Crystal Modulus of Poly(glycolic acid) and Its Temperature Dependence

Bio-based epoxidized soybean oil branched cardanol ethers as compatibilizers of polybutylene succinate (PBS)/polyglycolic acid (PGA) blends

Blending poly(butylene succinate) (PBS) with another biodegradable polymer, polyglycolic acid (PGA), has been demonstrated to improve the barrier performance of PBS. However, blending these two polymers poses a challenge because of their incompatibility and large difference of their melting temperatures. In this study, we synthesized epoxidized soybean oil branched cardanol ether (ESOn-ECD), a bio-based and environmentally friendly compatibilizer, and used it to enhance the compatibility of PBS/PGA blends. It was demonstrated that the terminal carboxyl/hydroxyl groups of PBS and PGA can react with ESOn-ECD in situ, leading to branching and chain extension of PBS and PGA. The addition of ESO3-ECD to the blend considerably diminished the dispersed phase of PGA. Specifically, in comparison to the PBS/PGA blend without a compatibilizer, the diameter of the PGA phase decreased from 2.04 μm to 0.45 μm after the addition of 0.7 phr of ESO3-ECD, and the boundary between the two phases became difficult to distinguish. Additionally, the mechanical properties of the blends were improved after addition of ESO3-ECD. This research expands the potential applications of these materials and promotes the use of bio-based components in blend formulations.

Nerve regeneration using decellularized tissues: challenges and opportunities

In tissue engineering, the decellularization of organs and tissues as a biological scaffold plays a critical role in the repair of neurodegenerative diseases. Various protocols for cell removal can distinguish the effects of treatment ability, tissue structure, and extracellular matrix (ECM) ability. Despite considerable progress in nerve regeneration and functional recovery, the slow regeneration and recovery potential of the central nervous system (CNS) remains a challenge. The success of neural tissue engineering is primarily influenced by composition, microstructure, and mechanical properties. The primary objective of restorative techniques is to guide existing axons properly toward the distal end of the damaged nerve and the target organs. However, due to the limitations of nerve autografts, researchers are seeking alternative methods with high therapeutic efficiency and without the limitations of autograft transplantation. Decellularization scaffolds, due to their lack of immunogenicity and the preservation of essential factors in the ECM and high angiogenic ability, provide a suitable three-dimensional (3D) substrate for the adhesion and growth of axons being repaired toward the target organs. This study focuses on mentioning the types of scaffolds used in nerve regeneration, and the methods of tissue decellularization, and specifically explores the use of decellularized nerve tissues (DNT) for nerve transplantation.

In Situ Formation of Microfibrillar PBAT in PGA Films: An Effective Way to Robust Barrier and Mechanical Properties for Fully Biodegradable Packaging Films

Poly(glycolic acid) (PGA) is a semicrystalline biodegradable polyester with high gas barrier properties. However, due to its poor processability and low ductility, PGA could hardly find applications in the packaging field. Here, a strategy was adopted for in situ generation of high-aspect-ratio flexible microfibrils with strong interface affinity for the PGA matrix. Because poly(butylene adipate-co-terephthalate) (PBAT) possesses impressive ductility, it was selected as the "fibrillar toughening phase" to enhance the ductility of PGA. Moreover, a chain extender was used to enhance the interfacial adhesion between the two polymers. The extrusion blown film technique was then used to develop fully biodegradable PGA/PBAT films with a superior combination of excellent barrier performance and robust mechanical properties. The PBAT phase can in situ form microfibrils under the influence of extensional flow. Simultaneously, the synergetic function of the extensional flow field could effectively promote the motion of the PGA molecular chain to develop an oriented crystalline microstructure. Because of the aligned oriented lamellar crystal of PGA and oriented PBAT fibril structures serving as robust "barrier walls" 60PGA/ADR blown films demonstrated dramatically improved resistance to oxygen and water vapor, with 59 and 44 times lower oxygen permeability and water vapor permeability, respectively, when compared to the neat PBAT blown film. As a result, PGA/PBAT blown films offer a variety of benefits, including superior ductility, toughness, and a strong gas barrier property. The potential of these films to degrade makes them a viable contender for replacing classical nondegradable packing films.

The Blending of Poly(glycolic acid) with Polycaprolactone and Poly(l-lactide): Promising Combinations

Poly(glycolic acid) (PGA) holds unique properties, including high gas barrier properties, high tensile strength, high resistance to common organic solvents, high heat distortion temperature, high stiffness, as well as fast biodegradability and compostability. Nevertheless, this polymer has not been exploited at a large scale due to its relatively high production cost. As such, the combination of PGA with other bioplastics on one hand could reduce the material final cost and on the other disclose new properties while maintaining its “green” features. With this in mind, in this work, PGA was combined with two of the most widely applied bioplastics, namely poly(l-lactide) (PLLA) and poycaprolactone (PCL), using the melt blending technique, which is an easily scalable method. FE-SEM measurements demonstrated the formation of PGA domains whose dimensions depended on the polymer matrix and which turned out to decrease by diminishing the PGA content in the mixture. Although there was scarce compatibility between the blend components, interestingly, PGA was found to affect both the thermal properties and the degradation behavior of the polymer matrices. In particular, concerning the latter property, the presence of PGA in the blends turned out to accelerate the hydrolysis process, particularly in the case of the PLLA-based systems.

Structural Evolution of Polyglycolide and Poly(glycolide-co-lactide) Fibers during the Heat-Setting Process

PGA and P(GA-co-LA) fibers applied as surgical sutures strongly depend on their microstructure. The structural evolution in both the relaxed and tensioned states during heat-setting after hot stretching, which included heating and postannealing, was investigated using in situ WAXD/SAXS and DSC techniques. We found that the fibers of both PGA and P(GA-co-LA) with 8% LA content under the relaxed state were more advantageous than the fibers under the tensioned state indicated by the larger crystallite sizes and unit cell parameters and the higher crystallinity. The mechanical properties of the samples increased after heat-setting. Heat-setting at 120 °C was more suitable for promoting the fiber properties, which can be ascribed to crystal formation and perfection. During the heating, the thermal expansion increased the unit cell parameters and the long period of PGA linearly, whereas the unit cell parameters of P(GA-co-LA) had an obvious turning point at 60-80 °C, and the long period showed a sudden decline in the temperature range of 60-80 °C, which was mainly the result of the discharge of LA units. The unit cell parameters and the long period of both PGA and P(GA-co-LA) decreased during the isotherm process due to crystal perfection. However, the P(GA-co-LA) decrease was more prominent than PGA because of the inclusion of LA monomers in the crystal structure of GAs.

Kinetic Study of Depolymerization of Lactic and Glycolic Acid Oligomers in the Presence of Oxide Catalysts

For glycolic acid oligomers (GAO): l-lactic acid oligomers (LAO) mixtures, as an example, it was shown that the nature of the active sites of the catalysts significantly affect the depolymerization process. So, ZnO, which has mainly basic sites, leads to the highest yield of cyclic diesters. On the contrary, depolymerization in the presence of acidic γ-Al₂O₃ and without a catalyst is characterized by lower diester yields due to the prevalence of a side polycondensation reaction. Using GAO:LAO mixtures, it was shown that in the case of three studied systems (with ZnO, γ-Al₂O₃, and without catalyst), mixed interactions occurred, including homo-paired and hetero-paired intermolecular interactions, as well as intramolecular interactions of oligomeric molecules. Kinetic models of the processes under study were determined by isoconversional thermal analysis. In the case of depolymerization of oligomers in the presence of ZnO, the kinetic model was between the kinetic models of the first (F1) and second (F2) orders, while in depolymerization in the presence of γ-Al₂O₃ and without a catalyst, the process was described by diffusion models such as the Jander equation (D3) and Zhuravlev, Lesokin, Tempelman equation (D5).

Zero-valent iron nanoparticles containing nanofiber scaffolds for nerve tissue engineering

Regeneration of nerve tissue is a challenging issue in regenerative medicine. Especially, the peripheral nerve defects related to the accidents are one of the leading health problems. For large degeneration of peripheral nerve, nerve grafts are used in order to obtain a connection. These grafts should be biodegradable to prevent second surgical intervention. In order to make more effective nerve tissue engineering materials, nanotechnological improvements were used. Especially, the addition of electrically conductive and biocompatible metallic particles and carbon structures has essential roles in the stimulation of nerves. However, the metabolizing of these structures remains to wonder because of their nondegradable nature. In this study, biodegradable and conductive nerve tissue engineering materials containing zero-valent iron (Fe) nanoparticles were developed and investigated under in vitro conditions. By using electrospinning technique, fibrous mats composed of electrospun poly(ε-caprolactone) (PCL) nanofibers and Fe nanoparticles were obtained. Both electrical conductivity and mechanical properties increased compared with control group that does not contain nanoparticles. Conductivity of PCL/Fe5 and PCL/Fe10 increased to 0.0041 and 0.0152 from 0.0013 Scm^-1 , respectively. Cytotoxicity results indicated toxicity for composite mat containing 20% Fe nanoparticles (PCL/Fe20). SH-SY5Y cells were grown on PCL/Fe10 best, which contains 10% Fe nanoparticles. Beta III tubulin staining of dorsal root ganglion neurons seeded on mats revealed higher cell number on PCL/Fe10. This study demonstrated the impact of zero-valent Fe nanoparticles on nerve regeneration. The results showed the efficacy of the conductive nanoparticles, and the amount in the composition has essential roles in the promotion of the neurites.

Tailoring synthetic polymeric biomaterials towards nerve tissue engineering: a review

The nervous system is known as a crucial part of the body and derangement in this system can cause potentially lethal consequences or serious side effects. Unfortunately, the nervous system is unable to rehabilitate damaged regions following seriously debilitating disorders such as stroke, spinal cord injury and brain trauma which, in turn, lead to the reduction of quality of life for the patient. Major challenges in restoring the damaged nervous system are low regenerative capacity and the complexity of physiology system. Synthetic polymeric biomaterials with outstanding properties such as excellent biocompatibility and non-immunogenicity find a wide range of applications in biomedical fields especially neural implants and nerve tissue engineering scaffolds. Despite these advancements, tailoring polymeric biomaterials for design of a desired scaffold is fundamental issue that needs tremendous attention to promote the therapeutic benefits and minimize adverse effects. This review aims to (i) describe the nervous system and related injuries. Then, (ii) nerve tissue engineering strategies are discussed and (iii) physiochemical properties of synthetic polymeric biomaterials systematically highlighted. Moreover, tailoring synthetic polymeric biomaterials for nerve tissue engineering is reviewed.