Fabrication and Microscopic and Spectroscopic Characterization of Planar, Bimetallic, Micro- and Nanopatterned Surfaces

Calcium carbonate as sorbent for lead removal from wastewaters

Low-cost and largely available industrial by-products such as calcite (CaCO₃) have been considered as sorbents to remediate wastewaters from toxic elements, such as lead, in compliance with the European circular economy strategy. To date few articles are reporting results on lead sorption at the calcite-water solution interface by X-ray photoelectron spectroscopy (XPS) and this investigation aims to clarifying the mechanism of the interaction of Pb²⁺ model solutions over a wide concentration range, from 0.1 μM to 80 mM, with commercial calcite. X-ray powder diffraction (XRPD), scanning electron microscopy (SEM, EDX) and XPS analysis indicate that when CaCO₃ particles are soaked in Pb²⁺ 0.1 mM and 1 mM solutions, hexagonal platelets of hydrocerussite [(PbCO₃)₂ Pb(OH)₂] precipitate on its surface. When the concentration of Pb²⁺ is equal or higher than 40 mM, prismatic acicula of cerussite [PbCO₃] precipitate. Solution analysis by atomic emission spectroscopy (ICP-AES) and ICP-mass spectrometry (ICP-MS) indicate that Pb²⁺ removal efficiency is nearly 100%; when the initial Pb²⁺ concentration was equal to 0.1 μM it was below the limit of detection (LOD) and the efficiency could not be determined. The sorption capacity (q_e) increases linearly with increasing initial Pb²⁺ concentration up to a value of 1680 (20) mg/g when the initial Pb²⁺concentration is 80 mM. These findings suggest that heterogeneous nucleation and surface co-precipitation occur and calcite can be well considered a very promising sorbent for Pb²⁺ removal from wastewaters within a wide initial concentration range.

Measuring the Thickness of Metal Coatings: A Review of the Methods

Thickness dramatically affects the functionality of coatings. Accordingly, the techniques in use to determine the thickness are of utmost importance for coatings research and technology. In this review, we analyse some of the most appropriate methods for determining the thickness of metallic coatings. In doing so, we classify the techniques into two categories: (i) destructive and (ii) non-destructive. We report on the peculiarity and accuracy of each of these methods with a focus on the pros and cons. The manuscript also covers practical issues, such as the complexity of the procedure and the time required to obtain results. While the analysis focuses most on metal coatings, many methods are also applicable to films of other materials.

Model Protective Films on Cu-Zn Alloys Simulating the Inner Surfaces of Historical Brass Wind Instruments by EIS and XPS

The present work focuses on the characterization of brass surfaces after contact with artificial saliva solution at pH 7.4 and phosphate buffer solution at pH 7 simulating two extreme conditions that might occur when playing ancient brass wind instruments in the context of historically informed performance practice. The composition and the morphology of the film formed following the contact with the solutions for 1, 3, and 16 h were investigated by ex situ X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) to shed a light on the surface changes upon time. In situ electrochemical impedance spectroscopy (EIS) was used to study the mechanism of corrosion and protection of the alloys. The results could be interpreted using a reliable equivalent electrical circuit; they provided evidence that the alloys behave differently when in contact to the various solutions. In saliva solution the formation on the brass surface of a thick surface film was observed, composed of crystallites of about 200 nm size mainly composed of CuSCN and Zn₃(PO₄)₂. This layer hinders the alloy dissolution. The contact of the alloys with the buffer solution originated a much thinner layer composed of Cu₂O, ZnO, and a small amount of Zn₃(PO₄)₂. This film is rapidly formed and does not evolve upon time in a protective film.

Influence of Water on Tribolayer Growth When Lubricating Steel with a Fluorinated Phosphonium Dicyanamide Ionic Liquid

This work aims to elucidate the role of environmental humidity on the tribological behavior of steel surfaces lubricated with an ionic liquid comprised of a fluorinated phosphonium cation—tributyl-3,3,4,4,5,5,6,6,7,7,8,8,8-tridecafluoro-octyl-phosphonium—and a dicyanamide anion (i.e. N(CN)2−). Ball-on-disk tribotests were carried out at room temperature and at various levels of relative humidity (RH). Water was found to be required to promote the formation of a tribofilm over the contact area. The reaction layer exhibited a patchy morphology, which resembles that observed formed with conventional antiwear additives such as ZnDTP. A surface-chemical analysis of the tribofilm indicated that the tribofilm is composed of fluorides, oxides, and phosphates, pointing to a stress-induced degradation of the ions and corrosion of the sliding counterparts, which is enabled by the presence of water at the sliding interface.