Current Challenges and Perspectives of Polymer Electrolyte Membranes

Different-grain-sized boehmite nanoparticles for stable all-solid-state lithium metal batteries

PEO is one of the common composite polymer electrolyte vehicles; however, the presence of crystalline phase at room temperature, high interface impedance, and low oxidation resistance (<4.0 V) limit its application in stable all-solid-state lithium metal batteries. Herein, we designed a PEO-based solid polymer electrolyte (SPE) by adding boehmite nanoparticles to address the above-mentioned issues. Different-grain-sized boehmite nanoparticles were synthesized by adjusting the hydrothermal temperature. Moreover, the impacts of these distinct grain-sized boehmite nanoparticles used to fabricate boehmite/PEO polymer electrolytes (BPEs) on the performance of all-solid-state lithium metal batteries were investigated. It was found that with the increase in boehmite's grain size, BPEs show better performance. The best BPE exhibited an improved Li+ transference number (0.59), high ionic conductivity (1.25 × 10-4 S m-1), and wide electrochemical window (∼4.5 V) at 60 °C. The assembled lithium symmetric battery can stably undergo 500 hours of lithium plating/stripping at 0.1 mA cm-2. At the same time, the LiFePO4/BPE/Li battery exhibits excellent cycling stability after 100 cycles at 0.5C. This reasonable design strategy with a superior capacity retention rate (86%) demonstrates great potential in achieving high ionic conductivity and good interface stability for all-solid-state lithium metal batteries simultaneously.

An Ultrathin Composite Polymer Electrolyte Dual-Reinforced by a Polymer of Intrinsic Microporosity (PIM-1) and Poly(tetrafluoroethylene) (PTFE) Porous Membrane

The performances of solid-state polymer electrolytes are urgently required to be further improved for high energy density lithium metal batteries. Herein, a highly reinforced ultrathin composite polymer electrolyte (PLPP) is successfully fabricated in a large scale by densely filling the well-dispersed mixture of polyethylene oxide (PEO), Li-salt (LiTFSI) and a polymer of intrinsic microporosity (PIM-1) into porous poly(tetrafluoroethylene) (PTFE) matrix. Based on the macro-plus-micro synergistic enhancement of the PTFE with excellent mechanical properties and the soluble PIM-1 with suitable functional groups, the PLPP electrolyte exhibits excellent properties including mechanical stress, thermal stability, lithium-ion transference number, voltage window and ionic conductivity, which are all superior to the typical PEO/LiTFSI electrolytes. As a result, the Li/PLPP/Li symmetric cell can stably cycle for > 2000 h, and the LiFePO4/PLPP/Li full cell exhibits excellent rate performance (>10 C) and high cycling stability with an initial capacity of 158.8 mAh g-1 and a capacity retention of 78.8% after 300 cycles. In addition, the excellent mechanical properties as well as the wide voltage window reasonably result in the stable operation of full cells with either high-loading cathode up to 28.1 mg cm-2 or high voltage cathode with high energy density.

Advances in ionogels for proton-exchange membranes

To ensure the long-term performance of proton-exchange membrane fuel cells (PEMFCs), proton-exchange membranes (PEMs) have stringent requirements at high temperatures and humidities, as they may lose proton carriers. This issue poses a serious challenge to maintaining their proton conductivity and mechanical performance throughout their service life. Ionogels are ionic liquids (ILs) hybridized with another component (such as organic, inorganic, or organic-inorganic hybrid skeleton). This design is used to maintain the desirable properties of ILs (negligible vapor pressure, thermal stability, and non-flammability), as well as a high ionic conductivity and wide electrochemical stability window with low outflow. Ionogels have opened new routes for designing solid-electrolyte membranes, especially PEMs. This paper reviews recent research progress of ionogels in proton-exchange membranes, focusing on their electrochemical properties and proton transport mechanisms.

Stable and Efficient Dye-Sensitized Solar Cells and Supercapacitors Developed Using Ionic-Liquid-Doped Biopolymer Electrolytes

An ionic liquid (IL) 1-ethyl, 2-methyl imidazolium thiocyanate incorporated biopolymer system is reported in this communication for applications in dual energy devices, i.e., electric double-layer capacitors (EDLCs) and dye-sensitized solar cells (DSSCs). The solution caste method has been used to synthesize ionic-liquid-incorporated biopolymer electrolyte films. The IL mixed biopolymer electrolytes achieve high ionic conductivity up to the order of 10^-3 S/cm with good thermal stability above 250 °C. Electrical, structural, and optical studies of these IL-doped biopolymer electrolyte films are presented in detail. The performance of EDLCs was evaluated using low-frequency electrochemical impedance spectroscopy, cyclic voltammetry, and constant current charge-discharge, while that of DSSCs was assessed using J-V characteristics. The EDLC cells exhibited a high specific capacitance of 200 F/gram, while DSSCs delivered 1.53% efficiency under sun conditions.

Branched Poly(arylene ether ketone sulfone)s with Ultradensely Sulfonated Branched Centers for Proton Exchange Membranes: Effect of the Positions of the Sulfonic Acid Groups

Branched sulfonated polymers present considerable potential for application as proton exchange membranes, yet investigation of branched polymers containing sulfonated branched centers remains to be advanced. Herein, we report a series of polymers with ultradensely sulfonated branched centers, namely, B-x-SPAEKS, where x represents the degree of branching. In comparison with the analogous polymers bearing sulfonated branched arms, B-x-SPAEKS showed a reduced water affinity, resulting in less swelling and lower proton conductivity. The water uptake, swelling ratio (in-plane), and proton conductivity of B-10-SPAEKS at 80 °C were 52.2%, 57.7%, and 23.6% lower than their counterparts, respectively. However, further analysis revealed that B-x-SPAEKS featured significantly better proton conduction under the same water content due to the formation of larger hydrophilic clusters (∼10 nm) that promoted efficient proton transportation. B-12.5-SPAEKS exhibited a proton conductivity of 138.8 mS cm^-1 and a swelling ratio (in-plane) of only 11.6% at 80 °C, both of which were superior to Nafion 117. In addition, a decent single-cell performance of B-12.5-SPAEKS was also achieved. Consequently, the decoration of sulfonic acid groups on the branched centers represents a very promising strategy, enabling outstanding proton conductivity and dimensional stability simultaneously even with low water content.

Synthesis of Sulfonated Polyphenylene Block Copolymers via In Situ Generation of Ni(0)

Proton exchange membranes (PEMs) fabricated from sulfonated polyphenylenes (sPP) exhibit superior proton conductivity and electrochemical performance. However, the Ni(0) catalyst required for Colon's cross-coupling reaction for the synthesis of sPP block copolymers is expensive. Therefore, in this study, we generated Ni(0) in situ from an inexpensive Ni(II) salt in the presence of the reducing metal Zn and NaI. The sPP block copolymers were synthesized from neopentyl-protected 3,5- and 2,5-dichlorobenzenesulfonates and oligo(arylene ether ketone) using the catalyst NiBr₂(PPh₃)₂. The block copolymers synthesized using our strategy and the Ni(0) catalyst exhibited comparable polydispersity index values and high molecular weights. Thin, transparent, and bendable PEMs fabricated using selected high-molecular-weight sPP block copolymers synthesized via our strategy exhibited similar proton conductivities to those of the block copolymers synthesized using the Ni(0) catalyst. We believe that our strategy will promote the synthesis of similar multifunctional block copolymers.

Novel Nafion/Graphitic Carbon Nitride Nanosheets Composite Membrane for Steam Electrolysis at 110 °C

Hydrogen is expected to have an important role in future energy systems; however, further research is required to ensure the commercial viability of hydrogen generation. Proton exchange membrane steam electrolysis above 100 °C has attracted significant research interest owing to its high electrolytic efficiency and the potential to reduce the use of electrical energy through waste heat utilization. This study developed a novel composite membrane fabricated from graphitic carbon nitride (g-C₃N₄) and Nafion and applied it to steam electrolysis with excellent results. g-C₃N₄ is uniformly dispersed among the non-homogeneous functionalized particles of the polymer, and it improves the thermostability of the membranes. The amino and imino active sites on the nanosheet surface enhance the proton conductivity. In ultrapure water at 90 °C, the proton conductivity of the Nafion/0.4 wt.% g-C₃N₄ membrane is 287.71 mS cm^-1. Above 100 °C, the modified membranes still exhibit high conductivity, and no sudden decreases in conductivity were observed. The Nafion/g-C₃N₄ membranes exhibit excellent performance when utilized as a steam electrolyzer. Compared with that of previous studies, this approach achieves better electrolytic behavior with a relatively low catalyst loading. Steam electrolysis using a Nafion/0.4 wt.% g-C₃N₄ membranes achieves a current density of 2260 mA cm^-2 at 2 V, which is approximately 69% higher than the current density achieved using pure Nafion membranes under the same conditions.

Alkali-Stable Anion Exchange Membranes Based on Poly(xanthene)

Poly(xanthene)s (PXs) carrying trimethylammonium, methylpiperidinium, and quinuclidinium cations were synthesized and studied as a new class of anion exchange membranes (AEMs). The polymers were prepared in a superacid-mediated polyhydroxyalkylation involving 4,4'-biphenol and 1-bromo-3-(trifluoroacetylphenyl)-propane, followed by quaternization reactions with the corresponding amines. The architecture with a rigid PX backbone decorated with cations via flexible alkyl spacer chains resulted in AEMs with high ionic conductivity, thermal stability and alkali-resistance. For example, hydroxide conductivities up to 129 mS cm^-1 were reached at 80 °C, and all the AEMs showed excellent alkaline stability with less than 4% ionic loss after treatment in 2 M aq. NaOH at 90 °C during 720 h. Critically, the diaryl ether links of the PX backbone remained intact after the harsh alkaline treatment, as evidenced by both ¹H NMR spectroscopy and thermogravimetry. Our combined findings suggest that PX AEMs are viable materials for application in alkaline fuel cells and electrolyzers.

Room Temperature Halide-Eutectic Solid Electrolytes with Viscous Feature and Ultrahigh Ionic Conductivity

A viscous feature is beneficial for a solid electrolyte with respect to assembling solid-state batteries, which can change the solid-solid contacts from point to face. Here, novel halide-based deep eutectic solid electrolytes (DESEs) prepared by a facile ball milling method is reported. The mixture of halides triggers the deep eutectic phenomena by intermolecular interactions, leading to diverse morphologies and viscous statuses in terms of composition. Chemical- and micro-structure analyses via the cryogenic technique reveal that the LiCl and LiF nanoparticles are dispersed in an amorphous halide matrix, which endow freely mobile ions for fast ion transport. The optimized DESE thus achieves low activation energy and high ionic conductivity of 16 mS cm^-1 at room temperature, one of the highest values among various electrolytes so far. By integrating with the active materials to form a composite cathode, the viscous DESE yields a super-dense composite pellet which possesses intensively enhanced ionic conductivity in contrast to those formed by the sulfide-based electrolyte additives, demonstrating an attractive application prospect.