Synchronously Achieving Plasmonic Bi Metal Deposition and I(-) Doping by Utilizing BiOIO3 as the Self-Sacrificing Template for High-Performance Multifunctional Applications

Self-powered photoelectrochemical aptasensor based on hollow tubular g-C3N4/Bi/BiVO4 for tobramycin detection

A highly sensitive photoelectrochemical aptasensor based on phosphorus-doped hollow tubular g-C₃N₄/Bi/BiVO₄ (PT-C₃N₄/Bi/BiVO₄) for tobramycin (TOB) detecting was developed. This aptasensor is a self-powered sensing system which could generate the electrical output under visible light irradiation with no external voltage supply. Based on the surface plasmon resonance (SPR) effect and unique hollow tubular structure of PT-C₃N₄/Bi/BiVO₄, the PEC aptasensor exhibited an enhanced photocurrent and favorably specific response to TOB. Under the optimized conditions, the sensitive aptasensor presented a wider linearity to TOB in the range of 0.01-50 ng mL^-1 with a low detection limit of 4.27 pg mL^-1. This sensor also displayed a satisfying photoelectrochemical performance with optimistic selectivity and stability. In addition, the proposed aptasensor was successfully applied to the detection of TOB in river water and milk samples.

BiOIO3@Zn3(PO4)2·4H2O Heterojunction with Fast Ionic Diffusion Kinetics for Long-Life "Rocking-Chair" Zinc Ion Batteries

Increasing insertion host materials are developed as high-performance anodes of "rocking-chair" zinc ion batteries. However, most of them show unsatisfactory rate capabilities. Herein, layered BiOIO₃ is reported as an excellent insertion host and a zinc ion conductor, i.e., Zn₃(PO₄)₂·4H₂O (ZPO), is introduced to construct a BiOIO₃@ZPO heterojunction with a built-in electric field (BEF). Both ZPO and a BEF obviously enhance Zn²⁺ transfer and storage, which is proven by theoretical calculations and experimental studies. The conversion-type mechanism of BiOIO₃ is revealed through ex situ characterizations. The optimized electrode exhibits a high reversible capacity of 130 mAh g^-1 at 0.1 A g^-1, a low average discharge voltage of 0.58 V, an ultrahigh rate performance with 68 mAh g^-1 at 5 A g^-1 (52% of capacity at 0.1 A g^-1), and an ultralong cyclic life of 6000 cycles at 5 A g^-1. Significantly, the BiOIO₃@ZPO//Mn₃O₄ full cell shows a good cyclic life of 67 mAh g^-1 over 1000 cycles at 0.1 A g^-1. This work provides a new insight into the design of anodes with excellent rate capability.

Typical layered structure bismuth-based photocatalysts for photocatalytic nitrogen oxides oxidation

Traditional NO_x treatment methods require external reducing reagents and harsh reaction conditions, which is not conducive to effectively eliminate NO_x at low concentration, especially at ppb levels. Fortunately, low concentration NO_x can be removed by photocatalytic oxidation under mild reaction conditions. Bismuth (Bi)-based photocatalysts with the layered structure have obtained considerable concerns of photocatalytic NO_x oxidation. This review focused on typical layered Bi-based photocatalysts (Bi₂WO₆, Bi₂O₂CO₃, BiOY (YCl, Br, and I), BiOIO₃, and BiOCOOH) with the structure of [Bi₂O₂]²⁺ layer for photocatalytic NO_x oxidation. The strategies (morphological control, defect engineering, heterostructure construction, etc.) to improve photocatalytic oxidation activity were summarized. Furthermore, the mechanism involving various free radicals (hydroxyl radical, superoxide radical, etc.) of photocatalytic oxidation of NO_x was proposed. In addition, the non-NO₂ selectivity was also illuminated. Lastly, the current drawbacks and further research directions for photocatalytic NO_x oxidation were elaborated. The development of photocatalysts with high photocatalytic activity, wide light absorption range, and non-NO₂ selectivity is the focus of future research. This review aims to provide a pandect and theoretical guidance for the practical application of photocatalytic oxidation of NO_x.

Non-Noble Plasmonic Metal-Based Photocatalysts

Solar-to-chemical energy conversion via heterogeneous photocatalysis is one of the sustainable approaches to tackle the growing environmental and energy challenges. Among various promising photocatalytic materials, plasmonic-driven photocatalysts feature prominent solar-driven surface plasmon resonance (SPR). Non-noble plasmonic metals (NNPMs)-based photocatalysts have been identified as a unique alternative to noble metal-based ones due to their advantages like earth-abundance, cost-effectiveness, and large-scale application capability. This review comprehensively summarizes the most recent advances in the synthesis, characterization, and properties of NNPMs-based photocatalysts. After introducing the fundamental principles of SPR, the attributes and functionalities of NNPMs in governing surface/interfacial photocatalytic processes are presented. Next, the utilization of NNPMs-based photocatalytic materials for the removal of pollutants, water splitting, CO₂ reduction, and organic transformations is discussed. The review concludes with current challenges and perspectives in advancing the NNPMs-based photocatalysts, which are timely and important to plasmon-based photocatalysis, a truly interdisciplinary field across materials science, chemistry, and physics.

Facile one-step strategy for the formation of BiOIO3/[Bi6O6(OH)3](NO3)3·1.5H2O heterojunction to enhancing photocatalytic activity

The heterojunction photocatalyst, BiOIO₃/[Bi₆O₆(OH)₃](NO₃)₃·1.5H₂O (BiOIO₃/BBN), was successfully synthesized by a simple one-step hydrothermal method. The results showed that under UV light irradiation, the formation of a heterojunction could greatly enhance the photocatalytic efficiency of the prepared catalyst for bisphenol A (BPA). The BiOIO₃/BBN heterostructure had the best reaction rate constant, which was 81.82 times, 1.52 times, and 43.40 times improvement of TiO₂, BiOIO₃, and BBN respectively. Through the free radical capture experiments and electron spin resonance spectroscopy, it was conducted that ¹O₂, h⁺, e^-, •OH and •O₂^- were reactive species in the process of photocatalytic degradation of BPA. The photocatalytic mechanism was further investigated and confirmed that the BiOIO₃/BBN heterojunction could improve the separation and transfer of photo-generated carriers, thereby greatly enhancing the catalytic efficiency. The degradation products of BPA were detected by HPLC-MS, and the degradation reaction pathway was deduced.

Recent Progress on Metal-Enhanced Photocatalysis: A Review on the Mechanism

Metal-enhanced photocatalysis has recently received increasing interest, mainly due to the ability of metal to directly or indirectly degrade pollutants. In this review, we briefly review the recent breakthroughs in metal-enhanced photocatalysis. We discussed the recent progress of surface plasmon resonance (SPR) effect and small size effect of metal nanoparticles on photocatalysis; in particular, we focus on elucidating the mechanism of energy transfer and hot electron injection/transfer effect of metal nanoparticles and clusters while as photocatalysts or as cophotocatalysts. Finally, we discuss the potential applications of metal-enhanced photocatalysis, and we also offer some perspectives for further investigations.

Boosting photoresposive ability of WO3-Bi2O3nanocomposite rods via annealing-induced intrinsic precipitation of nanosized Bi particles

In this study, Bi-particle-functionalized tungsten trioxide-bismuth oxide (WO₃-Bi₂O₃) composite nanorods were prepared by integrating sputtering and hydrothermal syntheses with an appropriate postannealing procedure to induce Bi particle precipitation. Unlike other routes in which metal particle decoration is achieved externally, in this study, photoresponsive one-dimensional WO₃-Bi₂O₃composite nanorods were decorated with Bi particles by using the internal precipitation method. Structural analysis revealed that the Bi-metal-particle-functionalized WO₃-Bi₂O₃composite nanorods with particle size ranging from 5 to 10 nm were formed through hydrogen gas annealing at an optimal annealing temperature of 350 °C. Compared with the pristine WO₃nanorod template, the Bi-WO₃-Bi₂O₃composite nanorods exhibited higher photoresponsive performance, substantial photogenerated charge transfer ability, and efficient separation of photogenerated electron-hole pairs. The study results indicated that the Bi-WO₃-Bi₂O₃composite nanorods had superior decontamination ability and excellent stability toward RhB dye as compared with pristine WO₃. Moreover, the photogenerated charge separation and migration efficiencies of the WO₃-Bi₂O₃nanorods could be tuned through appropriate reduction of the surface oxide layer; this is a promising approach to designing WO₃-Bi₂O₃nanorods with high photoactive performance.

Bi metal/oxygen-deficient BiO2-x with tetrahedral morphology and high photocatalytic activity

Vacancy-rich materials with high photocatalytic activity are of great interest for pollutants removal and play a significant role in green chemistry. Herein, we successfully synthesized Bi/BiO_2-x composite through hydrothermal route. In this case, the surface plasmon resonance effect of Bi and oxygen vacancies of BiO_2-x collectively increase the removal rate of pollutants. More importantly, the Bi/BiO_2-x composites have enhanced activity in the degradation of RhB, MO, BPA and CIP, and the reduction of Cr(VI) and PNA. Besides, an enhanced photocatalytic activity is due to the main reactive species of ·[Formula: see text] and h⁺ that is confirmed by trapping experiments and ESR analyses. The electronic structure and visible light harvesting of photocatalysts were measured and also theoretically calculated by using density functional theory and finite difference time domain calculations, DRS, VB x-ray photoelectron spectroscopy and Mott-Schottky plots, which allowed to propose a possible photocatalytic mechanism for the degradation process.

Refining the band structure of BiOBr nanosheets through the synergetic effect of VO43− ions replacement and oxygen vacancies for promoted visible-light-driven photocatalysis

The band structure of BiOBr nanosheets is regulated by the oxygen vacancies and VO₄³⁻ ions replacement. The BiOBr nanosheets possess defective states and a more negative conduction band potential, promoting visible-light photocatalytic activity.

Recent Progress on Metal-Enhanced Photocatalysis: A Review on the Mechanism

Metal-enhanced photocatalysis has recently received increasing interest, mainly due to the ability of metal to directly or indirectly degrade pollutants. In this review, we briefly review the recent breakthroughs in metal-enhanced photocatalysis. We discussed the recent progress of surface plasmon resonance (SPR) effect and small size effect of metal nanoparticles on photocatalysis; in particular, we focus on elucidating the mechanism of energy transfer and hot electron injection/transfer effect of metal nanoparticles and clusters while as photocatalysts or as cophotocatalysts. Finally, we discuss the potential applications of metal-enhanced photocatalysis, and we also offer some perspectives for further investigations.

Flower-like Bi2SiO5/Bi4MoO9 heterostructures for enhanced photocatalytic degradation of ciprofloxacin

Bi₂SiO₅/Bi₄MoO₉ photocatalysts with heterostructures were successfully prepared using a one-pot solvothermal route. The effect of the molybdenum source on composite formation is discussed. Under ultraviolet light irradiation, the Bi₂SiO₅/Bi₄MoO₉ heterojunction photocatalyst exhibited higher photocatalytic performance than Bi₂SiO₅ and Bi₄MoO₉ towards the degradation of ciprofloxacin (CIP). This dramatically enhanced photoactivity can be ascribed to the construction of a heterojunction interface between Bi₂SiO₅ and Bi₄MoO₉, which not only suppresses the recombination of photoexcited charge carriers but also enhances light absorption. In addition, from a practical point of view, the the effect of initial CIP concentration and coexisting ions on the photodegradation process using as-prepared Bi₂SiO₅/Bi₄MoO₉ heterojunction photocatalysts was explored. Trapping experiments demonstrate that photoexcited holes and superoxide radicals are the main active species in the photodegradation of CIP over Bi₂SiO₅/Bi₄MoO₉ heterojunctions. Meanwhile, the conduction band and valence band potentials of Bi₂SiO₅ and Bi₄MoO₉ were measured by density functional theory calculation, diffuse reflectance spectroscopy and Mott-Schottky curves. A possible photocatalytic mechanism for CIP degradation over the Bi₂SiO₅/Bi₄MoO₉ heterojunction is proposed.

Ternary Z-scheme heterojunction of Bi SPR-promoted BiVO4/g-C3N4 with effectively boosted photoelectrochemical activity for constructing oxytetracycline aptasensor

Developing photoactive materials with wide spectral response is critical to improve the sensitivity of PEC biosensors. Herein, a sensitive photoelectrochemical (PEC) aptasensor was fabricated based on Bi surface plasmon resonance (SPR)-promoted BiVO₄/g-C₃N₄ (Bi/BiVO₄/g-C₃N₄) as photoactive material for the detection of oxytetracycline (OTC). Ternary Z-scheme Bi/BiVO₄/g-C₃N₄ heterojunction exhibited widest spectral response and best PEC activity compared to g-C₃N₄, BiVO₄, Bi/BiVO₄, and BiVO₄/g-C₃N₄. The wide spectral response and high PEC activity could be attributed to three reasons: Firstly, the SPR effect of Bi could greatly increase light harvesting; Secondly, Bi served as an electron conduction bridge between BiVO₄ and g-C₃N₄ to form Z-scheme structure, significantly accelerating the separation of photogenerated carriers; Thirdly, the synergism of Z-scheme heterojunction and the SPR effect of Bi efficiently boosted the photoelectric response. Based on the above sensitization strategies, the proposed PEC aptasensor for OTC determination showed a wide linear range of 0.01-1000 nM and a low detection limit (S/N = 3) of 3.3 × 10^-3 nM. Moreover, the high stability, satisfactory repeatability and favorable practicability of the fabricated PEC aptasensor revealed the potential applications for accurate monitoring of antibiotics in environmental media.

Recent Advances and Applications of Semiconductor Photocatalytic Technology

Along with the development of industry and the improvement of people’s living standards, peoples’ demand on resources has greatly increased, causing energy crises and environmental pollution. In recent years, photocatalytic technology has shown great potential as a low-cost, environmentally-friendly, and sustainable technology, and it has become a hot research topic. However, current photocatalytic technology cannot meet industrial requirements. The biggest challenge in the industrialization of photocatalyst technology is the development of an ideal photocatalyst, which should possess four features, including a high photocatalytic efficiency, a large specific surface area, a full utilization of sunlight, and recyclability. In this review, starting from the photocatalytic reaction mechanism and the preparation of the photocatalyst, we review the classification of current photocatalysts and the methods for improving photocatalytic performance; we also further discuss the potential industrial usage of photocatalytic technology. This review also aims to provide basic and comprehensive information on the industrialization of photocatalysis technology.

Synthesis of α-Fe2O3/Bi2WO6 layered heterojunctions by in situ growth strategy with enhanced visible-light photocatalytic activity

Layered heterojunction structure with larger interface region for electron migration has attracted much attention in recent years. In this work, layered α-Fe₂O₃/Bi₂WO₆ heterojunctions with strong interlayer interaction were successfully synthesized through a facile in situ growth method. The strong interaction between α-Fe₂O₃ and Bi₂WO₆ had resulted in excellent photoelectrochemical performance. It was found that such structure promoted the interfacial photogenerated charges separation according to EIS and Tafel analysis, except for the expansion of visible-light absorption range. PL and TRPL characterizations further demonstrated that the recombination ratio of photoexcited electron-hole pairs was greatly reduced. The toluene photocatalytic degradation tests had showed that α-Fe₂O₃/Bi₂WO₆ composites exhibited much well activity under visible-light irradiation. Especially, 4%-Fe₂O₃/Bi₂WO₆ sample displayed the highest photocatalytic activity, which was around 3 and 4 times higher than that of pure Bi₂WO₆ and α-Fe₂O₃. Based on ESR results and free radical trapping experiments, hydroxyl radicals (·OH) and holes (h⁺) were regarded as the main active species. The establishment of Fe₂O₃/Bi₂WO₆ with layered heterojunctions could provide new insights into the construction of novel photocatalysts.

An in situ Bi-decorated BiOBr photocatalyst for synchronously treating multiple antibiotics in water

Currently, there is an urgent demand for developing new materials to remove antibiotics in the water environment, especially for the simultaneous degradation of multiple antibiotics. Here, we fabricated a novel Bi/BiOBr heterostructure via an in situ solvothermal strategy, and it exhibited excellent visible-light-responsive photocatalytic activity for synchronously removing multiple antibiotics coexisting in water. The Bi nanoparticles could extend the light absorption spectra of the sample and further facilitate electron-hole pair separation. The in-depth electron spin resonance (ESR) results confirm that the active species in Bi/BiOBr are holes (h⁺) and superoxide radicals (·O₂ ^-) under irradiation, and it is also proved that Bi could selectively reduce the formation of ·O₂ ^- in the BiOBr matrix. The coexisting system of TC (tetracycline hydrochloride), CIP (ciprofloxacin) and DOX (doxycycline) could be simultaneously photodegraded to approximately 0% within 30 min by the Bi/BiOBr photocatalyst.

One-Dimensional/Two-Dimensional Core-Shell-Structured Bi2O4/BiO2- x Heterojunction for Highly Efficient Broad Spectrum Light-Driven Photocatalysis: Faster Interfacial Charge Transfer and Enhanced Molecular Oxygen Activation Mechanism

Deliberate tuning of nanoparticles encapsulated with nanosheet shells can bring about fascinating photocatalytic properties because of the fast charge-transfer characteristics of a nanosized core-shell structure. Herein, a novel core-shell-structured Bi₂O₄/BiO_{2- x} composite was fabricated through a one-step hydrothermal method. The core-shell Bi₂O₄/BiO_{2- x} composite presented distinct optical absorption property, including UV, visible, and near-infrared (NIR) light regions. Compared to Bi₂O₄ and BiO_{2- x}, the Bi₂O₄/BiO_{2- x} composite revealed improved broad spectrum light-responsive molecular oxygen activation into ^•O₂^-, especially achieving ^•O₂^- generation under NIR light irradiation. The achievement that enhanced broad spectrum light-activated molecular oxygen activation could be ascribed to the faster electron transfer confirmed by the electron spin resonance (ESR) spectra, photoluminescence (PL) spectra, photoelectrochemical test, and quantitative analysis of ^•O₂^-. The strong interface effect of the Bi₂O₄/BiO_{2- x} composite was confirmed by X-ray photoelectron spectroscopy analysis. Density functional theory calculated results suggested that the Bi₂O₄/BiO_{2- x} composite revealed increased density of states near the Fermi level, suggesting that it possessed higher carrier mobility as compared to Bi₂O₄ and BiO_{2- x}, contributing to the faster separation of photoinduced carriers and the generation of ^•O₂^-. Benefiting to the heterojunction, the Bi₂O₄/BiO_{2- x} composite showed improved photocatalytic activity and anti-photocorrosion activity during rhodamine B (RhB) and ciprofloxacin (CIP) degradation with the irradiation of UV, visible, and NIR lights. Besides, the possible photocatalytic mechanism and transformation pathway of RhB and CIP degradation by the Bi₂O₄/BiO_{2- x} composite were proposed by the analyses of the liquid chromatography-mass spectrometry. This study furnishes a new strategy for fabricating high-efficient and broad spectrum light-driven heterojunction photocatalysts for environment purification.

Bismuth oxyiodide coupled with bismuth nanodots for enhanced photocatalytic bisphenol A degradation: synergistic effects and mechanistic insight

Bismuth based semiconductor photocatalysts are being generated as promising materials for photocatalysis. In this work, hydrothermal methods have been utilized to synthesize a bismuth oxyiodide semiconductor with deposited Bi nanodots (Bi-BiOI), which could create oxygen defects and accelerate photoinduced charge migration simultaneously. The resulting Bi-BiOI strongly demonstrates the high photocatalytic performance for bisphenol A and methylene blue degradation under visible light. 86% of BPA was degraded after an irradiation time of 4 hours. Electrospray ionization mass spectrometry was employed to detect the evolution of intermediates formed during the decomposition process of bisphenol A, and the following results suggested complete bisphenol A mineralization. Additionally, electron paramagnetic resonance results revealed the production of free radicals and the presence of oxygen vacancies. Furthermore, a distinctively increased photocurrent response and photoluminescence decay dynamics demonstrate that the interface between the Bi nanodots and BiOI semiconductor promotes the separation and migration of photoinduced electron-hole pairs. The lower valence band value (2.57 eV) of Bi-BiOI presented a higher oxidation potential, thus the production of hydroxyl radicals could be promoted considerably. Based on the experimental results, factors such as oxygen vacancies, effective charge migration, suppressed photoinduced electron-hole pair recombination and a high Bi-BiOI oxidation potential would result in advanced free radical production capacity, thereby enhancing the photocatalytic efficiency. The findings of our work will contribute to the fabrication of metal nanodot deposited semiconductor photocatalysts and pave the way for the utilization of advanced oxidation technology.

In-depth insight into facet-dependent charge movement behaviors and photo-redox catalysis: A case of {001} and {010} facets BiOCl

A central issue in understanding photo-redox catalysis is the facet-dependent charge movement behaviors that include bulk charge separation, surface charge transfer and interfacial charge migration. To get in-depth insight into these complicated processes steered by different exposing facets, herein BiOCl with exposed (001) and (010) facets engaged as the model are investigated. The BiOCl-(010) and BiOCl-(001) single-crystalline sheets are separately synthesized via hydrothermal and hydrolysis routes. In contrast to BiOCl-(010), BiOCl-(001) demonstrates highly promoted photo-redox performance for H₂ generation and degradation of pollutants. The facet-dependent charge movement behaviors were surveyed by surface photovoltage spectroscopy (SPV), transient photocurrent, linear sweep voltammetry, continuous wavelength photocurrent, and electrochemical impedance spectrum (EIS). All the photoelectrochemical and photoelectric measurement results reflect that BiOCl-(001) exhibits superior charge separation and migration efficiencies in the whole charge movement process than the BiOCl-(010). Besides, a higher charge carrier density (3.1-fold enhancement) was also observed for BiOCl-(001) compared to BiOCl-(010). Our current work is expected to further our understanding on facet-dependent charge movement behaviors and offer new insight into design of high-performance photocatalytic/photoelectrochemical materials.

In-Situ Hydrothermal Synthesis of Bi-Bi2O2CO3 Heterojunction Photocatalyst with Enhanced Visible Light Photocatalytic Activity

Bismuth containing nanomaterials recently received increasing attention with respect to environmental applications because of their low cost, high stability and nontoxicity. In this work, Bi-Bi₂O₂CO₃ heterojunctions were fabricated by in-situ decoration of Bi nanoparticles on Bi₂O₂CO₃ nanosheets via a simple hydrothermal synthesis approach. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) were used to confirm the morphology of the nanosheet-like heterostructure of the Bi-Bi₂O₂CO₃ composite. Detailed ultrafast electronic spectroscopy reveals that the in-situ decoration of Bi nanoparticles on Bi₂O₂CO₃ nanosheets exhibit a dramatically enhanced electron-hole pair separation rate, which results in an extraordinarily high photocatalytic activity for the degradation of a model organic dye, methylene blue (MB) under visible light illumination. Cycling experiments revealed a good photochemical stability of the Bi-Bi₂O₂CO₃ heterojunction under repeated irradiation. Photocurrent measurements further indicated that the heterojunction incredibly enhanced the charge generation and suppressed the charge recombination of photogenerated electron-hole pairs.

Defect Engineering of Bismuth Oxyiodide by IO3- Doping for Increasing Charge Transport in Photocatalysis

Defect engineering is regarded as one of the most active projects to monitor the chemical and physical properties of materials, which is expected to increase the photocatalytic activities of the materials. Herein, oxygen vacancies and IO₃^- doping are introduced into BiOI nanosheets via adding NaH₂PO₂, which can impact the charge carrier dynamics of BiOI photocatalysts, such as its excitation, separation, trap, and transfer. These oxygen-deficient BiOI nanosheets display attractive photocatalytic activities of gaseous formaldehyde degradation and methyl orange under visible light irradiation, which are 5 and 3.5 times higher than the BiOI samples, respectively. Moreover, the comodified BiOI also displayed superior cycling stability and can be used for practical application. This work not only develops an effective strategy for fabricating oxygen vacancies but also offers deep insight into the impact of surface defects in enhancing photocatalysis.

Photocatalytic activities of coke carbon/g-C3N4 and Bi metal/Bi mixed oxides/g-C3N4 nanohybrids for the degradation of pollutants in wastewater

Different g-C₃N₄ composite systems (coke carbon/g-C₃N₄, Bi/Bi₂WO₆/g-C₃N₄ and Bi/Bi₂MoO₆/g-C₃N₄) have been assessed as photocatalysts for wastewater pollutants removal. The coke carbon/g-C₃N₄ hybrid, produced by thermal treatment at 550 °C of a composite made from melamine cyanurate and coke, only showed activity under UV-light irradiation. On the other hand, inorganic Bi spheres/Bi mixed oxides/g-C₃N₄ nanohybrids (Bi/Bi₂WO₆/g-C₃N₄ and Bi/Bi₂MoO₆/g-C₃N₄ composites), produced by thermal reduction of Bi₂WO₆ or Bi₂MoO₆ by g-C₃N₄, exhibited a remarkable red-shift, up to 620 nm, and allowed the visible-light driven degradation of the contaminant, albeit in combination with some adsorption.

Interlayer-I-doped BiOIO3 nanoplates with an optimized electronic structure for efficient visible light photocatalysis

I-intercalated BiOIO₃ demonstrated outstanding NO removal ability due to its extended light response, enhanced oxidation capability and improved carrier separation endowed by the interbedded I atoms.

Facile fabrication of BiOIO3/BiOBr composites with enhanced visible light photocatalytic activity

BiOIO₃/BiOBr composite photocatalysts were successfully fabricated through a hydrothermal and subsequent chemical precipitation method.