Fe-N-Doped Mesoporous Carbon with Dual Active Sites Loaded on Reduced Graphene Oxides for Efficient Oxygen Reduction Catalysts

Self-Assembly Strategy for Constructing Porous Boron and Nitrogen Co-Doped Carbon as an Efficient ORR Electrocatalyst toward Zinc-Air Battery

Carbon nanomaterials doped with N and B could activate nearby carbon atoms to promote charge polarization through the synergistic coupling effect between N and B atoms, thus facilitating adsorption of O2 and weakening O-O bond to enhance oxygen reduction reaction. Herein, a simple and controllable self-assembly strategy is applied to synthesize porous B, N co-doped carbon-based catalysts (BCN-P), which employs the macrocyclic molecule cucurbit[7]uril (CB7) as nitrogen source, and 3D aromatic-like closo-[B12H12]2- as boron source. In addition, polystyrene microspheres are added to help introduce porous structure to expose more active sites. Benefitting from porous structures and the synergistic coupling effect between N and B atoms, BCN-P has a high onset potential (Eonset=0.846 V) and half-wave potential (E1/2=0.74 V) in alkaline media. The zinc-air battery assembled with BCN-P shows high operating voltage (1.42 V), peak power density (128.7 mW cm-2) and stable charge/discharge cycles, which is even comparable with Pt/C.

Peroxymonosulfate assisted pesticide breakdown: Unveiling the potential of a novel S-scheme ZnO@CoFe2O4 photo-catalyst, anchored on activated carbon

A ternary hetero-junction was prepared by anchoring ZnO@CoFe2O4 (ZCF) on activated carbon (AC) and employed as a UV-assisted peroxymonosulfate (PMS) activator to boost the degradation of diazinon (DZN) pesticide. The structure, morphology, and optical properties of the ZCFAC hetero-junction were characterized through a series of techniques. The highest degradation efficiency of DZN (100% in 90 min) was achieved by the PMS-mediated ZCFAC/UV system, superior to other single or binary catalytic systems due to the strong synergistic effect between ZCFAC, PMS, and UV. The operating reaction conditions, synergistic effects, and the possible pathways of DZN degradation were investigated and discussed. Optical analysis showed that the band-gap energy of the ZCFAC hetero-junction not only enhanced the absorption of UV light but also reduced the recombination of photo-induced electron/hole pairs. Both radical and non-radical species (HO•, SO4•-, O2•-, 1O2, and h+) took part in the photo-degradation of DZN, assessed by scavenging tests. It was found that AC as a carrier not only improved the catalytic activity of CF and ZnO nanoparticles and conferred high stability for the catalyst but also played a crucial role in accelerating the catalytic PMS activation mechanism. Moreover, the PMS-mediated ZCFAC/UV system showed good reusability, universality, and practical applicability potential. Overall, this work explored an efficient strategy for the best use of hetero-structure photo-catalysts towards PMS activation to achieve high performance in decontaminating organic compounds.

Insight into the role of nitrogen in N-doped ordered mesoporous carbons for the spontaneous non-covalent attachment and electrografting of redox-active materials

The role of nitrogen functional groups in nitrogen-doped ordered mesoporous carbons (OMCs) toward the spontaneous non-covalent and electrografting was investigated using two home-made ionic liquid-derived ordered mesoporous carbons having different nitrogen concentrations (guanine-rich ionic liquid-derived ordered mesoporous carbon (GIOMC) and ionic liquid-derived ordered mesoporous carbon (IOMC)). The carbonaceous materials were fabricated by the carbonization of a mixture of ionic liquid (1-methyl-3-phenethyl-1H-imidazolium hydrogen sulfate) as a carbon source using SBA-15 as a hard template. Guanine was used during the carbonization of GIOMC as a nitrogen source. The electrode was modified with either GIOMC or IOMC followed by electrochemical surface functionalization with a few electro-active precursors as redox-active molecular models bearing different substituents and electronic properties. The high surface coverage of 5.6(±0.3) × 10^-9 mol cm^-2 for 4,4-biphenol was obtained for the GIOMC-modified electrode. We seek to explain whether the nitrogen content could indeed exert a dramatic impact on loading electroactive species on the electrode surface. The non-covalent anchoring studies indicated that at higher pH values the loading of electro-active moieties was significantly influenced by the content of nitrogen on the employed OMCs. The adsorption capacity (mg g^-1) of the OMCs was studied for catechol as a typical electro-active species in the range of 0.050-0.165 mg ml^-1. The adsorption capacity of 0.11 mg g^-1 catechol was 42(±4) and 26(±3) mg g^-1 for GIOMC and IOMC, respectively. In addition, our observations revealed that electro-grafting efficiency via diazonium ion was restricted by the protonation of nitrogen in the reaction media. Further, the fabricated redox-active/N-doped OMC electrodes showed sensitivity to pH, which was accompanied by either a Nernstian shift of the redox peak potentials (60(±3) mV per pH) in the pH range of 2-13 in the buffer solutions or variations of the redox peak currents (9.7(±0.3) μA per pH) in the pH range of 1-5.5 in the unbuffered situations. The resulting electrodes as voltammetric pH probes showed a simple response to pH in both buffer and unbuffered solutions. In addition, we introduced the fabricated electrode as a zero-gap generator/collector electrode system using a single electrode to recognize proton-dependent electron transfer from the proton-independent electrode process by detecting pH changes quite close to the surface of the electrode. The detailed descriptions are outlined.

MOF/POM hybrids as catalysts for organic transformations

Insertion of molecular metal oxides, e.g. polyoxometalates (POMs), into metal-organic frameworks (MOFs) opens up new research opportunities in various fields, particularly in catalysis. POM/MOF composites have strong acidity, oxygen-rich surface, and redox capacity due to typical characteristics of POMs and the large surface area, highly organized structures, tunable pore size, and shape are due to MOFs. Such hybrid materials have gained a lot of attention due to astonishing structural features, and hence have potential applications in organic catalysis, sorption and separation, proton conduction, magnetism, lithium-ion batteries, supercapacitors, electrochemistry, medicine, bio-fuel, and so on. The exceptional chemical and physical characteristics of POMOFs make them useful as catalysts in simple organic transformations with high capacity and selectivity. Here, the thorough catalytic study starts with a brief introduction related to POMs and MOFs, and is followed by the synthetic strategies and applications of these materials in several catalytic organic transformations. Furthermore, catalytic conversions like oxidation, condensation, esterification, and some other types of catalytic reactions including photocatalytic reactions are discussed in length with their plausible catalytic mechanisms. The disadvantages of the POMOFs and difficulties faced in the field have also been explored briefly from our perspectives.

Prussian blue analogues derived electrocatalyst with multicatalytic centers for boosting oxygen reduction reaction in the wide pH range

Due to the complex of oxygen reduction reaction (ORR), designing catalysts with multicatalytic centers is considered as a promising way for boosting the ORR. Herein, a multicatalytic centers electrocatalyst Fe₃C/Mn₃O₄ encased by N-doped graphitic layers (FeMn PDA-900) is synthesized using iron manganese Prussian blue analogues and dopamine as the precursor. It exhibits a half-wave potential (E_1/2) of 0.86 V for ORR and yields of H₂O₂ lower than 5% in 0.1 M KOH. Moreover, the prepared catalyst has also shown high catalytic ORR performance in both acidic and neutral electrolyte solutions, which exhibits the potential application in both the proton exchange membrane fuel cell and the microbial electrolysis cell. It is found that the good performance can be well explained by proton-coupled electron transfer mechanism due to the multicatalytic centers from Fe-N_x, Fe₃C and Mn₃O₄ for providing enough active sites at the same time and the N-doped graphitic layers as a bridge for facilitating the electron transfer between the interfaces of Fe₃C/Mn₃O₄ nanoparticles, which paves the way for protons and electrons transfer simultaneously and rapidly, and thus lowing the energy barrier and facilitating the ORR process. Therefore, FeMn PDA-900 is a promising candidate to replace precious metal-based ORR electrocatalysts at the whole pH range.

Two-step facile synthesis of Co3O4@C reinforced PbO2 coated electrode to promote efficient oxygen evolution reaction for zinc electrowinning

The conventional Pb-Ag alloy possesses a high oxygen evolution reaction overpotential, poor stability, and short service life in acidic solutions, making it an unsuitable sort of anode material for the zinc electrowinning process. Therefore, a layered carbon-covered cobalt tetroxide (Co3O4@C)-reinforced PbO2-coated electrode is fabricated via a facile two-step pyrolysis-oxidation and subsequent electrodeposition process. As a result, the reinforced PbO2-coated electrode exhibits a low OER overpotential of 517 mV at 500 A m-2 and a Tafel slope of 0.152 V per decade in a zinc electrowinning simulation solution (0.3 M ZnSO4 and 1.53 M H2SO4). The reduced overpotential of 431 mV at 500 A m-2 compared to traditional Pb-0.76%Ag alloy leads to improved energy savings, which is attributable to the presence of Co3O4@C to refine the grain size and thus increase the effective contact area. Moreover, the reinforced PbO2-coated electrode has a prolonged service life of 93 h at 20 000 A m-2 in 1.53 M H2SO4. Therefore, an accessible and efficient strategy for preparing a coated electrode to improve OER performance for zinc electrowinning is presented in this research.

Heterostructural Interface in Fe3C-TiN Quantum Dots Boosts Oxygen Reduction Reaction for Al-Air Batteries

Oxygen reduction electrocatalysts play important roles in metal-air batteries. Herein, Fe₃C-TiN heterostructural quantum dots loaded on carbon nanotubes (FCTN@CNTs) are prepared as electrocatalysts for the oxygen reduction reaction (ORR) through a one-pot pyrolysis. The Fe₃C-TiN quantum dots with a diameter of 2-5 nm show the unique characteristic of heterostructural interface. The as-prepared FCTN@CNTs display Pt/C comparable ORR performance (E_onset 1.06 and E_1/2 0.95 V) in alkaline medium, which is ascribed to the heterostructural interface between TiN and Fe₃C. Furthermore, the Al-air batteries with the FCTN@CNT catalyst display superior discharge performance, demonstrating good feasibility for practical application. This work provides an effective new method to synthesize affordable and efficient oxygen reduction reaction catalysts.

Molten-salt-assisted synthesis of onion-like Co/CoO@FeNC materials with boosting reversible oxygen electrocatalysis for rechargeable Zn-air battery

A melt-salt-assisted method is utilized to construct an onion-like hybrid with Co/CoO nanoparticles embedded in graphitic Fe-N-doped carbon shells (Co/CoO@FeNC) as a bifunctional electrocatalyst. The iron-polypyrrole (Fe-PPy) is firstly prepared with a reverse emulsion. Direct pyrolysis of Fe-PPy yields turbostratic Fe-N-doped carbon (FeNC) with excellent oxygen reduction reaction (ORR) electrocatalysis, while the melt salt (CoCl₂) mediated pyrolysis of Fe-PPy obtains onion-like Co/CoO@FeNC with a reversible overvoltage value of 0.695 V, largely superior to Pt/C and IrO₂ (0.771 V) and other Co-based catalysts reported so far. The ORR activity is mainly due to the graphitic FeNC and further enhanced by CoN_x bonds, whereas the oxygen evolution reaction (OER) activity is principally due to the Co/CoO composite. Concurrently, Co/CoO@FeNC as cathode catalyst enables Zn-air battery with a high open circuit voltage of 1.42 V, a peak power density of 132.8 mW cm^-2, a specific capacity of 813 mAh g_Zn^-1, and long-term stability.

Metal-Nitrogen-Carbon Catalysts of Specifically Coordinated Configurations toward Typical Electrochemical Redox Reactions

Metal-nitrogen-carbon (M-N-C) material with specifically coordinated configurations is a promising alternative to costly Pt-based catalysts. In the past few years, great progress is made in the studies of M-N-C materials, including the structure modulation and local coordination environment identification via advanced synthetic strategies and characterization techniques, which boost the electrocatalytic performances and deepen the understanding of the underlying fundamentals. In this review, the most recent advances of M-N-C catalysts with specifically coordinated configurations of M-N_x (x = 1-6) are summarized as comprehensively as possible, with an emphasis on the synthetic strategy, characterization techniques, and applications in typical electrocatalytic reactions of the oxygen reduction reaction, oxygen evolution reaction, hydrogen evolution reaction, CO₂ reduction reaction, etc., along with mechanistic exploration by experiments and theoretical calculations. Furthermore, the challenges and potential perspectives for the future development of M-N-C catalysts are discussed.

Non-thermal radiation heating synthesis of nanomaterials

The nanoscale effect enables the unique magnetic, optical, thermal and electrical properties of nanostructured materials and has attracted extensive investigation for applications in catalysis, biomedicine, sensors, and energy storage and conversion. The widely used synthesis methods, such as traditional hydrothermal reaction and calcination, are bulk heating processes based on thermal radiation. Differing from traditional heating methods, non-thermal radiation heating technique is a local heating mode. In this regard, this review summarizes various non-thermal radiation heating methods for synthesis of nanomaterials, including microwave heating, induction heating, Joule heating, laser heating and electron beam heating. The advantages and disadvantages of these non-thermal radiation heating methods for the synthesis of nanomaterials are compared and discussed. Finally, the future development and challenges of non-thermal radiation heating method for potential synthesis of nanomaterials are discussed.

A Unique Ru-N4-P Coordinated Structure Synergistically Waking Up the Nonmetal P Active Site for Hydrogen Production

Numerous experiments have demonstrated that the metal atom is the active center of monoatomic catalysts for hydrogen evolution reaction (HER), while the active sites of nonmetal doped atoms are often neglected. By combining theoretical prediction and experimental verification, we designed a unique ternary Ru-N₄-P coordination structure constructed by monodispersed Ru atoms supported on N,P dual-doped graphene for highly efficient hydrogen evolution in acid solution. The density functional theory calculations indicate that the charge polarization will lead to the most charge accumulation at P atoms, which results in a distinct nonmetallic P active sites with the moderate H∗ adsorption energy. Notably, these P atoms mainly supply highly efficient catalytic sites with ultrasmall absorption energy of 0.007 eV. Correspondingly, the Ru-N₄-P demonstrated outstanding HER performance not only in an acidic condition but also in alkaline environment. Notably, the performance of Ru-NPC catalyst at high current is even superior to the commercial Pt/C catalysts, whether in acidic or alkaline medium. Our in situ synchrotron radiation infrared spectra demonstrate that a P-H_ads intermediate is continually emerging on the Ru-NPC catalyst, actively proving the nonmetallic P catalytically active site in HER that is very different with previously reported metallic sites.

Inner Sphere Electron Transfer Promotion on Homogeneously Dispersed Fe-Nx Centers for Energy-Efficient Oxygen Reduction Reaction

The study reports the optimized incorporation of pyridinic nitrogen in nitrogen-doped carbon nanotubes (CNTs) to realize effective Fe-N_x centers throughout the framework. The study unveils nitrogen as a valuable asset to promote the homogeneous dispersion of Fe moieties throughout the CNT framework, which is a necessary component to institute uniform Fe-N_x centers. In addition, pyridinic nitrogen causes disruption in strongly delocalized π-electrons, which impart electron-withdrawing nature in the carbon matrix, resulting in an anodic shift in oxygen reduction reaction (ORR) onset potential (E_onset). The direct interaction of Fe-N_x with O₂, as evidenced by poisoning and computational studies, ensures the preferential inner sphere electron transfer mechanism. Despite the alkaline medium, the outer sphere electron transfer mechanism was muted, with suppressed HO₂^- generation, preferential 4e^- reduction pathways, and excellent cyclic stability. The study indicates the dependency of ORR half-wave potential on the electron transfer mechanism. The poisoning study unveils the direct involvement of Fe-N_x electroactive centers in facilitating ORR in alkaline medium. It further indicates a noticable increase (up to ∼25%) in peroxide generation-an unwanted ORR intermediate-and concomitant reduction in average electron transfer no. per oxygen molecule.

A cobalt-pyrrole coordination compound as high performance cathode catalyst for direct borohydride fuel cells

Pyrrole and cobalt nitrate were used as nitrogen and metal sources respectively to synthesize a dinitratobis(polypyrrole)cobalt(ii) (Co(polypyrrole)₂(NO₃)₂) adduct as the precursor of a Co–pyrrole/MPC catalyst. Pyrrole has the capability of polymerization and coordination with Co(ii). Taking this advantage, the Co(polypyrrole)₂(NO₃)₂ coordination can form a long-chain structure with abundant and robust Co–N bonds, contributing to significantly increased catalytic sites in the product catalyst. As a result, the obtained Co–pyrrole/MPC (MPC = macroporous carbon) catalyst exhibited high ORR catalytic activity in alkaline media and excellent performance in direct borohydride fuel cell (DBFC). A peak power density up to 325 mW cm⁻² was achieved at ambient condition, outperforming the commercialized Pt/XC-72 benchmark containing 28.6 wt% Pt. The construction of long-chain coordination precursor was verified playing a key role in the electrochemical improvement of Co–pyrrole/MPC catalyst in DBFC.

Co–pyrrole/MPC was synthesized by using pyrrole and cobalt nitrate as nitrogen and metal source, which enabled a higher peak power density than the commercialized 28.6 wt% Pt/XC72 in DBFC.

Bimetallic carbon nanotube encapsulated Fe-Ni catalysts from fast pyrolysis of waste plastics and their oxygen reduction properties

Carbon-based bimetallic electrocatalysts were obtained by catalytic pyrolysis of waste plastics with Fe-Ni-based catalysts and were used as efficient oxygen reduction reaction (ORR) catalysts in this study. The prepared iron-nickel alloy nanoparticles encapsulated in oxidized carbon nanotubes (FeNi-OCNTs) are solid products with a unique structure. Moreover, the chemical composition and structural features of FeNi-OCNTs were determined. The iron-nickel alloy nanoparticles were wrapped in carbon layers, and the carbon nanotubes had an outer diameter of 20-50 nm and micron-scale lengths. FeNi-OCNT with a Fe/Ni ratio of 1:2 (FeNi-OCNT12) exhibited remarkable electrochemical performance as an ORR catalyst with a positive onset potential of 1.01 V (vs. RHE) and a half-wave potential of 0.87 V (vs. RHE), which were comparable to those of a commercial 20% Pt/C catalyst. Furthermore, FeNi-OCNT12 exhibited promising long-term stability and higher tolerance to methanol than the commercial 20% Pt/C catalyst in an alkaline medium. These properties were attributable to the protective OCNT coating of the iron-nickel alloy nanoparticles.

In-MOF-derived ultrathin heteroatom-doped carbon nanosheets for improving oxygen reduction

For electrocatalysis, the development of highly active and low-cost stable electrocatalysts, which would be directly applied in cathodes for fuel cells that are regarded as the most promising candidates for clean energy conversion in the quest for alternatives to conventional fossil fuel technology, remains a massive challenge. In this context, oxygen reduction reaction (ORR) is a critical process under intense research for the direct conversion of chemical energy into electricity. Herein, a facile synthetic method is proposed for the preparation of hierarchically porous 2-dimensional nanosheets consisting of Fe4C and FeCo nanoparticles incorporated in N/S-doped carbon materials at 900 °C, denoted as InFeCo@CNS900. This composite can be conveniently prepared by directly calcining the crystalline indium-organic framework of InOF-24, which is impregnated with the ferric thiocyanate and cobalt ammonium complexes under Ar atmosphere, in which Fe4C and FeCo nanoparticles were in situ formed and embedded into the well-developed carbon materials, which display the hierarchically porous nanosheets with microporous and mesoporous structures. Due to the synergistic effects between different active substances, high specific surface area, suitable graphitization degree, and rich active sites, the as-obtained InFeCo@CNS900 electrocatalyst exhibits an excellent ORR activity, which shows a lower Tafel slope of 59.5 mV dec-1, higher diffusion limit current of 5.15 mA cm-2, and better stability than the commercial 20 wt% Pt/C catalyst. This study provides a facile approach for the design and synthesis of highly efficient non-noble metal-doped carbon materials with a unique 2-dimensional morphology, which are potentially applied in energy science and technology.

Preparation of Iron- and Nitrogen-Codoped Carbon Nanotubes from Waste Plastics Pyrolysis for the Oxygen Reduction Reaction

A novel method for the preparation of iron- and nitrogen-codoped carbon nanotubes (Fe-N-CNTs) is proposed, based on the catalytic pyrolysis of waste plastics. First, carbon nanotubes are produced from pyrolysis of plastic waste over Fe-Al₂ O₃ ; then, Fe-CNTs and melamine are heated together in an inert atmosphere. Different co-pyrolysis temperatures are tested to optimize the electrocatalyst production. A high doping temperature improves the degree of graphite formation and promotes the conversion of nitrogen into a more stable form. Compared with commercial Pt/C, the electrocatalyst obtained from pyrolysis at 850 °C shows remarkable properties, with an onset potential of 0.943 V versus RHE and a half-wave potential of 0.811 V versus RHE, and even better stability and anti-poisoning properties. In addition, zinc-air battery tests are performed, and the optimized catalyst exhibits a high maximum power density.

Liberating N-CNTs Confined Highly Dispersed CoNx Sites for Selective Hydrogenation of Quinolines

Selective hydrogenation of quinoline and its derivatives is an important means to produce corresponding 1,2,3,4-tetrahydroquinolines for a wide spectrum of applications. A facile and efficient "laser irradiation in liquid" technique to liberate the inaccessible highly dispersed CoN_x active sites confined inside N-doped carbon nanotubes is demonstrated. The liberated CoN_x sites possess generic catalytic activities toward selective hydrogenation of quinoline and its hydroxyl, methyl, and halogen substituted derivatives into corresponding 1,2,3,4-tetrahydroquinolines with almost 100% conversion efficiency and selectivity. This laser irradiation treatment approach should be widely applicable to unlock the catalytic powers of inaccessible catalytic active sites confined by other materials.

Laser-synthesized graphite carbon encased gold nanoparticles with specific reaction channels for efficient oxygen reduction

Developing novel electrocatalysts with desirable activity and stability is always full of challenge in electrochemical energy conversion. Here, specific carbon shell encapsulated Au (Au@C) nanoparticles are prepared by a laser ablation in liquids method and used as the oxygen reduction reaction (ORR) electrocatalysts. Such Au@C nanoparticles exhibit excellent catalytic activity toward ORR with an onset potential of 0.98 V and a half-wave potential of 0.87 V, better than that of commercial Pt/C. More importantly, the Au@C catalyst exhibits unrivalled stability for 3000 CV cycles for ORR in 0.1 M KOH, dramatically superior to Pt/C and pure Au catalysts. The density functional theory (DFT) calculations and SCN^- ions to poison metal-based active sites are conducted to Au@C catalyst, and the results indicate that the structural defects of carbon shells supply an access for the reactants to contact the core Au nanoparticles, causing the catalytic reaction, meanwhile the carbon shells prevent the degeneration of core Au nanoparticles in the harsh electrolytes enhancing the durability of Au effectively.

Oxygen reduction reaction performance of Fe-N/C catalysts from ligand-iron coordinative supramolecular precursors

Simultaneous introduction of both transition metal and other inorganic elements into the carbon matrix has attracted great attention in the fabrication of carbon materials with high electrochemical properties. Herein, rational design of ligand-iron coordinative supramolecular precursors is achieved for the fabrication of Fe-N/C catalysts, which possess high oxygen reduction reaction (ORR) performance. A series of precursors are prepared by a simple coordination reaction between a three armed catechol monomer and iron ions. Particular interest is focused on tuning the doping species, surface area and morphology of the Fe-N/C catalysts through a simple selection of iron resources. We show that an Fe-N/C catalyst derived from Fe₂(SO₄)₃ at a carbonization temperature of 800 °C, has the optimized ORR performance with an onset potential of 0.930 V and half-wave potential of 0.801 V. Detailed investigation indicates that the synergistic effect among doping elements of nitrogen and sulfur and the unique carbon structure determines the performance of the Fe-N/C catalysts. Our findings may be of significance for the fabrication of doped carbon materials using coordinative supramolecular polymers as precursors.

Efficient oxygen reduction on sandwich-like metal@N-C composites with ultrafine Fe nanoparticles embedded in N-doped carbon nanotubes grafted on graphene sheets

In the past decade, tremendous efforts have been devoted to the search for the alternatives to Pt-based catalysts for the oxygen reduction reaction (ORR) in fuel cells and metal-air batteries. Recently, metal-nitrogen-carbon (M-N-C) systems, especially 3d transition metals (TM) and their alloys encapsulated in nitrogen-doped carbon based materials (TM@N-C), have attracted increasing attention due to their low cost and high ORR activity. Here, a simple and novel strategy is developed to synthesize sandwich-structured TM@N-C composites, in which ultrafine Fe nanoparticles are encapsulated in nitrogen-doped carbon nanotubes (N-CNTs) grafted on both sides of reduced graphene oxide (rGO) sheets by pyrolysis of ammonium ferric citrate-functionalized zeolitic imidazolate framework-8@graphene oxide (Fe@ZIF-8@GO). The resulting Fe@N-CNTs@rGO composites naturally integrate zero-dimensional (0D) Fe nanoparticles, one-dimensional (1D) N-CNTs, and two-dimensional (2D) graphene into a three-dimensional (3D) hierarchical architecture with highly dispersed active sites, a large surface area, and abundant porosity. Because of these structural advantages, the sandwich-structured Fe@N-CNTs@rGO composites display a half-wave potential of 0.83 V in a 0.1 M KOH solution for the ORR, comparable to that of commercial Pt/C catalysts, and more excellent durability and resistance to fuel molecules. The proposed strategy paves a new way for the synthesis of non-precious high-performance electrocatalysts for energy conversion applications.

Tunable engineering hollow carbon nanomaterial served as an excellent catalyst for oxygen reduction reaction and hydrogen evolution reaction

Fe and N functionalized hollow carbon spheres (Fe/N-HCS) with hierarchically porous structure are constructed. Remarkably, it is discovered that the pyrolysis temperature effects the chemical composition intensively. At 800 °C, only graphitic-N and oxidized-N are formed for all as-prepared samples. The surface area and pores can be precisely tuned, the surface area of all Fe/N-HCS samples is more than 500  m² g^-1 benefiting from the porous hollow structure. Thus, the optimized Fe/N-HCS exhibits excellent oxygen reduction reaction performance in term of onset potential (1.00 V vs. RHE), half-wave potential (0.87 V vs. RHE), good stability as well as methanol tolerance for oxygen reduction reaction, even surpassing the Pt in alkaline condition and more competitive in acidic condition; Furthermore, the optimized Fe/N-HCS displays better hydrogen evolution reaction activity in acidic condition with onset overpotential of 40 mV and overpotential to deliver 10 mA cm^-2 at 170 mV, indicating better active. It is found that Fe/N-HCS improve the hydrogen evolution reaction activity after electrodeposition trace quantity of Pt, which shows 170 mV of overpotential to deliver 100 mA cm^-2. X-ray photoelectron spectroscopy result indicates the loading of Pt is roughly 0.11 at%, thus, the improved performance is basically due to the synergistic effect between Pt and Fe/N-HCS.

Atomic Fe Dispersed on N-Doped Carbon Hollow Nanospheres for High-Efficiency Electrocatalytic Oxygen Reduction

Exploration of high-efficiency, economical, and ultrastable electrocatalysts for the oxygen reduction reaction (ORR) to substitute precious Pt is of great significance in electrochemical energy conversion devices. Single-atom catalysts (SACs) have sparked tremendous interest for their maximum atom-utilization efficiency and fascinating properties. Therefore, the development of effective synthetic methodology toward SACs becomes highly imperative yet still remains greatly challenging. Herein, a reliable SiO₂ -templated strategy is elaborately designed to synthesize atomically dispersed Fe atoms anchored on N-doped carbon nanospheres (denoted as Fe-N-C HNSs) using the cheap and sustainable biomaterial of histidine (His) as the N and C precursor. By virtue of the numerous atomically dispersed Fe-N₄ moieties and unique spherical hollow architecture, the as-fabricated Fe-N-C HNSs exhibit excellent ORR performance in alkaline medium with outstanding activity, high long-term stability, and superior tolerance to methanol crossover, exceeding the commercial Pt/C catalyst and most previously reported non-precious-metal catalysts. This present synthetic strategy will provide new inspiration to the fabrication of various high-efficiency single-atom catalysts for diverse applications.

Controllable conversion of Prussian blue@yeast bio-template into 3D cage-like magnetic Fe3O4@N-doped carbon absorbent and its cohesive regeneration by persulfate activation

A multitude of heteroatom-doped carbon adsorbents have been explored to cope with ever-growing organic pollution. However, development of these advanced carbon materials with adequate activity and stability remains challenging. Herein, unique 3D cage-like magnetic N-doped Fe3O4@C adsorbents were rationally constructed by a one-step pyrolysis of Prussian blue@yeast (PB@yeast) bio-templates. By using yeast as an available biological support, the prepared Fe3O4@C hybrids were demonstrated to provide a sufficient number of Fe, N and C atoms for the novel cage-like microstructures, making them a new type of Fe, N co-doped carbon absorbents with a facile preparation procedure and remarkable adsorption behavior. Rhodamine B (RhB) removal indicated that the prepared N-doped Fe3O4@C adsorbents displayed high adsorption capabilities in a near-neutral solution, and Fe3O4@C (1 : 0.11) exhibited a maximum adsorption capability of 257.06 mg g-1. More importantly, spent N-doped Fe3O4@C absorbents, which could be recovered by magnetic separation and cohesive persulfate (PS) activated photo-Fenton regeneration, showed excellent adsorption reusability and high stability even after 5 cycles. Overall, this paper presents a simple method for fabrication of a 3D cage-like magnetic N-doped Fe3O4@C adsorbent, which provides a significant guidance for the study of Fe, N co-doped carbon adsorbents towards dye wastewater treatment.

FeNC/MXene hybrid nanosheet as an efficient electrocatalyst for oxygen reduction reaction

The iron–nitrogen–carbon (FeNC) catalyst, as a highly active and stable non-precious metal catalyst, has emerged as one of the most promising alternatives to replace the platinum catalyst for oxygen reduction reaction (ORR). Herein, a novel FeNC/MXene hybrid nanosheet was, for the first time, explored via pyrolysis of an iron–ligand complex and MXene nanosheets. The structure and morphology characterizations reveal that a thin and rugged FeNC coating was closely attached on the surface of MXene, forming a hybrid nanosheet structure with an excellent conductive substrate and many electrocatalytic active sites on the substrate. The electrochemical measurements disclose that the FeNC/MXene hybrid nanosheet exhibited a remarkable electrocatalytic performance, with a 25 mV higher half-wave potential (0.814 V versus RHE) than the Pt/C counterpart. More importantly, this hybrid presented a superb durability, with only 2.6% decay after a 20 000 s continuous test, much better than the 15.8% degradation for Pt/C. This work not only demonstrates the promising performance of the FeNC/MXene hybrid nanosheet for ORR, but more importantly provides new insight into the rational design of non-noble-metal catalysts using an MXene support.

A novel FeNC/MXene hybrid nanosheet with a rugged FeNC coating closely attached on the MXene surface was explored, which exhibited remarkable electrocatalytic activity with a superb durability (only 2.6% decay after a 20 000 s continuous test).

Systematic exploration of N, C configurational effects on the ORR performance of Fe–N doped graphene catalysts based on DFT calculations

Metal single-atom catalysts (MSATs), such as Fe–N coordination doped sp²-carbon matrices, have emerged as a promising oxygen reduction reaction (ORR) catalyst to replace their costly platinum (Pt) based counterparts in fuel cells. In this work, we employ density functional theory (DFT) to systematically discuss the electronic-structure and surface-stress effects of N, C configurations on Fe–N doped graphene in single and double vacancy. The formation energy (E_f) of Fe–N-gra dropped off with the increase of N atoms incorporated for both single and double vacancy groups. The theoretical overpotentials on Fe–N–C sites were calculated and revealed that moderate N-doping levels and doping configuration could enhance the ORR activity of Fe–N coordination structures in the double vacancy and that doping N atoms is not effective for ORR activity in single vacancy. By exploring the d-band centers, we found that ligand effects and surface tension effects contribute to the modification of the d-band centers of metal Fe atoms. An optimum Fe–N–C ORR catalyst should exhibit moderate surface stress properties and an ideal N, C ligand configuration. This study provides new insight into the effects of N atom doping in Fe–N-gra catalysts and could help guide the rational design of high-performance carbon-based ORR electrocatalysts.

An optimum Fe–N–C ORR catalyst should exhibit a moderate surface stress property and an ideal N, C ligand configurations that results in a moderate interaction between the ORR intermediates and its surface sites.

Fe/N-doped carbon nanofibers with Fe3O4/Fe2C nanocrystals enchased as electrocatalysts for efficient oxygen reduction reaction

A Fe-based carbon material with multi active sites of Fe–N_x, Fe₃O₄ and Fe₂C for oxygen reduction was synthesized through facile pyrolysis of a Fe–porphyrin conjugated microporous polymer.

Lewis-Basic Lanthanide Metal-Organic Framework-Derived Versatile Multi-Active-Site Synergistic Catalysts for Oxygen Reduction Reaction

Oxygen reduction reaction underpins the development of the whole fuel-cell field, where there is a strong impetus to develop efficient and stable catalysts that can replace the precious metal Pt/C. Herein, a series of excellent catalysts for ORR derived from Ce/La dual lanthanide metal-organic framework with functional Lewis-basic sites were synthesized for the first time. The synergistic effect of high concentration of oxygen vacancies from La-embedded CeO₂ and Fe-N _x sites as well as porous structure endows the catalyst superior performance to Pt/C, with a half-wave potential ( E_1/2) of 0.870 V and a current density ( j) of 5.43 mA/cm². Furthermore, the catalysts are also effective for other nonelectrocatalytic reactions. It is expected that this research will contribute to synthesis of an excellent nonplatinum electrocatalyst for fuel-cell applications, and the oxygen vacancies stabilized in carbon matrix offer a method for versatile catalyst design for other reactions.

Melamine formaldehyde–metal organic gel interpenetrating polymer network derived intrinsic Fe–N-doped porous graphitic carbon electrocatalysts for oxygen reduction reaction

Melamine formaldehyde metal organic gel interpenetrating networks for heteroporous Fe–N-doped carbon.