In Situ Construction of Bifunctional N-Doped Carbon-Anchored Co Nanoparticles for OER and ORR

Fe-Co Co-Doped 1D@2D Carbon-Based Composite as an Efficient Catalyst for Zn-Air Batteries

A Fe-Co dual-metal co-doped N containing the carbon composite (FeCo-HNC) was prepared by adjusting the ratio of iron to cobalt as well as the pyrolysis temperature with the assistance of functionalized silica template. Fe1Co-HNC, which was formed with 1D carbon nanotubes and 2D carbon nanosheets including a rich mesoporous structure, exhibited outstanding oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalytic activities. The ORR half-wave potential is 0.86 V (vs. reversible hydrogen electrode, RHE), and the OER overpotential is 0.76 V at 10 mA cm-2 with the Fe1Co-HNC catalyst. It also displayed superior performance in zinc-air batteries. This method provides a promising strategy for the fabrication of efficient transition metal-based carbon catalysts.

High quality bifunctional cathode for rechargeable zinc-air batteries using N-doped carbon nanotubes constrained CoFe alloy

Building efficient and stable bifunctional electrocatalysts toward oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) is crucial for the advancement of rechargeable zinc-air batteries (ZABs). Here, a convenient in situ strategy is reported to controllably encapsulate CoFe alloy nanoparticles within N-doped carbon nanotubes (CoFe@NCNT). The abundant Co(Fe)-Nx active sites and the synergistic interaction between CoFe alloys and carbon nanotubes facilitate mass transfer and interfacial charge transfer, resulting in excellent dual functional electrocatalytic activity of OER/ORR with minor potential difference (ΔE = 0.73 V). Thus, the corresponding rechargeable ZAB displays high power density (194 mW cm-2), excellent specific capacity (795 mAh gZn-1), and favorable stability (900 cycles@5 mA cm-2). This work provides an approach for establishing low-cost bultifunctional electrocatalysts with excellent performance of non-noble metal nanoalloys.

Regulating the frontier orbital of iron phthalocyanine with nitrogen doped carbon nanosheets for improving oxygen reduction activity

Iron phthalocyanine (FePc) has attracted widespread attention for its tunable electronic structure. However, the Fe-N sites suffer from undesirable oxygen reduction activity due to the symmetric geometries. A suitable substrate was thus needed to induce electron redistribution around Fe-N to improve the activity. Herein, ultrathin nitrogen-doped carbon nanosheets (N-CNSs) were prepared by a simple high temperature pyrolysis. Then iron phthalocyanine was loaded on the ultrathin nitrogen-doped carbon nanosheets (FePc@N-CNSs) by a low-cost and simple solution method. This composite catalyst shows an excellent ORR activity with a half potential of 0.88 V, an onset potential of 0.99 V and durability superior to commercial Pt/C. When used as an air cathode catalyst for rechargeable zinc-air batteries, FePc@N-CNS modified batteries outperform Pt/C + RuO2 modified batteries with higher power density and superior constant current charge-discharge cycling stability of 37 hours. The regulated electronic structure of FePc by the N-CNS substrate was revealed further by DFT calculations, which explained the enhanced adsorption of the active center to the intermediates and the increased ORR performance.

MnS-BaS Heterostructures as Effective Catalysts for Oxygen Reduction Reaction

The inadequate electrical conductivity of metal sulfides, along with their tendency to agglomerate, has hindered their use in energy storage and catalysis. The construction of a heterojunction can ameliorate these deficiencies to some extent. In this paper, MnS-BaS heterojunction catalysts were prepared by a hydrothermal method, which is a simple and inexpensive process. The MnS-BaS heterojunction catalysts exhibited superior performance owing to the strong synergistic interaction between MnS and BaS. Density functional theory (DFT) calculations reveal strong interactions at the heterojunction interface and significant electron transfer between MnS and BaS, which further modulates the electronic structure of Mn. The elevation of the center of the d-band enhances the adsorption of oxygen and oxygen-containing intermediates on the catalyst, thus promoting the oxygen reduction reaction (ORR). The practical application of MnS-BaS catalysts was tested by assembling zinc-air batteries. This study provides a rational strategy for designing transition metal catalysts that are efficient and low cost.

Geometric and Electronic Engineering in Co/VN Nanoparticles to Boost Bifunctional Oxygen Electrocatalysis for Aqueous/Flexible Zn-Air Batteries

Modulating metal-metal and metal-support interactions is one of the potent tools for augmenting catalytic performance. Herein, highly active Co/VN nanoparticles are well dispersed on three-dimensional porous carbon nanofoam (Co/VN@NC) with the assistance of dicyandiamide. Studies certify that the consequential disordered carbon substrate reinforces the confinement of electrons, while the coupling of diverse components optimizes charge redistribution among species. Besides, theoretical analyses confirm that the regulated electron configuration can significantly tune the binding strength between the active sites and intermediates, thus optimizing reaction energy barriers. Therefore, Co/VN@NC exhibits a competitive potential difference (ΔE, 0.65 V) between the half-wave potential of ORR and OER potential at 10 mA cm-2, outperforming Pt/C+RuO2 (0.67 V). Further, catalyst-based aqueous/flexible ZABs present superior performances with peak power densities of 156 and 85 mW cm-2, superior to Pt/C-based counterparts (128 and 73 mW cm-2). This research provides a pivotal foundation for the evolution of bifunctional catalysts in the energy sector.

Rare-Earth-Modified NiS2 Improves OH Coverage for an Industrial Alkaline Water Electrolyzer

The low coverage rate of anode OH adsorption under high current density conditions has become an important factor restricting the development of an industrial alkaline water electrolyzer (AWE). Here, we present our rare earth modification promotion strategy on using the rare earth oxygen-friendly interface to increase the OH coverage of the NiS2 surface for efficient AWE anode catalysis. Density functional theory calculations predict that rare earths can enhance the coverage of surface OH, and the synthesis reaction mechanism is discussed in the synthesis process spectrum. Experimentally, by preparing a series of rare-earth-modified NiS2, the relationship between OH coverage, active site density, and catalytic activity was established by attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy, time-resolved absorption spectra, and so on. The unique oxygenophilic properties of rare earths enhance OH coverage, thereby increasing the density of active sites for efficient catalysis. Furthermore, Eu2O3/NiS2 was assembled into the AWE equipment and operated stably for over 240 h at a current density of 300 mA cm-2 under industrial conditions of 80 °C and 30% KOH. Rare-earth-modified NiS2 exhibits better catalytic activity than traditional non-noble metal anode catalysts Ni(OH)2 and NiS2, providing a new approach for rare earth promotion to solve the problem of low OH coverage in the AWE anode.

Low-Potential Iodide Oxidation Enables Dual-Atom CoFe─N─C Catalysts for Ultra-Stable and High-Energy-Efficiency Zn-Air Batteries

The low energy efficiency and limited cycling life of rechargeable Zn-air batteries (ZABs) arising from the sluggish oxygen reduction/evolution reactions (ORR/OERs) severely hinder their commercial deployment. Herein, a zeolitic imidazolate framework (ZIF)-derived strategy associated with subsequent thermal fixing treatment is proposed to fabricate dual-atom CoFe─N─C nanorods (Co1 Fe1 ─N─C NRs) containing atomically dispersed bimetallic Co/Fe sites, which can promote the energy efficiency and cyclability of ZABs simultaneously by introducing the low-potential oxidation redox reactions. Compared to the mono-metallic nanorods, Co1 Fe1 ─N─C NRs exhibit remarkable ORR performance including a positive half-wave potential of 0.933 V versus reversible hydrogen electrode (RHE) in alkaline electrolyte. Surprisingly, after introducing the potassium iodide (KI) additive, the oxidation overpotential of Co1 Fe1 ─N─C NRs to reach 10 mA cm-2 can be significantly reduced by 395 mV compared to the conventional destructive OER. Theoretical calculations show that the markedly decreased overpotential of iodide oxidation can be ascribed to the synergistic effects of neighboring Co─Fe diatomic sites as the unique adsorption sites. Overall, aqueous ZABs assembled with Co1 Fe1 ─N─C NRs and KI as the air-cathode catalyst and electrolyte additive, respectively, can deliver a low charging voltage of 1.76 V and ultralong cycling stability of over 230 h with a high energy efficiency of ≈68%.

Electrochemical production of hydrogen peroxide by non-noble metal-doped g-C3N4 under a neutral electrolyte

Electrochemical oxygen reduction (ORR) for the production of clean hydrogen peroxide (H2O2) is an effective alternative to industrial anthraquinone methods. The development of highly active, stable, and 2e- ORR oxygen reduction electrocatalysts while suppressing the competing 4e- ORR pathway is currently the main challenge. Herein, bimetallic doping was successfully achieved based on graphitic carbon nitride (g-C3N4) with the simultaneous introduction of K and Co, whereby 2D porous K-Co/CNNs nanosheets were obtained. The introduction of Co promoted the selectivity for H2O2, while the introduction of K not only promoted the formation of 2D nanosheets of g-C3N4, but also inhibited the ablation of H2O2 by K-Co/CNNs. Electrochemical studies showed that the selectivity of H2O2 in K-Co/CNNs under neutral electrolyte was as high as 97%. After 24 h, the H2O2 accumulation of K-Co/CNNs was as high as 31.7 g L-1. K-Co/CNNs improved the stability of H2O2 by inhibiting the ablation of H2O2, making it a good 2e- ORR catalyst and providing a new research idea for the subsequent preparation of H2O2.

Redox-active ligands enhance oxygen evolution reaction activity: Regulating the spin state of ferric ions and accelerating electron transfer

Metal-organic frameworks (MOFs) are considered as one of the most promising catalysts for oxygen evolution reaction (OER). However, only a few have introduced redox-active ligands into MOFs and explored their role in the OER process. In this work, we synthesized FeNi DHBQ/NF using the redox-active ligand 2,5-dihydroxy-1,4-benzoquinone (DHBQ), which exhibited excellent redox activity and required only 207 and 242 mV overpotentials to achieve current densities of 10 and 100 mA cm-2. Our research confirms that (i) the doping of Fe leads to the formation of Ni → O → Fe electron transfer channels in the MOFs and stronger electron transfer, attributed to the stronger d-π conjugation between the metal center and the ligand and reduced the d-orbital crystal field splitting energy of Fe3+; (ii) the rate determination step (RDS) in the OER process of the catalyst is the formation of O*, while Fe and redox-active ligands effectively regulate the adsorption energy of oxygen-containing intermediates, reducing the energy barrier of the RDS; (iii) the redox-active ligands can act as "electron reservoirs" in the electrochemical process, making Ni more readily oxidized to Ni3+ or even Ni4+ at low potentials, which is beneficial to the subsequent OER process.

Anchoring a Pt-based alloy on oxygen-vacancy-defected MXene nanosheets for efficient hydrogen evolution reaction and oxygen reduction reaction

Rational design and controllable synthesis of Pt-based materials with intimate interfacial contact open up the possibility for boosting the performance of the ORR (oxygen reduction reaction) and HER (hydrogen evolution reaction). However, it is still challenging to prevent the oxidation of Pt during the formation of alloys and to clarify the interfacial synergistic effects on the catalytic performance between Pt alloys and the dispersed substrate. Herein, the wet chemical stripping and intercalation methods were employed to synthesize a two-dimensional (2D) MXene with abundant defect sites, which can anchor Pt3Co/Pt3Ni nanoparticles and prevent the oxidation of Pt during the process of atomic rearrangement at high temperatures. The obtained Pt3Co/MXene and Pt3Ni/MXene displayed different phase compositions and alloying degrees on adjusting the annealing temperature. Electrochemical test results showed that the optimized HER and ORR electrocatalytic activities occurred at 700 °C. Compared with Pt3Ni/MXene-700, Pt3Co/MXene-700 exhibited an HER overpotential of 1.3 mV at a current density of 10 mA cm-2, and a Tafel slope of 27.11 mV dec-1 in 0.1 M HClO4 solution. Furthermore, Pt3Co/MXene-700 exhibited an ORR half-wave potential of 0.897 V, and a mass activity of 241.1 mA mg-1Pt in 0.1 M HClO4 solution. This can be attributed to the formation of intermetallic compounds in Pt3Co/MXene. The electronic structure analysis showed that the enhanced performance could be assigned to the electron-capturing capability of the MXene, less oxidation of Pt and synergistic interactions between the Pt alloy and the MXene substrate. These findings provide a new strategy for the synthesis of highly active HER/ORR catalysts and broaden the way for the design of MXene-based catalysts.

A 3D Covalent Organic Framework with In-situ Formed Pd Nanoparticles for Efficient Electrochemical Oxygen Reduction

Non-platinum noble metals are highly desirable for the development of highly active, stable oxygen reduction reaction (ORR) electrocatalysts for fuel cells and metal-air batteries. However, how to improve the utilization of non-platinum noble metals is an urgent issue. Herein, a highly efficient catalyst for ORR was prepared through homogeneous loading of Pd precursors by a domain-limited method in a three-dimensional covalent organic framework (COF) followed by pyrolysis. The morphology of the Pd nanoparticles (Pd NPs) was well maintained after carbonization, which was attributed to the rigid structure of the 3D COF. Thanks to the uniform distribution of Pd NPs in the carbon, the catalyst exhibited a remarkable half-wave potential of 0.906 V and a Tafel slope of 70 mV dec-1 in 0.1 M KOH, surpassing the commercial Pt/C catalyst (0.863 V and 75 mV dec-1 ). Furthermore, a maximum power density of 144.0 mW cm-2 was achieved at 252 mA cm-2 , which was significantly higher than the control battery (105.1 mW cm-2 ). This work not only provides a simple strategy for in-situ preparation of highly dispersible metal catalysts in COFs, but also offers new insights into the ORR electrocatalysis.

CoNi Alloys Encapsulated in N-Doped Carbon Nanotubes for Stabilizing Oxygen Electrocatalysis in Zinc-Air Battery

Alloy-based catalysts with high corrosion resistance and less self-aggregation are essential for oxygen reduction/evolution reactions (ORR/OER). Here, via an in situ growth strategy, NiCo alloy-inserted nitrogen-doped carbon nanotubes were assembled on a three-dimensional hollow nanosphere (NiCo@NCNTs/HN) using dicyandiamide. NiCo@NCNTs/HN exhibited better ORR activity (half-wave potential (E_1/2) of 0.87 V) and stability (E_1/2 shift of only -13 mV after 5000 cycles) than commercial Pt/C. NiCo@NCNTs/HN displayed a lower OER overpotential (330 mV) than RuO₂ (390 mV). The NiCo@NCNTs/HN-assembled zinc-air battery exhibited high specific-capacity (847.01 mA h g^-1) and cycling-stability (291 h). Synergies between NiCo alloys and NCNTs facilitated the charge transfer to promote 4e^- ORR/OER kinetics. The carbon skeleton inhibited the corrosion of NiCo alloys from surface to subsurface, while inner cavities of CNTs confined particle growth and the aggregation of NiCo alloys to stabilize bifunctional activity. This provides a viable strategy for the design of alloy-based catalysts with confined grain-size and good structural/catalytic stabilities in oxygen electrocatalysis.

Construction of N-Doped Carbon-Modified Ni/SiO2 Catalyst Promoting Cinnamaldehyde Selective Hydrogenation

At present, the selective hydrogenation of α, β-unsaturated aldehydes remains a challenge due to competition between unsaturated functional groups (C=C and C=O). In this study, N-doped carbon deposited on silica-supported nickel Mott-Schottky type catalysts (Ni/SiO₂@N_xC) was prepared for the selective hydrogenation of cinnamaldehyde (CAL) by using the respective hydrothermal method and high-temperature carbonization method. The prepared optimal Ni/SiO₂@N₇C catalyst achieved 98.9% conversion and 83.1% selectivity for 3-phenylpropionaldehyde (HCAL) in the selective hydrogenation reaction of CAL. By constructing the Mott-Schottky effect, the electron transfer from metallic Ni to N-doped carbon at their contact interface was promoted, and the electron transfer was demonstrated by XPS and UPS. Experimental results indicated that by modulating the electron density of metallic Ni, the catalytic hydrogenation of C=C bonds was preferentially performed to obtain higher HCAL selectivity. Meanwhile, this work also provides an effective way to design electronically adjustable type catalysts for more selective hydrogenation reactions.

1,2,4-triazole-assisted metal-organic framework-derived nitrogen-doped carbon nanotubes with encapsulated Co4N particles as bifunctional oxygen electrocatalysts for rechargeable zinc-air batteries

The design of high-performance oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) dual-functional catalysts is not only important for the further applications of zinc-air batteries (ZABs) but also a major challenge in the field of energy conversion. The cheap 1,2,4-triazole (1,2,4-TZ) can be decomposed easily by heat, making it a high research value in carbon catalysts derived from metal-organic frameworks (MOFs). Here, Co₄N particles encapsulated at the top of N-doped carbon nanotubes (Co₄N@NCNTs) were conveniently prepared by 1,2,4-TZ-assisted pyrolysis of Co-MOF-74 for the first time. Owing to the excellent activity of Co₄N particles and the highly graphitized N-doped carbon nanotubes (NCNTs), Co₄N@NCNTs obtained at 900 °C (Co₄N@NCNT-900) exhibited astonishing catalytic performance in both ORR and OER, and high reversible oxygen bifunctional activity (ΔE = 0.685 V). Moreover, Co₄N@NCNT-900 displayed a larger discharge power density (122 mW cm^-2), a better specific capacity (811.8 mAh g^-1), and more excellent durability during the ZAB test, implying that Co₄N@NCNT-900 can act as a bifunctional high active catalyst in ZABs.

Directed electron regulation promoted sandwich-like CoO@FeBTC/NF with p-n heterojunctions by gel electrodeposition for oxygen evolution reaction

Metal organic framework (MOF) is currently-one of the key catalysts for oxygen evolution reaction (OER), but its catalytic performance is severely limited by electronic configuration. In this study, cobalt oxide (CoO) on nickel foam (NF) was first prepared, which then wrapped it with FeBTC synthesized by ligating isophthalic acid (BTC) with iron ions by electrodeposition to obtain CoO@FeBTC/NF p-n heterojunction structure. The catalyst requires only 255 mV overpotential to reach a current density of 100 mA cm^-2, and can maintain 100 h long time stability at 500 mA cm^-2 high current density. The catalytic properties are mainly related to the strong induced modulation of electrons in FeBTC by holes in the p-type CoO, which results in stronger bonding and faster electron transfer between FeBTC and hydroxide. At the same time, the uncoordinated BTC at the solid-liquid interface ionizes acidic radicals which form hydrogen bonds with the hydroxyl radicals in solution, capturing them onto the catalyst surface for the catalytic reaction. In addition, CoO@FeBTC/NF also has strong application prospects in alkaline electrolyzers, which only needs 1.78 V to reach a current density of 1 A cm^-2, and it can maintain long-term stability for 12 h at this current. This study provides a new convenient and efficient approach for the control design of the electronic structure of MOF, leading to a more efficient electrocatalytic process.

Dopant-Induced Surface Self-Etching of Cobalt Carbonate Hydroxide Boosts Efficient Water Splitting

Herein, vanadium-doped cobalt carbonate hydroxide, V-CoCH, was synthesized as efficient catalyst for water splitting. Vanadium species were partially dissolved in the early stages of the oxygen-evolution reaction (OER), inducing self-etching of the catalyst surface, which is helpful for catalyst surface reconstruction and resulted in a higher number of active sites and oxygen vacancies. The synergy between V-doping and oxygen vacancies improved the catalytic activity: V-CoCH showed an exceptional OER catalytic performance with an overpotential of 183 mV at 10 mA cm^-2 . The water-splitting cell consisting of V-CoCH only required 1.52 V to reach 10 mA cm^-2 . Theoretical calculations revealed that vanadium in V-CoCH played an important role in electron regulation of active sites. The oxygen vacancies had an important effect on improvement of the OER performance through not only the exposure of more active sites but also through modulation of the electronic structure. This work provides an effective strategy for constructing high-performance electrocatalysts.

Agarose-gel-based self-limiting synthesis of a bimetal (Fe and Co)-doped composite as a bifunctional catalyst for a zinc-air battery

Exploring efficient noble-metal-free electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) is crucial for the development of rechargeable Zn-air batteries. Herein, a self-limiting method using an agarose gel was proposed to prepare bimetallic (iron and cobalt) nitrogen-doped carbon composites (FeCo-NC). The resulting FeCo-NC catalyst has a high surface area and a hierarchical porous structure. The optimized FeCo-NC electrocatalyst exhibits a small potential difference (ΔE) = 0.72 V between the ORR half-wave potential and the OER potential at a current density of 10 mA cm^-2 in alkaline media. Impressively, the FeCo-NC Zn-air battery exhibits a high open-circuit voltage, large power density, and outstanding charge-discharge cycling stability. This study provides an effective means of designing electrocatalysts and energy conversion systems.

Highly Efficient Electrochemical Sensing of Acetaminophen by Cobalt Oxide-Embedded Nitrogen-Doped Hollow Carbon Spheres

With respect to sensor application investigations, hollow mesoporous carbon sphere-based materials of the spinel type of cobalt oxide (Co₃O₄) and heteroatom-doped materials are gaining popularity. In this contribution, dopamine hydrochloride (DA) and cobalt phthalocyanine (CoPc) precursors were employed to construct a highly homogeneous Co₃O₄-embedded N-doped hollow carbon sphere (Co₃O₄@NHCS) by a straightforward one-step polymerization procedure. The resulting Co₃O₄@NHCS materials may effectively tune the surface area, defect sites, and doping amount of N and Co elements by altering the loading amount of CoPc. The relatively high surface area, greater spherical wall thickness, enriched defect sites, and better extent of N and Co sites are all visible in the best 200 mg loaded Co₃O₄@NHCS-2 material. This leads to significant improvement in pyridine and graphitic N site concentrations, which offers exceptional electrochemical performance. Electrochemical analysis was used to study the electrocatalytic activity of Co₃O₄@NHCSs towards the sensing of pharmacologically active significant compounds (acetaminophen). Excellent sensor properties include the linear range (0.001-0.2 and 1.0-8.0 mM), sensitivity, limit of detection (0.07 and 0.11 μM), and selectivity in the modified Co₃O₄@NHCSs/GCE. The authentic sample (acetaminophen tablet) produces a satisfactory result when used practically.