Graphene/Graphitized Polydopamine/Carbon Nanotube All-Carbon Ternary Composite Films with Improved Mechanical Properties and Through-Plane Thermal Conductivity

SPI-Modified h-BN Nanosheets-Based Thermal Interface Materials for Thermal Management Applications

The rising concern over the usage of electronic devices and the operating environment requires efficient thermal interface materials (TIMs) to take away the excess heat generated from hotspots. TIMs are crucial in dissipating undesired heat by transferring energy from the source to the heat sink. Silicone oil (SO)-based composites are the most used TIMs due to their strong bonding and oxidation resistance. However, thermal grease performance is unreliable due to aging effects, toxic chemicals, and a higher percentage of fillers. In this work, TIMs are prepared using exfoliated hexagonal boron nitride nanosheets (h-BNNS) as a nanofiller, and they were functionalized by ecofriendly natural biopolymer soy protein isolate (SPI). The exfoliated h-BNNS has an average lateral size of ∼266 nm. The functionalized h-BNNS/SPI are used as fillers in the SO matrix, and composites are prepared using solution mixing. Hydrogen bonding is present between the organic chain/oxygen in silicone polymer, and the functionalized h-BNNS are evident from the FTIR measurements. The thermal conductivity of h-BNNS/SPI/SO was measured using the modified transient plane source (MTPS) method. At room temperature, the maximum thermal conductivity is 1.162 Wm-1K-1 (833% enhancement) at 50 wt % of 3:1 ratio of h-BNNS:SPI, and the thermal resistance (TR) of the composite is 5.249 × 106 K/W which is calculated using the Foygel nonlinear model. The heat management application was demonstrated by applying TIM on a 10 W LED bulb. It was found that during heating, the 50 wt % TIM decreases the surface temperature of LED by ∼6 °C compared with the pure SO-based TIM after 10 min of ON condition. During cooling, the modified TIM reduces the surface temperature by ∼8 °C under OFF conditions within 1 min. The results indicate that natural polymers can effectively stabilize and link layered materials, enhancing the efficiency of TIMs for cooling electronics and LEDs.

Highly Sensitive Weaving Sensor of Hybrid Graphene Nanoribbons and Carbon Nanotubes for Enhanced Pressure Sensing Function

Carbon nanotubes (CNTs) hold great promise in next-generation sensors because of their remarkable physical properties. Yet, maintaining precise stacking configurations of CNTs to make full use of their remarkable properties is challenging because of their susceptibility to spontaneous reconstruction. Inspired by the weaving technology, we propose a CNT-graphene nanoribbon hybrid woven model that can maintain the specific structure of CNTs to achieve their elaborately designed function. In this study, comprehensive molecular dynamics simulations are carried out to investigate the thermal stability of the CNT-graphene hybrid woven model, as well as their potential for pressure sensing applications by utilizing the unique response of thermal transport to mechanical deformation at heterojunctions. The thermal stability is sensitive to the size of the graphene nanoribbon, and the woven structure remains stable from 200-500 K when its width is greater than 2.0 nm. Moreover, it is exciting that the sensors are effective at predicting the shapes of externally loaded objects through the analysis of the thermal conductivity distribution, which can be derived from the relationship between the thermal conduction and the pressure. Our findings shed light on the bottom-up functional design of nanomaterials and expand wider applications of high-performance nanosensors in other related fields.

Laser-Induced Graphitization of Polydopamine on Titania Nanotubes

Since the discovery of laser-induced graphite/graphene, there has been a notable surge of scientific interest in advancing diverse methodologies for their synthesis and applications. This study focuses on the utilization of a pulsed Nd:YAG laser to achieve graphitization of polydopamine (PDA) deposited on the surface of titania nanotubes. The partial graphitization is corroborated through Raman and XPS spectroscopies and supported by water contact angle, nanomechanical, and electrochemical measurements. Reactive molecular dynamics simulations confirm the possibility of graphitization in the nanosecond time scale with the evolution of NH3, H2O, and CO2 gases. A thorough exploration of the lasing parameter space (wavelength, pulse energy, and number of pulses) was conducted with the aim of improving either electrochemical activity or photocurrent generation. Whereas the 532 nm laser pulses interacted mostly with the PDA coating, the 365 nm pulses were absorbed by both PDA and the substrate nanotubes, leading to a higher graphitization degree. The majority of the photocurrent and quantum efficiency enhancement is observed in the visible light between 400 and 550 nm. The proposed composite is applied as a photoelectrochemical (PEC) sensor of serotonin in nanomolar concentrations. Because of the suppressed recombination and facilitated charge transfer caused by the laser graphitization, the proposed composite exhibits significantly enhanced PEC performance. In the sensing application, it showed superior sensitivity and a limit of detection competitive with nonprecious metal materials.

Immobilized nickel boride nanoparticles on magnetic functionalized multi-walled carbon nanotubes: a new nanocomposite for the efficient one-pot synthesis of 1,4-benzodiazepines

In this study, a new magnetic nanocomposite consisting of Ni2B nanoparticles anchored on magnetic functionalized multi-walled carbon nanotubes (Fe3O4/f-MWCNT/Ni2B) was synthesized and characterized using various techniques such as FT-IR, XRD, FESEM, SEM-based EDX, SEM-based elemental mapping, HRTEM, DLS, SAED, XPS, BET, TGA, and VSM. The as-prepared magnetic nanocomposite was successfully employed for the preparation of bioactive 1,4-benzodiazepines from the three-component reaction of o-phenylenediamine (1), dimedone (2), and different aldehydes (3), in polyethylene glycol 400 (PEG-400) as a solvent at 60 °C. The obtained results demonstrated that the current one-pot three-component protocol offers many advantages, such as good-to-excellent yields within acceptable reaction times, favorable TONs and TOFs, eco-friendliness of the procedure, easy preparation of the nanocomposite, mild reaction conditions, a broad range of products, excellent catalytic activity, green solvent, and reusability of the nanocomposite.

Acid enhanced zipping effect to densify MWCNT packing for multifunctional MWCNT films with ultra-high electrical conductivity

The outstanding electrical and mechanical properties remain elusive on macroscopic carbon nanotube (CNT) films because of the difficult material process, which limits their wide practical applications. Herein, we report high-performance multifunctional MWCNT films that possess the specific electrical conductivity of metals as well as high strength. These MWCNT films were synthesized by a floating chemical vapor deposition method, purified at high temperature and treated with concentrated HCl, and then densified due to the developed chlorosulfonic acid-enhanced zipping effect. These large scalable films exhibit high electromagnetic interference shielding efficiency, high thermoelectric power factor, and high ampacity because of the densely packed crystalline structure of MWCNTs, which are promising for practical applications.

Significantly enhanced thermally conductive epoxy composite composed of caterpillar-like structured expanded graphite/ boron nitride nanotubes

The trend toward miniaturization, integration and multifunctionality of modern electronics has led to a rapid increase in power density, which makes heat dissipation a critical issue. Despite the great potential of graphite-related nanocomposites in dissipating excess heat to ensure high efficiency and long lifetime of electronic devices, the practical application of these composites is limited by the ultra-low vertical thermal conductivity due to the interfacial thermal resistance between graphite layers. Here, a caterpillar-like hybrid filler was fabricated by the in situ intercalation of boron nitride nanotubes (BNNTs) between expanded graphite (EG) layers based on chemical vapor deposition technology. Owing to the optimized interfacial thermal resistance by forming covalent C-N bonding at the interface of EG and BNNT, the through-plane thermal conductivity of epoxy-based nanocomposites can be up to 5.18 Wm−1 K−1. In addition, the composite possessed electromagnetic interference shielding performance of 33.34 dB while maintaining electrical insulation due to the hierarchical structure. This work provided a new strategy for fabricating polymer-based composites with excellent through-plane thermal conductivity in thermal management applications.

Multi-nanocavities and multi-defects synergetic enhancement for the electromagnetic absorption of the rGO-NG film

Dielectric loss is an important way to eliminate electromagnetic pollution. In order to achieve high dielectric loss, a graphene film reduced graphene oxide-N doped graphene (rGO-NG) was constructed from graphene oxide-Ni@polydopamine (GO-Ni@PDA) via thein situsynthesis of hollow graphene spheres between graphene sheets. Thisin situwas achieved by means of electrostatic self-assembly and metal-catalyzed crystallization. Owing to the synergetic effect of multi-nanocavities and multi-defects, the prepared rGO-NG film shows an average shielding effectiveness (SE) of 50.0 dB in the range of 8.2-12.4 GHz with a thickness of 12.2μm, and the SE reflection is only 7.3 dB on average. It also exhibits an average dielectric loss tangent (tanδ) of 23.1, which is 26 and 105 times higher than those of rGO and rGO-Ni, respectively. This work provides a simple but effective route to develop high performance graphene-based materials for application as an electromagnetic interference shielding film in today's electronic devices.

Highly Thermal Conductive Graphite Films Derived from the Graphitization of Chemically Imidized Polyimide Films

With the large-scale application and high-speed operation of electronic equipment, the thermal diffusion problem presents an increasing requirement for effective heat dissipation materials. Herein, high thermal conductive graphite films were fabricated via the graphitization of polyimide (PI) films with different amounts of chemical catalytic reagent. The results showed that chemically imidized PI (CIPI) films exhibit a higher tensile strength, thermal stability, and imidization degree than that of purely thermally imidized PI (TIPI) films. The graphite films derived from CIPI films present a more complete crystal orientation and ordered arrangement. With only 0.72% chemical catalytic reagent, the graphitized CIPI film achieved a high thermal conductivity of 1767 W·m⁻¹·K⁻¹, which is much higher than that of graphited TIPI film (1331 W·m⁻¹·K⁻¹), with an increase of 32.8%. The high thermal conductivity is attributed to the large in-plane crystallite size and high crystal integrity. It is believed that the chemical imidization method prioritizes the preparation of high-quality PI films and helps graphite films achieve an excellent performance.

Structure development of carbon-based solar-driven water evaporation systems

Pressing need goes ahead for accessing freshwater in insufficient supply countries and regions, which will become a restrictive factor for human development and production. In recent years, solar-driven water evaporation (SDWE) systems have attracted increasing attention for their specialty in no consume conventional energy, pollution-free, and the high purity of fresh water. In particular, carbon-based photothermal conversion materials are preferred light-absorbing material for SDWE systems because of their wide range of spectrum absorption and high photothermal conversion efficiency based on super-conjugate effect. Until now, many carbon-based SDWE systems have been reported, and various structures emerged and were designed to enhance light absorption, optimize heat management, and improve the efficient water transport path. In this review, we attempt to give a comprehensive summary and discussions of structure progress of the carbon-based SDWE systems and their working mechanisms, including carbon nanoparticles systems, single-layer photothermal membrane systems, bi-layer structural photothermal systems, porous carbon-based materials systems, and three dimensional (3D) systems. In these systems, the latest 3D systems can expand the light path by allowing light to be reflected multiple times in the microcavity to increase the light absorption rate, and its large heat exchange area can prompt more water to evaporate, which makes them the promising application foreground. We hope our review can spark the probing of underlying principles and inspiring design strategies of these carbon-based SDWE systems, and further guide device optimizations, eventually promoting in extensive practical applications in the future.

Stitching Graphene Sheets with Graphitic Carbon Nitride: Constructing a Highly Thermally Conductive rGO/g-C3N4 Film with Excellent Heating Capability

Driven by the evolution of electronic packaging technology for high-dense integration of high-power, high-frequency, and multi-function devices in modern electronics, thermal management materials have become a crucial component for guaranteeing the stable and reliable operation of devices. Because of its admirable in-plane thermal conductivity, graphene is considered as a desired thermal conductor. However, the promise of graphene films has been greatly weakened as the existence of grain boundaries lead to a high extent of phonon scattering. Here, a stitching strategy is adopted to fabricate an rGO/g-C₃N₄ film, where 2D g-C₃N₄ works as a linker to covalently connect adjacent rGO sheets for expanding the size of graphene and forming an in-plane rGO/g-C₃N₄ heterostructure. The in-plane thermal conductivity of the rGO/g-C₃N₄ film reaches 41.2 W m^-1 K^-1 at a g-C₃N₄ content of only 1 wt %, which increased by 17.3% compared to pristine rGO. The interfaced thermal resistance between rGO and g-C₃N₄ is further examined by non-equilibrium molecular dynamics simulations. Furthermore, owing to the unique light absorption and welding ability of g-C₃N₄, the rGO/g-C₃N₄ film presents superior solar-thermal and electric-thermal responses to controllably regulate the chip temperature against overcooling. This work provides a facile approach to construct a large-sized rGO sheet and combines heat dissipation and heating capability in the same thermal management material for future electronics.