Aggregation Behavior of the Blends of Homo-PS and PS-b-PEO-b-PS at the Air/Water Interface

Closely Packed Core-Shell Micelle Structures of Double Hydrophilic Miktoarm Star Copolymers at the Air-Water Interface

The aggregation behavior of amphiphilic block copolymers at the air-water interface has been extensively studied, but less attention was given to that of star copolymers. In this work, we studied the interfacial aggregation behavior of two double hydrophilic pH- and temperature-responsive miktoarm star copolymers of poly[di(ethylene glycol) methyl ether methacrylate]-poly[2-(dimethylamino)ethyl methacrylate] (PDEGMA3-PDMAEMA3 and PDEGMA4-PDMAEMA7, the subscripts denote arm numbers) with different molecular weights. The effects of subphase pH and temperature on the monolayer isotherms and hysteresis curves of the two star copolymers and the morphologies of their Langmuir-Blodgett (LB) films were studied by the Langmuir film balance technique and atomic force microscopy, respectively. At the air-water interface, the two star copolymers tend to form closely packed micelles. These micelles exhibit a core-shell structure, where the small hydrophobic core consists of cross-linker of ethylene glycol dimethacrylate (EGDMA) and the carbon backbones of PDEGMA and PDMAEMA arms and the short hydrophilic shell is composed of di(ethylene glycol) and tertiary amine side groups. With increasing subphase pH, the surface pressure versus molecular area isotherms shift toward larger mean molecular areas as a result of the enhanced interface adsorption of nonprotonated tertiary amine groups. The isotherm shift of PDEGMA3-PDMAEMA3 monolayers is primarily attributed to high density of tertiary amine groups in the shells, while that of PDEGMA4-PDMAEMA7 is mainly attributed to high density of di(ethylene glycol) groups in the shells. The hysteresis degrees in the monolayers of the two copolymers under alkaline and neutral conditions are greater than those under acidic conditions due to the decreased protonation degree of the tertiary amine groups. At 10 °C, the mobility of the shells is poor and the isotherms are located on the right. Above the lower critical solution temperature, di(ethylene glycol) groups contract, which causes a slight shift of the isotherms toward smaller mean molecular areas.

Surface Pressure-Induced Interdiffused Structure Evidenced by Neutron Reflectometry in Cellulose Acetate/Polybutadiene Langmuir Films

Binary blends of water-insoluble polymers are a versatile strategy to obtain nanostructured films at the air-water interface. However, there are few reported structural studies of such systems in the literature. Depending on the compatibility of the polymers and the role of the air-water interface, one can expect various morphologies. In that context, we probed Langmuir monolayers of cellulose acetate (CA), of deuterated and postoxidized polybutadiene (PBd) and three mixtures of CA/PBd at various concentrations by coupling surface pressure-area isotherms, Brewster angle microscopy (BAM), and neutron reflectometry at the air-water interface to determine their thermodynamic and structural properties. The homogeneity of the films in the vertical direction, averaged laterally over the spatial coherence length of the neutron beam (∼5 μm), was assessed by neutron reflectometry measurements using D₂O/H₂O subphases contrast-matched to the mixed films. At 5 mN/m, the whole mixed films can be described by a single slightly hydrated thin layer. However, at 15 mN/m, the fit of the reflectivity curves requires a two-layer model consisting of a CA/PBd blend layer in contact with the water, interdiffused with a PBd layer at the interface with air. At intermediate surface pressure (10 mN/m), the determined structure was between those obtained at 5 and 15 mN/m depending on film composition. This PBd enrichment at the air-film interface at high surface pressure, which leads to the PBd depletion in the blend monolayer at the water surface, is attributed to the hydrophobic character of this polymer compared with the predominantly hydrophilic CA.

Poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) Copolymer 2D Single Network at the Air-Water Interface

In this work, Langmuir monolayers based on poly(ethylene glycol)-poly(propylene glycol)-poly(ethylene glycol) (PEG-PPG-PEG) triblock copolymer were in situ stabilized at the air-water interface in the presence of a cross-linking agent, benzene-1,3,5-tricarboxaldehyde (BTC), in the aqueous subphase. The reaction takes place through acid-catalyzed acetalization between the terminal hydroxyl groups of the copolymer and aldehyde functions of the BTC molecules. Mean area per repeat unit measurements as a function of the reaction time show a significant monolayer contraction associated with an increase in its compressibility modulus. In addition, Brewster angle microscopy observations indicate the appearance of higher-density two-dimensional domains, irreversibly formed at constant surface pressure. This is also confirmed on a smaller scale by atomic force microscopy (AFM). These arguments, consistent with copolymer monolayer cross-linking in acidic medium, are supported in situ at the air-water interface by sum-frequency generation (SFG) spectroscopy. Furthermore, PEG-PPG-PEG monolayer cross-linking is not evidenced in alkaline medium, in coherence with the interfacial acid-catalyzed acetalization.