Synthesis and Characterization of Alkylamine-Functionalized Si(111) for Perovskite Adhesion With Minimal Interfacial Oxidation or Electronic Defects

Waste-to-wealth application of wastewater treatment algae-derived hydrochar for Pb(II) adsorption

Hydrochar, as an energy-lean solid waste, is generated from an advanced biofuel conversion technique hydrothermal liquefaction (HTL) and always leads to environmental pollution without appropriate disposal. In this study, HTL-derived hydrochar is recycled and prepared as adsorbent used for Pb(Ⅱ) removal from wastewater. As the original porous structure of hydrochar is masked by oily volatiles remained after HTL, two types of oil-removal pretreatment (Soxhlet extraction and CO₂ activation) are explored. The result shows that CO₂ activation significantly enhances the adsorption capacity of Pb(Ⅱ), and the maximum adsorption capacity is 12.88 mg g⁻¹, as evaluated using Langmuir adsorption model. Further, apart from oily volatiles, most inorganic compounds derived from wastewater-grown algae is enriched in hydrochar, causing a smaller surface area of hydrochar. An ash-removal alkali treatment following CO₂ activation is introduced to dramatically increase the adsorption capacity to 25.00 mg g⁻¹ with an extremely low Pb(II) equilibrium concentration of 5.1×10^-4 mg L⁻¹, which is much lower than the maximum level of Pb concentration in drinking water (set by World Health Organization). This work introduces an approach to reuse HTL-hydrochar as an inexpensive adsorbent in Pb-contaminated water treatment, which not only provides another possible renewable adsorbent candidate applied in the field of lead adsorption, but also finds an alternative route to reduce solid waste effluent from HTL process.

Quantification of Surface Reactivity and Step-Selective Etching Chemistry on Single-Crystal BiOI(001)

To bridge the gap between the cleanliness of a freshly cleaved surface of 2D BiOI and that available from a purely chemical-etching means, we subjected single-crystal BiOI to a series of surface treatments and quantified the resulting chemical states and electronic properties. Vapor transport syntheses included both physical vapor transport from single-source BiOI, as well as chemical vapor transport from Bi₂O₃ + BiI₃ and from Bi + I₂ + Bi₂O₃. Surface treatments included tape cleaving, rinsing in water, sonication in acetone, an aqueous HF etch, and a sequential HF etch with subsequent sonication in acetone. X-ray diffraction, XRD, and X-ray photoelectron spectroscopy, XPS, probed the resulting bulk crystalline species and interfacial chemical states, respectively. In comparison with overlayer models of idealized oxide-terminated or iodide-terminated BiOI, angle-resolved XPS elucidated surface terminations as a function of each treatment. Ultraviolet photoelectron spectroscopy, UPS, established work-function, and Fermi-level energies for each treatment. Data reveal that HF etching yields interfacial BiI₃ at BiOI steps that is subsequently removed with acetone sonication. UPS establishes n-type behavior for the vapor-transport-synthesized BiOI, and surface work function and Fermi level shifts for each chemical treatment under study. We discuss the implications for processing BiOI nanofilms for energy-conversion applications.

Open-Circuit Photovoltage Exceeding 950 mV with an 840 mV Average at Sb2S3-Thianthrene+/0 Junctions Enabled by Thioperylene Anhydride Back Contacts

Covalently attached perylene monolayers serve as back contacts for Sb2S3 photoelectrochemical cells with a thianthrene+/0 front, rectifying contact. Covalent attachment of perylenetetracarboxylic dianhydride, PTCDA, to Si(111) utilizes an anhydride-to-imide conversion at surface-attached amines. For Sb2S3 solar absorbers, we hypothesized that a terminal thioperylene anhydride, i.e., S=C-O-C=S, formed from thionation of the terminal perylene anhydride would serve as a soft, electron-selective and hole-blocking back contact. We explored several routes to convert carbonyls to thiocarbonyls on surface-attached perylene anhydrides including Lawesson's reagent, P4S10, and a P4S10-pyridine complex. Here, P4S10 in toluene yielded the highest conversion as quantified by thioperylene-anhydride-S-to-imide-N ratios in X-ray photoelectron spectroscopy (XPS). Spectra demonstrated minimal residual reagent as determined by the absence of quantifiable phosphorus following sonication and rinsing. Photoelectrochemistry yielded an average |V oc| = 840 ± 90 mV with the highest value of 952 mV under ELH-simulated AM1.5G illumination for chemical-bath-deposited Sb2S3 in the strongly oxidizing thianthrene+/0 redox couple when thioperylene-anhydride-tethered surfaces formed the back contact. Sb2S3 absorbers in which perylene anhydride, esters, thionoesters, and thiols form the back contact yielded significantly decreased |V oc| magnitudes vs Sb2S3 on perylene-thioanhydride-terminated surfaces. We attribute the large V oc to the combination of favorable sulfur-functionalized surfaces for deposition, charge transfer properties of the perylene layer, and use of the thianthrene+/0 redox couple.

Understanding the Antipathogenic Performance of Nanostructured and Conventional Copper Cold Spray Material Consolidations and Coated Surfaces

The role of high strain rate and severe plastic deformation, microstructure, electrochemical behavior, surface chemistry and surface roughness were characterized for two copper cold spray material consolidations, which were produced from conventionally gas-atomized copper powder as well as spray-dried copper feedstock, during the course of this work. The motivation underpinning this work centers upon the development of a more robust understanding of the microstructural features and properties of the conventional copper and nanostructured copper coatings as they relate to antipathogenic contact killing and inactivation applications. Prior work has demonstrated greater antipathogenic efficacy with respect to the nanostructured coating versus the conventional coating. Thus, microstructural analysis was performed in order to establish differences between the two coatings that their respective pathogen kill rates could be attributed to. Results from advanced laser-induced projectile impact testing, X-ray diffraction, scanning electron microscopy, electron backscatter diffraction, scanning transmission microscopy, nanoindentation, energy-dispersive X-ray spectroscopy, nanoindentation, confocal microscopy, atomic force microscopy, linear polarization, X-ray photoelectron spectroscopy, electrochemical impedance spectroscopy and copper ion release assaying were performed during the course of this research.

Covalent Attachment and Characterization of Perylene Monolayers on Si(111) and TiO2 for Electron-Selective Carrier Transport

We functionalized chemically oxidized Si(111) and TiO₂ surfaces with covalently attached rylene molecules and demonstrated further chemical conversion of the attached species. Base-catalyzed activation of perylene tetracarboxylic dianhydride (PTCDA) preceded reaction with phenylaminosilane-terminated surfaces, yielding surface-bound perylene via an imide linkage. Transflection infrared (IR) spectroscopy of the carbonyl vibrational region elucidated the presence of anhydride, imide, and ester species following each reaction stage. The presence of both anhydride and imide IR features following reaction with PTCDA validates successful perylene attachment. Subsequent functionalization of the surface-attached perylenes yielded IR spectra with little or no detectable anhydride features that indicate successful conversion to ester or imide species based on respective reactions with alkyl bromides or aryl amines. X-ray photoelectron spectroscopy quantified fractional coverages of surface-attached perylene species following a post-deposition derivatization with fluorine-containing alkyl bromides and with anilines. Overlayer model interpretation of the photoelectron results determined a perylene surface coverage of ∼15% relative to the surface density of Si(111) atop sites and a ∼10% surface coverage of imide-terminated perylene species. The interpreted coverage data yield an approximate conversion efficiency for the anhydride-to-imide derivatization at surface-attached perylenes of ∼66%. We discuss the present results in terms of possible coverage and packing on oxide-free silicon surfaces and the utilization of covalently attached rylene species as electron-transporting and hole-blocking connecting layers in molecular electronics and tandem-junction photovoltaic designs.

Detection of adsorbates on emissive MOF surfaces with X-ray photoelectron spectroscopy

The luminescence of azobenzene chromophore struts in a metal organic framework is quenched by nitroaromatic guests. X-ray photoelectron spectroscopic methods verify the emission changes are due to the surface adsorption of the guest molecules rather than encapsulation.