In Situ Fabrication of Highly Dispersed Co-Fe-Doped-δ-MnO2 Catalyst by a Facile Redox-Driving MOFs-Derived Method for Low-Temperature Oxidation of Toluene

Ti3+/Ti4+ and Co2+/Co3+ redox couples in Ce-doped Co-Ce/TiO2 for enhancing photothermocatalytic toluene oxidation

Cerium and cobalt loaded Co-Ce/TiO2 catalyst prepared by impregnation method was investigated for photothermal catalytic toluene oxidation. Based on catalyst characterizations (XPS, EPR and H2-TPR), redox cycle between Co and TiO2 (Co2+ + Ti4+ ↔ Co3+ + Ti3+) results in the formation of Co3+, Ti3+ and oxygen vacancies, which play important roles in toluene catalytic oxidation reaction. The introduction of Ce brings in the dual redox cycles (Co2+ + Ti4+ ↔ Co3+ + Ti3+, Co2+ + Ce4+ ↔ Co3+ + Ce3+), further promoting the elevation of reaction sites amount. Under full spectrum irradiation with light intensity of 580 mW/cm2, Co-Ce/TiO2 catalyst achieved 96% of toluene conversion and 73% of CO2 yield, obviously higher than Co/P25 and Co/TiO2. Co-Ce/TiO2 efficiently maintains 10-hour stability test under water vapor conditions and exhibits better photothermal catalytic performance than counterparts under different wavelengths illumination. Photothermal catalytic reaction displays improved activities compared with thermal catalysis, which is attributed to the promotional effect of light including photocatalysis and light activation of reactive oxygen species.

Synthesis and Optimization of Foam Copper-Based CoMnOx@Co3O4/CF Catalyst: Achieving Efficient Catalytic Oxidation of Paraxylene

This study successfully developed a foam copper (CF)-based CoMnOx@Co3O4/CF composite catalyst, achieving efficient thermal catalytic oxidation of paraxylene through multifactor optimization of synthesis conditions. At a Co:Mn molar ratio of 2:1 and a calcination temperature of 450 °C, the catalyst exhibited outstanding catalytic performance, with a T90 temperature as low as 246 °C, significantly lower than that of catalysts synthesized under other conditions. Additionally, BET, XPS, Raman, EPR, and H2-TPR test results indicate that the catalyst possesses a high specific surface area, abundant oxygen vacancies, a distribution of multivalent Co and Mn species, and a lower hydrogen reduction temperature, all of which contribute to the high catalytic activity of CoMnOx@Co3O4/CF. Furthermore, in situ DRIFTS confirmed that the oxidation of paraxylene on CoMnOx@Co3O4/CF follows the Mars-Van Krevelen (MvK) mechanism. The proposed reaction pathway begins with the oxidation of the methyl group on paraxylene, followed by the opening of the benzene ring and further oxidation to CO2 and H2O. The innovative structural design and excellent catalytic performance of this catalyst provide new insights and solutions for the industrial treatment of VOCs.

Revealing the intrinsic nature of Cu- and Ce-doped Mn3O4 catalysts with positive and negative effects on CO oxidation using operando DRIFTS-MS

Aiming at the problem of the poor performance of an Mn-MOF-74-derived Mn3O4 catalyst in low-temperature carbon monoxide (CO) oxidation, copper (Cu) and cerium (Ce) elements were used to modify the Mn3O4 catalyst to improve its performance in low-temperature CO oxidation. According to the results of catalytic performance testing, the CO oxidation activity of the Cu0.3Mn2.7O4 catalyst was significantly improved compared with that of the pristine Mn3O4 catalyst, when a CO conversion rate of 90% was achieved at 118 °C. According to X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller analyses, the (Mn2+ + Mn3+)/(Mn2+ + Mn3+ + Mn4+) ratio and the Oads/Ototal ratio increased after Cu doping, indicating promoted oxygen vacancy generation. In addition, the increased specific surface area was beneficial for the adsorption of reactant molecules and the exposure of active sites. According to H2-temperature-programmed reduction characterization, Cu doping significantly enhanced the performance of the Cu0.3Mn2.7O4 catalyst during low-temperature redox. Finally, these factors synergistically promoted the degradation of CO over the Cu0.3Mn2.7O4 catalyst. In addition, operando diffuse reflectance Fourier transform infrared spectroscopy results suggested the presence of more terminal-type oxygen, which is essential for the catalytic oxidation of CO on the surface of the Cu0.3Mn2.7O4 catalyst. Moreover, the Cu0.3Mn2.7O4 catalyst also showed excellent resistance to carbonate, and remarkable stability.

Cathode|Electrolyte Interface Engineering by a Hydrogel Polymer Electrolyte for a 3D Porous High-Voltage Cathode Material in a Quasi-Solid-State Zinc Metal Battery by In Situ Polymerization

This work highlights the development of a superior cathode|electrolyte interface for the quasi solid-state rechargeable zinc metal battery (QSS-RZMB) by a novel hydrogel polymer electrolyte using an ultraviolet (UV) light-assisted in situ polymerization strategy. By integrating the cathode with a thin layer of the hydrogel polymer electrolyte, this technique produces an integrated interface that ensures quick Zn2+ ion conduction. The coexistence of nanowires for direct electron routes and the enhanced electrolyte ion infiltration and diffusion by the 3D porous flower structure with a wide open surface of the Zn-MnO electrode complements the interface formation during the in situ polymerization process. The QSS-RZMB configured with an integrated cathode (i-Zn-MnO) and the hydrogel polymer electrolyte (PHPZ-30) as the separator yields a comparable specific energy density of 214.14 Wh kg-1 with that of its liquid counterpart (240.38 Wh kg-1, 0.5 M Zn(CF3SO3)2 aqueous electrolyte). Other noteworthy features of the presented QSS-RZMB system include its superior cycle life of over 1000 charge-discharge cycles and 85% capacity retention with 99% coulombic efficiency at the current density of 1.0 A g-1, compared to only 60% capacity retention over 500 charge-discharge cycles displayed by the liquid-state system under the same operating conditions.

Constructing Active Cu2+-O-Fe3+ Sites at the CuO-Fe3O4 Interface to Promote Activation of Surface Lattice Oxygen

Activating surface lattice oxygen (Olatt) through the modulation of metal-oxygen bond strength has proven to be an effective route for facilitating the catalytic degradation of volatile organic compounds (VOCs). Although this strategy has been implemented via the construction of the TM1-O-TM2 (TM represents a transition metal) structure in various reactions, the underlying principle requires exploration when using different TMs. Herein, the Cu2+-O-Fe3+ structure was created by developing CuO-Fe3O4 composites with enhanced interfacial effect, which exhibited superior catalytic activity to their counterparts, with T90 (the temperature of toluene conversion reaching 90%) decreasing by approximately 50 °C. Structural analyses and theoretical calculations demonstrated that the active Cu2+-O-Fe3+ sites at the CuO-Fe3O4 interface improved low-temperature reducibility and oxygen species activity. Particularly, X-ray absorption fine structure spectroscopy revealed the contraction and expansion of Cu-O and Fe-O bonds, respectively, which were responsible for the activation of the surface Olatt. A mechanistic study revealed that toluene can be oxidized by rapid dehydrogenation of methyl assisted by the highly active surface Olatt and subsequently undergo ring-opening and deep mineralization into CO2 following the Mars-van Krevelen mechanism. This study provided a novel strategy to explore interface-enhanced TM catalysts for efficient surface Olatt activation and VOCs abatement.

Redox-Induced In Situ Growth of MnO2 with Rich Oxygen Vacancies over Monolithic Copper Foam for Boosting Toluene Combustion

Catalytic combustion has been known to be an effective technique in volatile organic compound (VOC) abatement. Developing monolithic catalysts with high activity at low temperatures is vital yet challenging in industrial applications. Herein, monolithic MnO₂-O_v/CF catalysts were fabricated via the in situ growth of K₂CuFe(CN)₆ (CuFePBA, a family of metal-organic frames) over copper foam (CF) followed by a redox-etching route. The as-synthesized monolith MnO₂-O_v-0.04/CF catalyst displays a superior low-temperature activity (T_90% = 215 °C) and robust durability for toluene elimination even in the presence of 5 vol % water. Experimental results reveal that the CuFePBA template not only guides the in situ growth of δ-MnO₂ with high loading over CF but also acts as a source of dopant to create more oxygen vacancies and weaken the strength of the Mn-O bond, which considerably improves the oxygen activation ability of δ-MnO₂ and consequently boosts the low-temperature catalytic activity of the monolith MnO₂-O_v-0.04/CF toward toluene oxidation. In addition, the reaction intermediate and proposed mechanism in the MnO₂-O_v-0.04/CF mediated catalytic oxidation process were investigated. This study provides new insights into the development of highly active monolithic catalysts for the low-temperature oxidation of VOCs.

Expediting Toluene Combustion by Harmonizing the Ce-O Strength over Co-Doped CeZr Oxide Catalysts

Low-temperature catalytic degradation of volatile organic compounds (VOCs) by enhancing the activity of non-precious metal catalysts has always been the focus of attention. The mineralization of aromatic VOCs requires the participation of a large number of oxygen atoms, so the activation of oxygen species is crucial in the degradation reaction. Herein, we originally adjust the Ce-O bond strength in CeZr oxide catalysts by cobalt doping to promote the activation of oxygen species, thus improving the toluene degradation performance while maintaining high stability. Subsequent characterizations and theoretical calculations demonstrate that the weakening of the Ce-O bond strength increases the oxygen vacancy content, promotes the activation of oxygen species, and enhances the redox ability of the catalysts. This strategy also promotes the activation of toluene and accelerates the depletion of intermediate species. This study will contribute a strategy to enhance the activation ability of oxygen species in non-noble metal oxide catalysts, thereby enhancing the degradation performance of VOCs.