1
|
Yang S, Chen R, Zhang P, Yuan M, Li H, Jiang D. Fabrication and characterization of poly(lactic acid-trimethylene carbonate) based biodegradable composite films. Int J Biol Macromol 2024; 262:130148. [PMID: 38354929 DOI: 10.1016/j.ijbiomac.2024.130148] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/14/2023] [Revised: 02/03/2024] [Accepted: 02/11/2024] [Indexed: 02/16/2024]
Abstract
Two biobased composite films have been prepared with poly (lactic acid-trimethylene carbonate), polylactic acid and Laponite by solvent evaporation method. The 1H NMR and FTIR spectrums illustrate that P (LA-TMC) polymer is successfully synthesized and designed composite films are produced. Morphometric analyses demonstrate that the roughnesses of the film's surface and cross-section are on the increase with higher PLA and Laponite content. Mechanical performances reveal that the rise in tensile strength and modulus while maintaining excellent elongation at break is mainly due to the increase in the content of polylactic acid and Laponite. By utilizing the nano effect of Laponite, the maximum tensile strength of the composite film reaches 34.59 MPa. Thermal property results illustrate that the Tg and initial decomposition temperature are on the growth with the increase of PLA content. However, it is not significant on the effect of Laponite on the initial decomposition temperature. The water vapor permeability measurements prove that the barrier property of P(LA-TMC)/PLA/Laponite composite film is on the ascent with the Laponite addition. Hydrolytic degradation tests indicate that PLA and Laponite play avital part in accelerating the degradation rate of composite films and alkaline media is superior acidic and neutral conditions.
Collapse
Affiliation(s)
- Shilong Yang
- National and Local Joint Engineering Research Center for Green Preparation Technology of Biobased Materials, Yunnan Minzu University, Kunming 650500, China
| | - Rongying Chen
- National and Local Joint Engineering Research Center for Green Preparation Technology of Biobased Materials, Yunnan Minzu University, Kunming 650500, China
| | - Penghao Zhang
- College of Material Science and Engineering, Changchun University of Technology, Changchun 130000, China
| | - Mingwei Yuan
- National and Local Joint Engineering Research Center for Green Preparation Technology of Biobased Materials, Yunnan Minzu University, Kunming 650500, China
| | - Hongli Li
- National and Local Joint Engineering Research Center for Green Preparation Technology of Biobased Materials, Yunnan Minzu University, Kunming 650500, China.
| | - Dengbang Jiang
- National and Local Joint Engineering Research Center for Green Preparation Technology of Biobased Materials, Yunnan Minzu University, Kunming 650500, China.
| |
Collapse
|
2
|
Wan L, Liu K, Kirillov AM, Fang R, Yang L. Fabrication of Cellulose Filters Incorporating Metal-Organic Frameworks for Efficient Nicotine Adsorption from Cigarette Smoke. LANGMUIR : THE ACS JOURNAL OF SURFACES AND COLLOIDS 2023; 39:5364-5374. [PMID: 37011410 DOI: 10.1021/acs.langmuir.2c03454] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/19/2023]
Abstract
To prevent negative effects of smoking, there is constant research on the development of various types of sustainable filter materials, capable of removing toxic compounds present in cigarette smoke. Because of the extraordinary porosity and adsorption properties, metal-organic frameworks (MOFs) represent promising adsorbents for volatile toxic molecules such as nicotine. This study reports new hybrid materials wherein six types of common MOFs of different porosity and particle size are incorporated into sustainable cellulose fiber from bamboo pulp, resulting in a series of cellulose filter samples abbreviated as MOF@CF. The obtained hybrid cellulose filters were fully characterized and investigated in nicotine adsorption from cigarette smoke, using a specially designed experimental setup. The results revealed that the UiO-66@CF material features the best mechanical performance, facile recyclability, and excellent nicotine adsorption efficiency that attains 90% with relative standard deviations lower than 8.80%. This phenomenon may be caused by the large pore size, open metal sites, and high loading of UiO-66 in cellulose filters. Additionally, the high adsorption capacity showed almost 85% removal of nicotine after the third adsorption cycle. The DFT calculation methods allowed further investigation of the nicotine adsorption mechanism, showing that the energy difference between HOMO and LUMO for UiO-66 was the closest to that of nicotine, which further proves the adsorption ability of nicotine by this material. Owing to the flexibility, recyclability, and excellent adsorption performance, the prepared hybrid MOF@CF materials may find prospective applications in nicotine adsorption from cigarette smoke.
Collapse
Affiliation(s)
- Li Wan
- Key Laboratory of Chemical Additives for China National Light Industry, College of Chemistry and Chemical Engineering, Shaanxi University of Science and Technology, Xi'an 710021, P. R. China
| | - Kunyang Liu
- Key Laboratory of Chemical Additives for China National Light Industry, College of Chemistry and Chemical Engineering, Shaanxi University of Science and Technology, Xi'an 710021, P. R. China
| | - Alexander M Kirillov
- Centro de Química Estrutural, Institute of Molecular Sciences, Departamento de Engenharia Química, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisbon, Portugal
| | - Ran Fang
- Key Laboratory of Chemical Additives for China National Light Industry, College of Chemistry and Chemical Engineering, Shaanxi University of Science and Technology, Xi'an 710021, P. R. China
| | - Lizi Yang
- State Key Laboratory of Applied Organic Chemistry and Key Laboratory of Nonferrous Metals Chemistry and Resources Utilization of Gansu Province, College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000, P. R. China
| |
Collapse
|
3
|
Influence of TEMPO oxidation on the properties of ethylene glycol methyl ether acrylate grafted cellulose sponges. Carbohydr Polym 2021; 272:118458. [PMID: 34420718 DOI: 10.1016/j.carbpol.2021.118458] [Citation(s) in RCA: 9] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/29/2021] [Revised: 06/25/2021] [Accepted: 07/16/2021] [Indexed: 11/21/2022]
Abstract
In this study, cellulose nanofibers (CNF) obtained via high-pressure microfluidization were 2,6,6-tetra-methylpiperidine-1-oxyl (TEMPO) oxidized (TOCNF) in order to facilitate the grafting of ethylene glycol methyl ether acrylate (EGA). FTIR and XPS analyses revealed a more efficient grafting of EGA oligomers on the surface of TOCNF as compared to the original CNF. As a result, a consistent covering of the TOCNF fibers with EGA oligomers, an increased hydrophobicity and a reduction in porosity were noticed for TOCNF-EGA. However, the swelling ratio of TOCNF-EGA was similar to that of original CNF grafted with EGA and higher than that of TOCNF, because the higher amount of grafted EGA onto oxidized cellulose and the looser structure reduced the contacts between the fibrils and increased the absorption of water. All these results corroborated with a good cytocompatibility and compression strength recommend TOCNF-EGA for applications in regenerative medicine.
Collapse
|
4
|
Liu N, Ma Y, Han R, Lv S, Wang P, Luo X. Antifouling biosensors for reliable protein quantification in serum based on designed all-in-one branched peptides. Chem Commun (Camb) 2021; 57:777-780. [PMID: 33355558 DOI: 10.1039/d0cc07220f] [Citation(s) in RCA: 10] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/27/2022]
Abstract
Antifouling electrochemical biosensors based on designed all-in-one branched peptides that combine anchoring, doping, antifouling and recognizing functions were constructed to support sensitive and reliable protein quantification in complex serum samples.
Collapse
Affiliation(s)
- Nianzu Liu
- Key Laboratory of Optic-electric Sensing and Analytical Chemistry for Life Science, MOE, Shandong Key Laboratory of Biochemical Analysis, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| | - Yihui Ma
- Key Laboratory of Optic-electric Sensing and Analytical Chemistry for Life Science, MOE, Shandong Key Laboratory of Biochemical Analysis, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| | - Rui Han
- Key Laboratory of Optic-electric Sensing and Analytical Chemistry for Life Science, MOE, Shandong Key Laboratory of Biochemical Analysis, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| | - Shaoping Lv
- Department of Neurology, Qingdao Central Hospital, Qingdao 266042, China
| | - Peipei Wang
- Department of Neurology, Qingdao Central Hospital, Qingdao 266042, China
| | - Xiliang Luo
- Key Laboratory of Optic-electric Sensing and Analytical Chemistry for Life Science, MOE, Shandong Key Laboratory of Biochemical Analysis, College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| |
Collapse
|
5
|
Selim A, Toth AJ, Fozer D, Süvegh K, Mizsey P. Facile Preparation of a Laponite/PVA Mixed Matrix Membrane for Efficient and Sustainable Pervaporative Dehydration of C1-C3 Alcohols. ACS OMEGA 2020; 5:32373-32385. [PMID: 33376874 PMCID: PMC7758899 DOI: 10.1021/acsomega.0c04380] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 09/08/2020] [Accepted: 11/18/2020] [Indexed: 06/12/2023]
Abstract
The exfoliation method was applied for the preparation of high-water selective mixed matrix membranes (MMMs), especially for the dehydration of C1-C3 alcohol-water solutions. Herein, a facile and easy method was employed to fabricate physically cross-linked Laponite nanosilicate clay-PVA MMMs without additional cross-linking by a one-step synthesis route for water dehydration from methanol, ethanol, and isopropanol aqueous solutions. The morphologies, chemical structures, thermal stabilities, and surface hydrophilicity of Laponite-PVA MMMs were investigated properly by different characterization techniques. The Laponite concentration has affected the fractional free volume of the membranes, as proven by positron annihilation lifetime spectroscopy analysis. The MMMs displayed both a significant improvement in the separation factor and remarkable enhancement in the permeation fluxes for the three alcohol systems. The influence of the operating temperature on the MMM performance was investigated for the methanol/water solution. The methanol permeability was 100-fold lower than that of the water, indicating that the membranes are more water selective. Particularly, the Laponite-PVA membrane with 5 mg/mL Laponite loading exhibits excellent separation efficiency for C1-C3 dehydration having water permeabilities higher than most other polymeric membranes from the other literature studies of 2.82, 2.08, and 1.56 mg m-1 h-1 kPa-1 for methanol, ethanol, and isopropanol/water systems, respectively. This membrane development allows a more efficient and sustainable separation of aqueous alcoholic mixtures.
Collapse
Affiliation(s)
- Asmaa Selim
- Environmental
and Process Engineering Research Group, Department of Chemical and
Environmental Process Engineering, Faculty of Chemical Technology
and Biotechnology, Budapest University of
Technology and Economics, H-1521 Budapest, P.O.B. 91, Hungary
- Chemical
Engineering Department, National Research
Centre, 33 El Buhouth
Street, 12622 Cairo, Egypt
| | - András Jozsef Toth
- Environmental
and Process Engineering Research Group, Department of Chemical and
Environmental Process Engineering, Faculty of Chemical Technology
and Biotechnology, Budapest University of
Technology and Economics, H-1521 Budapest, P.O.B. 91, Hungary
| | - Daniel Fozer
- Environmental
and Process Engineering Research Group, Department of Chemical and
Environmental Process Engineering, Faculty of Chemical Technology
and Biotechnology, Budapest University of
Technology and Economics, H-1521 Budapest, P.O.B. 91, Hungary
| | - Karoly Süvegh
- Laboratory
of Nuclear Chemistry, Eötvös
Loránd University/HAS Chemical Research Center, P.O. Box 32, H-1518, Budapest 112, Hungary
| | - Péter Mizsey
- Environmental
and Process Engineering Research Group, Department of Chemical and
Environmental Process Engineering, Faculty of Chemical Technology
and Biotechnology, Budapest University of
Technology and Economics, H-1521 Budapest, P.O.B. 91, Hungary
- Institute
of Chemistry, University of Miskolc, H-3515 Miskolc, Hungary
| |
Collapse
|
6
|
Selim A, Toth AJ, Fozer D, Szanyi A, Mizsey P. Pervaporative Dehydration of Methanol Using PVA/Nanoclay Mixed Matrix Membranes: Experiments and Modeling. MEMBRANES 2020; 10:membranes10120435. [PMID: 33348791 PMCID: PMC7766437 DOI: 10.3390/membranes10120435] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/18/2020] [Revised: 12/10/2020] [Accepted: 12/14/2020] [Indexed: 11/16/2022]
Abstract
Encouraged by the industrial problem of removing water from methanol solutions, a simple exfoliation method is applied to prepare polyvinyl alcohol (PVA)/laponite nanoclay mixed matrix membranes (MMMs). The membranes are used for the pervaporative dehydration of the methanol-water solution. The influence of the nanoclay content on the pervaporation performance is investigated. The results show that the PVA10 membrane containing 10 wt% Laponite loading exhibits excellent separation efficiency; therefore, all the experimental work is continued using the same membrane. Additionally, the effects of feed concentration and temperature on methanol dehydration performance are thoroughly investigated. The temperatures are ranging from 40–70 °C and the water feed concentrations from 1–15 wt% water. A maximum separation factor of 1120 can be observed at 40 °C and the feed water concentration of 1 wt%. Remarkably, two solution–diffusion models, the Rautenbach (Model I) and modified method by Valentínyi et al. (Model II), are used and compared to evaluate and describe the pervaporation performance of the mixed matrix membrane. Model II proves to be more appropriate for the modeling of pervaporative dehydration of methanol than Model I. This work demonstrates that PVA/nanoclay mixed matrix membranes prepared can efficiently remove water from methanol aqueous solution with pervaporation and the whole process can be accurately modeled with Model II.
Collapse
Affiliation(s)
- Asmaa Selim
- Environmental and Process Engineering Research Group, Department of Chemical and Environmental Process Engineering, Faculty of Chemical Technology and Biotechnology, Budapest University of Technology and Economics, H-1521 Budapest, Hungary; (A.J.T.); (D.F.); (A.S.); (P.M.)
- Chemical Engineering Department, National Research Centre, 33 El Buhouth Street, Cairo 12622, Egypt
- Correspondence: or
| | - András Jozsef Toth
- Environmental and Process Engineering Research Group, Department of Chemical and Environmental Process Engineering, Faculty of Chemical Technology and Biotechnology, Budapest University of Technology and Economics, H-1521 Budapest, Hungary; (A.J.T.); (D.F.); (A.S.); (P.M.)
| | - Daniel Fozer
- Environmental and Process Engineering Research Group, Department of Chemical and Environmental Process Engineering, Faculty of Chemical Technology and Biotechnology, Budapest University of Technology and Economics, H-1521 Budapest, Hungary; (A.J.T.); (D.F.); (A.S.); (P.M.)
| | - Agnes Szanyi
- Environmental and Process Engineering Research Group, Department of Chemical and Environmental Process Engineering, Faculty of Chemical Technology and Biotechnology, Budapest University of Technology and Economics, H-1521 Budapest, Hungary; (A.J.T.); (D.F.); (A.S.); (P.M.)
| | - Péter Mizsey
- Environmental and Process Engineering Research Group, Department of Chemical and Environmental Process Engineering, Faculty of Chemical Technology and Biotechnology, Budapest University of Technology and Economics, H-1521 Budapest, Hungary; (A.J.T.); (D.F.); (A.S.); (P.M.)
- Institute of Chemistry, University of Miskolc, H-3513 Miskolc, Hungary
| |
Collapse
|
7
|
|
8
|
Ghermezcheshme H, Makki H, Mohseni M, Ebrahimi M. Hydrophilic dangling chain interfacial segregation in polyurethane networks at aqueous interfaces and its underlying mechanisms: molecular dynamics simulations. Phys Chem Chem Phys 2020; 22:26351-26363. [PMID: 33179637 DOI: 10.1039/d0cp04244g] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/09/2023]
Abstract
Polymer networks with hydrophilic dangling chains are ideal candidates for many submerged applications, e.g., protein non-adhesive coatings with non-fouling behavior. The dangling chains segregate from the polymer network towards the water and form a brush-like structure at the interface. Several factors such as the polymer network structure, dangling chain length, and water/dangling chain interaction may all affect the interfacial performance of the polymer. Therefore, we employed a Martini based coarse-grained (CG) molecular dynamics (MD) simulation to elucidate the influences of the abovementioned parameters on dangling chain interfacial segregation. We built up several polyurethane (PU) networks based on poly(tetra methylene glycol) (PTMG), as a macrodiol, and methoxy poly(ethylene glycol) (mPEG), as a dangling chain, with varying molecular weights. We found out that the macrodiol/dangling chain length ratio considerably smaller than one impedes the migration of dangling chains towards the water interface, while the dangling chain hydrophilicity and length determine the polymer interfacial layer density/thickness. Then, we artificially changed the dangling chain affinity to water from an intermediate to a very attractive water/dangling chain interaction. We justified that a brush-like structure forms in two consecutive steps: first, a longitudinal, and then a lateral migration of dangling chains in water. The latter step results in a uniform interfacial layer over the polymer interface that mainly occurs in the case of the attractive water/dangling chain interaction.
Collapse
Affiliation(s)
- Hassan Ghermezcheshme
- Department of Polymer and Color Engineering, Amirkabir University of Technology, 424 Hafez Ave., Tehran, Iran.
| | | | | | | |
Collapse
|
9
|
Pervaporative desalination of concentrated brine solution employing crosslinked PVA/silicate nanoclay membranes. Chem Eng Res Des 2020. [DOI: 10.1016/j.cherd.2020.01.015] [Citation(s) in RCA: 14] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022]
|
10
|
Selim A, Toth AJ, Haaz E, Fozer D, Szanyi A, Hegyesi N, Mizsey P. Preparation and characterization of PVA/GA/Laponite membranes to enhance pervaporation desalination performance. Sep Purif Technol 2019. [DOI: 10.1016/j.seppur.2019.03.084] [Citation(s) in RCA: 29] [Impact Index Per Article: 5.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/27/2022]
|
11
|
Venault A, Chang Y. Designs of Zwitterionic Interfaces and Membranes. LANGMUIR : THE ACS JOURNAL OF SURFACES AND COLLOIDS 2019; 35:1714-1726. [PMID: 30001622 DOI: 10.1021/acs.langmuir.8b00562] [Citation(s) in RCA: 50] [Impact Index Per Article: 10.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/28/2023]
Abstract
Zwitterionic materials are the latest generation of materials for nonfouling interfaces and membranes. They outperform poly(ethylene glycol) derivatives because they form tighter bonds with water molecules and can trap more water molecules. This feature article summarizes our laboratory's fundamental developments related to the functionalization of interfaces and membranes using zwitterionic materials. Our molecular designs of zwitterionic polymers and copolymers, sulfobetaine-based, carboxybetaine-based, or phosphobetaine-based, are first reviewed. Then, the strategies used to functionalize surfaces/membranes by coating, grafting onto, grafting from, or in situ modification are examined and discussed, and the third part of this article shifts the focus to key applications of zwitterionic materials. Finally, some potential future directions for molecular designs, functionalization processes, and applications are presented.
Collapse
Affiliation(s)
- Antoine Venault
- Department of Chemical Engineering and R&D Center for Membrane Technology , Chung Yuan Christian University , Chungli District, Taoyuan 320 , Taiwan R.O.C
| | - Yung Chang
- Department of Chemical Engineering and R&D Center for Membrane Technology , Chung Yuan Christian University , Chungli District, Taoyuan 320 , Taiwan R.O.C
| |
Collapse
|
12
|
Cavallaro G, Lazzara G, Lisuzzo L, Milioto S, Parisi F. Filling of Mater-Bi with Nanoclays to Enhance the Biofilm Rigidity. J Funct Biomater 2018; 9:E60. [PMID: 30347894 PMCID: PMC6306923 DOI: 10.3390/jfb9040060] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/26/2018] [Revised: 10/17/2018] [Accepted: 10/18/2018] [Indexed: 01/03/2023] Open
Abstract
We investigated the efficacy of several nanoclays (halloysite, sepiolite and laponite) as nanofillers for Mater-Bi, which is a commercial bioplastic extensively used within food packaging applications. The preparation of Mater-Bi/nanoclay nanocomposite films was easily achieved by means of the solvent casting method from dichloroethane. The prepared bio-nanocomposites were characterized by dynamic mechanical analysis (DMA) in order to explore the effect of the addition of the nanoclays on the mechanical behavior of the Mater-Bi-based films. Tensile tests found that filling Mater-Bi with halloysite induced the most significant improvement of the mechanical performances under traction force, while DMA measurements under the oscillatory regime showed that the polymer glass transition was not affected by the addition of the nanoclay. The tensile properties of the Mater-Bi/halloysite nanotube (HNT) films were competitive compared to those of traditional petroleum plastics in terms of the elastic modulus and stress at the breaking point. Both the mechanical response to the temperature and the tensile properties make the bio-nanocomposites appropriate for food packaging and smart coating purposes. Here, we report a preliminary study of the development of sustainable hybrid materials that could be employed in numerous industrial and technological applications within materials science and pharmaceutics.
Collapse
Affiliation(s)
- Giuseppe Cavallaro
- Dipartimento di Fisica e Chimica, Università degli Studi di Palermo, Viale delle Scienze, pad. 17, 90128 Palermo, Italy.
| | - Giuseppe Lazzara
- Dipartimento di Fisica e Chimica, Università degli Studi di Palermo, Viale delle Scienze, pad. 17, 90128 Palermo, Italy.
| | - Lorenzo Lisuzzo
- Dipartimento di Fisica e Chimica, Università degli Studi di Palermo, Viale delle Scienze, pad. 17, 90128 Palermo, Italy.
| | - Stefana Milioto
- Dipartimento di Fisica e Chimica, Università degli Studi di Palermo, Viale delle Scienze, pad. 17, 90128 Palermo, Italy.
| | - Filippo Parisi
- Dipartimento di Fisica e Chimica, Università degli Studi di Palermo, Viale delle Scienze, pad. 17, 90128 Palermo, Italy.
| |
Collapse
|
13
|
Fetterly CR, Olsen BC, Luber EJ, Buriak JM. Vapor-Phase Nanopatterning of Aminosilanes with Electron Beam Lithography: Understanding and Minimizing Background Functionalization. LANGMUIR : THE ACS JOURNAL OF SURFACES AND COLLOIDS 2018; 34:4780-4792. [PMID: 29614858 DOI: 10.1021/acs.langmuir.8b00679] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/08/2023]
Abstract
Electron beam lithography (EBL) is a highly precise, serial method for patterning surfaces. Positive tone EBL resists enable patterned exposure of the underlying surface, which can be subsequently functionalized for the application of interest. In the case of widely used native oxide-capped silicon surfaces, coupling an activated silane with electron beam lithography would enable nanoscale chemical patterning of the exposed regions. Aminoalkoxysilanes are extremely useful due to their reactive amino functionality but have seen little attention for nanopatterning silicon surfaces with an EBL resist due to background contamination. In this work, we investigated three commercial positive tone EBL resists, PMMA (950k and 495k) and ZEP520A (57k), as templates for vapor-phase patterning of two commonly used aminoalkoxysilanes, 3-aminopropyltrimethoxysilane (APTMS) and 3-aminopropyldiisopropylethoxysilane (APDIPES). The PMMA resists were susceptible to significant background reaction within unpatterned areas, a problem that was particularly acute with APTMS. On the other hand, with both APTMS and APDIPES exposure, unpatterned regions of silicon covered by the ZEP520A resist emerged pristine, as shown both with SEM images of the surfaces of the underlying silicon and through the lack of electrostatically driven binding of negatively charged gold nanoparticles. The ZEP520A resist allowed for the highly selective deposition of these alkoxyaminosilanes in the exposed areas, leaving the unpatterned areas clean, a claim also supported by contact angle measurements with four probe liquids and X-ray photoelectron spectroscopy (XPS). We investigated the mechanistic reasons for the stark contrast between the PMMA resists and ZEP520A, and it was found that the efficacy of resist removal appeared to be the critical factor in reducing the background functionalization. Differences in the molecular weight of the PMMA resists and the resulting influence on APTMS diffusion through the resist films are unlikely to have a significant impact. Area-selective nanopatterning of 15 nm gold nanoparticles using the ZEP520A resist was demonstrated, with no observable background conjugation noted in the unexposed areas on the silicon surface by SEM.
Collapse
Affiliation(s)
- Christopher R Fetterly
- Department of Chemistry , University of Alberta , 11227 Saskatchewan Drive , Edmonton , Alberta T6G 2G2 , Canada
- National Institute for Nanotechnology, National Research Council Canada , 11421 Saskatchewan Drive , Edmonton , Alberta T6G 2M9 , Canada
| | - Brian C Olsen
- Department of Chemistry , University of Alberta , 11227 Saskatchewan Drive , Edmonton , Alberta T6G 2G2 , Canada
- National Institute for Nanotechnology, National Research Council Canada , 11421 Saskatchewan Drive , Edmonton , Alberta T6G 2M9 , Canada
| | - Erik J Luber
- Department of Chemistry , University of Alberta , 11227 Saskatchewan Drive , Edmonton , Alberta T6G 2G2 , Canada
- National Institute for Nanotechnology, National Research Council Canada , 11421 Saskatchewan Drive , Edmonton , Alberta T6G 2M9 , Canada
| | - Jillian M Buriak
- Department of Chemistry , University of Alberta , 11227 Saskatchewan Drive , Edmonton , Alberta T6G 2G2 , Canada
- National Institute for Nanotechnology, National Research Council Canada , 11421 Saskatchewan Drive , Edmonton , Alberta T6G 2M9 , Canada
| |
Collapse
|