toward Cu(II). It was found that PLA films adsorbed 244.51 μg/g of Cu(II), while PLA/Hec-g@PS films adsorbed 372.63 μg/g of Cu(II). The isotherm adsorption model showed that the maximum adsorption capacities (qm) of PLA and PLA/Hec-g@PS were 326.60 μg/g and 441.51 μg/g, respectively. This improvement offers PLA based films new possibilities for applications in wastewater treatment and soil remediation.

Fluorescence enhancement of benzimidazolium derivative on clay nanosheets by surface-fixation induced emission (S-FIE)

The photophysical behaviors of benzimidazolium derivative [4-(1,3-dimethylbenzimidazol-3-imu-2-yl)-N, N-diphenylaniline (2-(4-(diphenylamino)phenyl)-1,3-dimethyl-1H-benzo[d]imidazol-3-ium)] (BID) in water, organic solvents and on synthetic saponite were investigated. The fluorescence quantum yield (Φf) of BID was 0.91 on the saponite surface under the optimal condition, while that in water was 0.010. Such fluorescence enhancement on the inorganic surface is called "surface-fixation induced emission (S-FIE)". This fluorescence enhancement ratio for BID is significantly high compared to that of conventional S-FIE active dyes. From the values of Φf and the excited lifetime, the non-radiative deactivation rate constant (knr) and radiative deactivation rate constant (kf) of BID on the saponite surface and in water were determined. Results showed that the factors for fluorescence enhancement were both the increase of kf and the decrease of knr on the saponite surface; especially, knr decreased by more than two orders due to the effect of nanosheets.

Addition of Laponite to gelatin methacryloyl bioinks improves the rheological properties and printability to create mechanically tailorable cell culture matrices

Extrusion-based bioprinting has gained widespread popularity in biofabrication due to its ability to assemble cells and biomaterials in precise patterns and form tissue-like constructs. To achieve this, bioinks must have rheological properties suitable for printing while maintaining cytocompatibility. However, many commonly used biomaterials do not meet the rheological requirements and therefore require modification for bioprinting applications. This study demonstrates the incorporation of Laponite-RD (LPN) into gelatin methacryloyl (GelMA) to produce highly customizable bioinks with desired rheological and mechanical properties for extrusion-based bioprinting. Bioink formulations were based on GelMA (5%-15% w/v) and LPN (0%-4% w/v), and a comprehensive rheological design was applied to evaluate key rheological properties necessary for extrusion-based bioprinting. The results showed that GelMA bioinks with LPN (1%-4% w/v) exhibited pronounced shear thinning and viscoelastic behavior, as well as improved thermal stability. Furthermore, a concentration window of 1%-2% (w/v) LPN to 5%-15% GelMA demonstrated enhanced rheological properties and printability required for extrusion-based bioprinting. Construct mechanical properties were highly tunable by varying polymer concentration and photocrosslinking parameters, with Young's moduli ranging from ∼0.2 to 75 kPa. Interestingly, at higher Laponite concentrations, GelMA cross-linking was inhibited, resulting in softer hydrogels. High viability of MCF-7 breast cancer cells was maintained in both free-swelling droplets and printed hydrogels, and metabolically active spheroids formed over 7 days of culture in all conditions. In summary, the addition of 1%-2% (w/v) LPN to gelatin-based bioinks significantly enhanced rheological properties and retained cell viability and proliferation, suggesting its suitability for extrusion-based bioprinting.

Layered silicate edge-linked perylene diimides: Synthesis, self-assembly and energy transfer

The control over intermolecular interactions between chromophores at nanomaterial interfaces is important for sensing and light-harvesting applications. To that aim, inorganic nanoparticles with anisotropic shape and surface chemistry can serve as useful supports for organic modification. Herein, novel asymmetric perylene diimides with aspartic acid and oleyl terminal groups were grafted to the edges of the layered silicate clay Laponite, a water-dispersible discoidal nanoparticle. The photophysical properties and solvent-dependent self-assembly of the nanoclay-grafted perylenes were investigated, revealing that the polarity of the terminating ligand dictates the aggregation behavior in aqueous solution, where increased water content generally led to the formation of perylene H-aggregates. The anionic basal surface of the nanoclay provided a binding site for a cationic fluorophore, leading to energy transfer from the face-bound donor to the edge-bound perylene acceptor. This study encourages further research on the use of functional ligands for the formation of organic-inorganic hybrids, particularly where inorganic template particles with specific surface chemistry can be exploited to study intermolecular interactions. Overall, these findings should advance further design and implementation of novel semiconducting ligands towards inorganic-organic hybrids, with potential applications in sensing and energy harvesting.

Utilizing optical spectroscopy and 2',7'-difluorofluorescein to characterize the early stages of cement hydration

The increasingly sophisticated nature of modern, more environmentally friendly cementitious binders requires a better understanding and control particularly of the complex, dynamic processes involved in the early phase of cement hydration. In-situ monitoring of properties of a constantly changing system over a defined period of time calls for simple, sensitive, fast, and preferably also non-invasive methods like optical spectroscopy. Here, we exploit the time-dependent changes in the absorbance and fluorescence features of the negatively charged optical probe 2',7'-difluorofluorescein (DFFL) for the study of the hydration processes in pastes of white cement (WC), cubic tricalcium aluminate (C₃A), and tricalcium silicate (C₃S), the main phases of cement, and in pastes of quartz (Q) over 24 h after addition of the dye solution. For comparison, also conventional techniques like isothermal heat flow calorimetry were applied. Based upon the time-dependent changes in the spectroscopic properties of DFFL, that seem to originate mainly from dye aggregation and dye-surface interactions and considerably vary between the different pastes, molecular pictures of the hydration processes in the cement pastes are derived. Our results clearly demonstrate the potential of optical spectroscopy, i.e., diffuse reflectance, steady state and time-resolved fluorometry in conjunction with suitable optical reporters, to probe specific hydration processes and to contribute to a better understanding of the early hydration processes of cement at the molecular scale.

Effects of the Surface Charge Density of Clay Minerals on Surface-Fixation Induced Emission of Acridinium Derivatives

Surface-fixation induced emission is a fluorescence enhancement phenomenon, which is expressed when dye molecules satisfy a specific adsorption condition on the anionic clay surface. The photophysical behaviors of two types of cationic acridinium derivatives [10-methylacridinium perchlorate (Acr+) and 10-methyl-9-phenylacridinium perchlorate (PhAcr+)] on the synthetic saponites with different anionic charge densities were investigated. Under the suitable conditions, the fluorescence quantum yield (Φf) of PhAcr+ was enhanced 22.3 times by the complex formation with saponite compared to that in water without saponite. As the inter-negative charge distance of saponite increased from 1.04 to 1.54 nm, the Φf of PhAcr+ increased 1.25 times. In addition, the increase in the negative charge distance caused the increase in the integral value of the extinction coefficient and the radiative deactivation rate constant (k f) and the decrease in the nonradiative deactivation rate constant. It should be noted that the 2.3 times increase in k f is the highest among the reported values for the effect of clay. From these results, it was concluded that the photophysical properties of dyes can be modulated by changing the charge density of clay minerals.

Sensitivity enhancement of DHR123 radio-fluorogenic nanoclay gel dosimeter by incorporating surfactants and halogenides

Dosimetry of spatial dose distribution of ionizing radiation in tissue equivalent materials is particularly important for cancer radiotherapy. Here, we describe a radio-fluorogenic gel-based dosimeter that has achieved 16 times higher sensitivity by incorporating surfactants and halogenides. The gel dosimeters were prepared from dihydrorhodamine 123 (DHR123) and small amounts of nano-sized clay and a radiosensitizer. By comprehensively changing the type of additives for the sensitizer (three surfactants: Triton X-100, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide, and three halogenides: trichloroacetic acid, tribromoacetic acid and 2,2,2-trichloroethanol), the increase in sensitivity can be explained by an increase in relative fluorescence quantum yield and an increase in radiation chemical yield. These highly sensitive gel dosimeters also show dose rate independent sensitivity under irradiation at 0.64 and 0.77 Gy min⁻¹ using a 6 MV X-ray therapeutic beam from the medical linac.

Dosimetry of spatial dose distribution of ionizing radiation in tissue equivalent materials using high sensitive radio-fluorogenic gel dosimeter using DHR123 with sensitizer. (Radiation therapy planning image courtesy of Varian Medical Systems, Inc. All rights reserved.)

Thermodynamic study of the adsorption of acridinium derivatives on the clay surface

In this study, the adsorption behavior of mono-cationic acridinium derivatives on a synthetic clay mineral (Sumecton SA) was investigated. The acridinium derivatives were adsorbed on the clay surface without aggregation, as found from the changes in the absorption spectra of the acridinium derivatives with SSA and without SSA represented by two-component equilibrium systems of adsorbed and non-adsorbed components. Following the Langmuir isotherm analysis, the adsorption equilibrium constants and maximum adsorption amounts were determined for acridinium derivatives, and the Gibbs free energy change (ΔG) was calculated to be in the range of −33.8 to 40.0 kJ mol⁻¹ from the adsorption equilibrium constants. These results indicated that the adsorption of acridinium derivatives on the clay surface was an exergonic reaction. Moreover, thermodynamic parameters such as enthalpy change (ΔH) and entropy change (ΔS) were obtained from the temperature effect experiments. For all acridinium derivatives, ΔH (from −7.82 to −26.0 kJ mol⁻¹) and ΔS (0.047–0.088 kJ mol⁻¹ K⁻¹) were found to be negative and positive, respectively. It was suggested that not only electrostatic interactions, but also van der Waals forces and hydrophobic interactions played an important role in the adsorption of cationic aromatic molecules on the clay surface. Because these thermodynamic parameters showed a strong correlation with the molecular cross-sectional area of acridinium derivatives, it was suggested that the contribution of hydrophobic interactions became smaller as the molecular cross-sectional area became larger.

Thermodynamic studies indicate that van der Waals and hydrophobic interactions contribute to the adsorption of mono-cationic acridinium derivatives on the clay surface.

Synthesis, Formulation, and Characterization of Doxorubicin-Loaded Laponite/Oligomeric Hyaluronic Acid-Aminophenylboronic Acid Nanohybrids and Cytological Evaluation against MCF-7 Breast Cancer Cells

As a synthetic clay material, laponite RDS (LR) was investigated as an effective drug carrier as a result of the special nanodisk structure together with the negative-charged surface to achieve enhanced cellular uptake and targeted delivery. In this research work, the synthesized oligomeric hyaluronic acid-aminophenylboronic acid (oHA-APBA) was entangled onto LR nanodisks to fabricate a valid targeted platform for breast cancer therapy. Briefly, through the formation of amide bonds, 3-APBA was connected to the chain of oHA with a substituted ratio of 4.0 ± 0.2% to synthesize oHA-APBA copolymer. Thereafter, doxorubicin (DOX) was inserted into the interlayer space of LR by the way of the ion exchange process, followed by an assembly with oHA-APBA as a targeted protection layer. The satisfactory drug encapsulation efficiency (> 80%) and narrow size distribution were achieved. The in vitro drug release study demonstrated the release of DOX from DOX@LR/oHA-APBA was sustained and acid dependent. In addition, after fitting the drug cumulative release of DOX@LR/oHA-APBA under different pH conditions with several kinetic models, it was identified that drug release from DOX@LR/oHA-APBA nanohybrids at pH 5.0 was mainly dependent on both diffusion and ion exchange effects. However, under the condition of pH 7.4, the drug was most efficiently released by diffusion effect. Importantly, DOX@LR/oHA-APBA showed remarkable cellular uptake and intracellular drug distribution in MCF-7 cells, which were consistent with inhibitory ability against MCF-7 cells. Hence, the high DOX loading capacity and enhanced cellular tracking can enlighten LR/oHA-APBA as an effective drug delivery carrier for breast cancer therapy.

Laponite®: A key nanoplatform for biomedical applications?

Laponite® is a synthetic smectite clay that already has many important technological applications, which go beyond the conventional uses of clays in pharmaceutics and cosmetics. In biomedical applications, particularly in nanomedicine, this material holds great potential. Laponite® is a 2-dimensional (2D) nanomaterial composed of disk-shaped nanoscale crystals that have a high aspect ratio. These disks can strongly interact with many types of chemical entities (from small molecules or ions, to natural or synthetic polymers, to different inorganic nanoparticles) and are also easily functionalized and readily degraded in the physiological environment giving rise to non-toxic and even bioactive products. This review will highlight the potential of Laponite® as a nanomaterial in the fields of drug delivery, bioimaging, tissue engineering and regenerative medicine. New concepts, as well as novel innovative materials that stand out from the usual ones due to the unique properties of Laponite®, will also be presented and discussed.

LAPONITE® nanoplatform functionalized with histidine modified oligomeric hyaluronic acid as an effective vehicle for the anticancer drug methotrexate

The synthetic clay material, LAPONITE® (LAP), having a nanodisk structure together with a negatively charged surface, has been used for effective drug encapsulation by virtue of its interlayer space. In this research effort, the LAP nanodisk was used for the first time to encapsulate the antifolic methotrexate (MTX); the MTX-loaded LAP nanodisks (LAP/MTX) demonstrated a high drug loading efficiency of 80.39%. An efficient and reliable tumor-targeting device that rests on the synthesized oligomeric hyaluronic acid-l-histidine (oHA-His) was then encapsulated in the MTX-loaded LAP disks (forming LAP/MTX/oHA-His nanohybrids). The drug released from the LAP/MTX/oHA-His nanohybrids was pH-dependent and matched the first-order kinetics that describes the diffusion mechanism. In vitro biological evaluation manifested that the MTX-loaded LAP nanocarriers, particularly the LAP/MTX/oHA-His nanohybrids that have targetability and lysosomal antineoplastic activity, can be effectively internalized by the MCF-7 cell line, and can exhibit a more prominent anticancer cytotoxicity than free MTX. In vivo studies with mice indicated that the LAP/MTX/oHA-His nanohybrids demonstrated much higher antitumor efficiency compared to the LAP/MTX nanohybrids and pure MTX. Taken together, the LAP/oHA-His, CD44 receptor targeting and pH-sensitive multifunctional nanohybrids conferred the MTX with excellent cytocompatibility, dispersion stability, sustained pH-responsive release properties, and improved anticancer activity, and may be further developed as a potential active nanoplatform for various anticancer drugs.

Monitoring of nanoclay-protein adsorption isotherms via fluorescence techniques

The investigation of nanoparticles and their interaction with bio-macromolecules have become an important issue; the widely discussed protein corona around nanoparticles and their biological fate in general have drawn particular attention. Here, we focus on nanoclay dispersions and the use of solvatochromic fluorescent dyes (Dansyl and Coumarin 153) for monitoring the interaction with two model proteins, bovine serum albumin and β-lactoglobulin. On one hand, these dyes are poorly emissive in water, but experience a boost in their fluorescence when adsorbed into the hydrophobic domains of proteins. On the other hand, (nano)clays and clay minerals have previously been investigated in terms of their individual protein adsorption isotherms and their usefulness for the solubilization of water-insoluble dyes into an aqueous environment. In the following, we have combined all three individual parts (nanoclay, fluorophore and protein) in dispersions in a wide range of concentration ratios to systematically study the various adsorption processes via fluorescence techniques. In order to clarify the extent of dye diffusion and adsorption-desorption equilibria in the investigations, nanoclay hybrids with an adsorbed dye (Coumarin 153) and a covalently conjugated dye (Dansyl) were compared. The results suggest that the fluorescence progression of protein titration curves correlate with the amount of protein adsorbed, matching their reported adsorption isotherms on hectorite clays. Furthermore, experimental data on the protein monolayer formation around the nanoclays could be extracted due to only minor alterations of the dispersions' optical quality and transparency. In this manner, a fluorescence-based monitor for the formation of the globular protein layer around the nanoclay was realized.

Peptizing Mechanism at the Molecular Level of Laponite Nanoclay Gels

In the presence of additives such as etidronic acid (1-hydroxyethane-1,1-diphosphonic acid, HEDP), a process of peptizing of Laponite clay gels takes place. The peptizing process at the molecular level was directly revealed by ³¹P and ¹H high-resolution magic-angle sample spinning (HRMAS) NMR spectroscopy. Two NMR spectral components were detected and assigned to free etidronic acid and bound to the Laponite disk edges. Furthermore, with increase of temperature the ratio of bound-to-free etidronic acid increases. This thermal activation process could be explained by the increase in electrical polarization of the hydroxyl group at the edges and by the exfoliation of the tactoids that leads to more access to the additive molecules to the electrical charges of platelet edges. ³¹P HRNMR spectroscopy on sodium fluorohectorite with an aspect ratio of ∼750 shows a reduction of the bound etidronic acid molecules. Transmission electron microscopy (TEM), field-emission scanning microscopy (FESEM), UV-vis spectrophotometry, dynamic light scattering (DLS), and zeta potential results support the proposed peptizing mechanisms.