Emulsion Electrospinning of Polytetrafluoroethylene (PTFE) Nanofibrous Membranes for High-Performance Triboelectric Nanogenerators

Fabrication of hollow fiber composite membranes via opposite transmission reaction method for dye/salt separation

The separation layer prepared by the conventional coating-crosslinking method is typically thick and prone to forming defective macropores, significantly affecting the water permeability and dye/salt separation performance of membranes. This work presented a novel method to prepare hollow fiber composite membranes for dye/salt separation based on the opposite transmission reaction of crosslinker. In this method, the macromolecule in situ reacted with a small-molecule crosslinker at the openings of membrane pore channels, forming a separation layer with discontinuous sheet-like and granular structure. Compared to the conventional forward coating-crosslinking method, the separation layer prepared by the opposite transmission reaction method exhibited an ultra-thin thickness of 29.1 nm. Consequently, the composite membrane exhibited a high water permeability of 72.7 L·m-2·h-1·bar-1, which was 2.3 times higher than that of conventional methods. Moreover, the prepared composite membrane presented a more uniformed pore structure, completely retaining the VBB (100%) with a low Na2SO4 rejection of 4.3%, demonstrating excellent dye/salt separation performance. Additionally, the prepared composite membrane exhibited superior anti-fouling properties compared to that prepared by the conventional method. Therefore, the opposite transmission reaction method proposed in this study held promising applications in the preparation of hollow fiber composite membranes for efficient dye/salt separation.

Multi-Attribute Triboelectric Materials and Innovative Applications Via TENGs

Triboelectric nanogenerators (TENGs) as an avant-garde technology that transforms mechanical energy into electrical energy, offering a new direction for green energy and sustainable development. By means of high-efficiency TENGs, conventional materials as new triboelectric materials have exhibited multi-attribute characteristics, achieving innovative applications in the field of micro-nano energy harvesting and self-powered sensing. The progress of TENGs technology with the triboelectric materials is complementary and mutually promoting. On the one hand, one of the cruxes of TENGs lies in the triboelectric materials, which have a decisive impact on their performance. On the other hand, as the research and application of TENGs continue to deepen, higher demands are placed on triboelectric materials, which in turn promotes the advancement of the entire material system as well as the fields of materials science and physics. This work aims to delve into the characteristics, types, preferred choices, and modification treatments of triboelectric materials on the performances of TENGs, hoping to provide guidance and insights for future research and applications.

All-Cellulose Nanofiber-Based Sustainable Triboelectric Nanogenerators for Enhanced Energy Harvesting

Triboelectric nanogenerators (TENGs) show promising potential in energy harvesting and sensing for various electronic devices in multiple fields. However, the majority of materials currently utilized in TENGs are unrenewable, undegradable, and necessitate complex preparation processes, resulting in restricted performance and durability for practical applications. Here, we propose a strategy that combines straightforward chemical modification and electrospinning techniques to construct all-cellulose nanofiber-based TENGs with substantial power output. By using cellulose acetate (CA) as the raw material, the prepared cellulose membranes (CMs) and fluorinated cellulose membranes (FCMs) with different functional groups and hydrophobic properties are applied as the tribopositive and tribonegative friction layers of FCM/CM-based triboelectric nanogenerators (FC-TENGs), respectively. This approach modulates the microstructure and triboelectric polarity of the friction materials in FC-TENGs, thus enhancing their triboelectric charge densities and contact areas. As a result, the assembled FC-TENGs demonstrate enhanced output performance (94 V, 8.5 µA, and 0.15 W/m2) and exceptional durability in 15,000 cycles. The prepared FC-TENGs with efficient energy harvesting capabilities can be implemented in practical applications to power various electronic devices. Our work strengthens the viability of cellulose-based TENGs for sustainable development and provides novel perspectives on the cost-effective and valuable utilization of cellulose in the future.

Advances of Strategies to Increase the Surface Charge Density of Triboelectric Nanogenerators: A Review

Triboelectric nanogenerators (TENGs) have manifested a remarkable potential for harvesting environmental energy and have the prospects to be utilized for various uses, for instance, self-powered sensing devices, flexible wearables, and marine corrosion protection. However, the potential for further development of TENGs is restricted on account of their low output power that in turn is determined by their surface charge density. The current review majorly focuses on the selection and optimization of triboelectric materials. Subsequently, various methods capable of enhancing the surface charge density of TENGs, including environmental regulation, charge excitation, charge pumping, electrostatic breakdown, charge trapping, and liquid-solid structure are comprehensively reviewed. Lastly, the review is concluded by highlighting the existing challenges in enhancing the surface charge density of TENGs and exploring potential opportunities for future research endeavors in this area.

Boosting the Electrical Performance of PLA-Based Triboelectric Nanogenerators for Sustainable Power Sources and Self-Powered Sensing

Triboelectric nanogenerators (TENGs) have emerged as a promising technology for harvesting mechanical energy from the ambient environment. However, developing tribopositive materials with strong piezoelectric effects and high electron-donating ability still remains a challenge. Herein, poly(ethylene glycol) monomethyl ether (mPEG) to soft poly(lactic acid) (PLA) is adopted, then PLA/mPEG nanofibers are fabricated under electrospinning and used as the tribopositive material for fabricating robust power density TENGs. The crystallinity and dynamic mechanical properties of PLA/mPEG nanofibers are investigated. The results revealed that the incorporation of mPEG provided an effective approach to elevate the electron-donating ability and charge transfer efficiency in PLA. The PLA/mPEG-based TENGs achieved a high open-circuit voltage of 342.8 V, a short-circuit current of 38.5 µA, and a maximum power density of 116.21 W m-2 over a 2 cm2 contact area at an external load of 106 Ω, respectively. Strikingly, excellent stability and durability are demonstrated after continuous cycles up to 104 cycles. Noteworthy, the TENGs are explored for self-powered sensing applications, with seven TENG units integrated to act as self-powered sensors playing music through buzzers when pressed by fingers. Eventually, this work provides new insights into tuning the structures and properties of electrospun polymers to reinforce the TENG output and self-powered systems.

Robust Piezoelectric Biomolecular Membranes from Eggshell Protein for Wearable Sensors

Flexible and wearable devices are drawing increasing attention due to their promising applications in energy harvesting and sensing. However, the application of wearable devices still faces great challenges, such as flexibility, repeatability, and biodegradability. Biopiezoelectric materials have been regarded as favorable energy-harvesting sources due to their nontoxicity and biocompatibility. Here, a wearable and biodegradable sensor is proposed to monitor human activities. The proposed sensor is fabricated via a low-cost, facile, and scalable electrospinning technology from nanofibers composed of eggshell membranes mixed with polyethylene oxide. It is shown that the sensor exhibits excellent flexibility, outstanding degradability, and mechanical stability over 3000 cycles under periodic stimulation. The device displays multiple potential applications, including the recognition of different objects, human motion monitoring, and active voice recognition. Finally, it is shown that the composite nanofiber membrane has good degradability and breathability. With excellent sensing performance, environmental friendliness, and ease of processing, the eggshell membrane-based sensor could be a promising candidate for greener and more environmentally friendly devices for application in implantable and wearable electronics.

Highly porous and rough polydimethylsiloxane film-based triboelectric nanogenerators and its application for electrochemical cathodic protection

The development and utilization of triboelectric nanogenerator (TENG) are very important for realizing energy cleaning in electrochemical processes. However, limited electrical output performance plays a major stumbling block to this process. Herein, a porous and high-roughness PDMS (PR/PDMS) negative friction layer was obtained by doping PDMS with powdered chitosan and casting using a sacrificial anodic alumina template. A TENG was fabricated by the PR/PDMS with Al film (PR-TENG). The PR-TENG exhibited much better performance than the pure PDMS-based TENG, which was attributed to the porous properties of the PR/PDMS. Under the driving of external mechanical force at 5 Hz, the PR-TENG showed a maximum output open-circuit voltage (Voc) and short-circuit current density (Jsc) of 77.1 V and 33.9 mA/m2, respectively. To prove the concept, the electrochemical cathodic protection system with PR-TENG was constructed. Ultimately, the application prospects of the PR-TENG as a clean energy source for electrochemical processes were explored and evaluated.

Amorphous Poly (Aryl Ether Ketones) Containing Methylene Groups with Excellent Thermal Resistance, Dielectric Properties and Mechanical Performance

Low-dielectric constant polymers are widely used in various microelectronic materials. With the development of 5G communication technology, there is an urgent need for polymer materials with low dielectric constant at high frequency, good thermal resistance, and mechanical properties. In this study, four novel poly (aryl ether ketone) (PAEK) containing different numbers of methylene groups were synthesized via nucleophilic polycondensation reaction. At 10 GHz, these polymer films exhibit excellent dielectric properties with dielectric constants as low as 2.76. The relationship between the dielectric constant and the number of methylene groups is illustrated by constructing the amorphous accumulation cell model. In addition, methylene groups provided the polymer with favorable mechanical performance, including Young's modulus in the range of 2.17-2.21 GPa, the tensile strength from 82.0 to 88.5 MPa and the elongation at the break achieved 7.94%, respectively. Simultaneously, the polymer maintains good thermal resistance with a glass transition temperature (Tg) reaching 216 °C. The result indicates that the obtained novel PAEK is potentially valuable in the field of high-frequency communications.

Mechanically Robust and Electrically Stable High-Performance Triboelectric Nanogenerator Based on Fluffy-Free EC/Nylon-11 and PTFE/PVDF Nanofibers

Electrospun nanofiber (NF)-based triboelectric nanogenerators (TENGs) have attracted significant attention in recent years due to their high specific surface area, flexibility, and facile fabrication. However, these TENGs' triboelectric (TE) layers composed of electrospun NFs fail easily due to the poor mechanical properties and fluffy characteristics of the NFs. Herein, electropositive and electronegative TE layers based on ethylcellulose-coated nylon-11 (EC/nylon-11) NFs and polytetrafluoroethylene-coated poly(vinylidene fluoride) (PTFE/PVDF) NFs are prepared via electrospinning and postcoating processes. The obtained EC/nylon-11 and PTFE/PVDF NFs are fluffy-free and exhibit 12.26 and 20.33-fold enhancements of Young's modulus compared with those of pure nylon-11 and PVDF NFs, respectively. The optimized TENG exhibits not only superior performance, including an open-circuit voltage (VOC) of 212 V, a short-circuit current (ISC) of 18.5 μA, and a maximum power density of 1.76 W/m2 but also excellent electrical durability for over 100,000 cycles. The TENG's capability is further demonstrated by continuously driving electronics for over 5 min and by being integrated into a self-powered sensor array of electric skin to detect different in vitro stimuli. This work provides an effective approach to obtaining mechanically robust and electrically stable NF-based high-performance TENGs, which may have potential applications in durable, wearable, and self-powered nanoelectronics.

Design and Synthesis of Low Dielectric Poly(aryl ether ketone) from Incorporation Bulky Fluorene Groups and Regular Hydroquinone Structure

To decrease the dipole polarization rate and reduce the dielectric constant of poly(aryl ether ketone) (PAEK) resin, 1,4-di(4-fluorobenzoyl) cyclohexane (DFBCH), a weakly polarizing cyclohexane-based monomer, was designed and synthesized as the primary reactant. The bulky fluorene group was incorporated to increase the free volume of the resin, further reducing the dielectric constant. Additionally, hydroquinone with a symmetric and regular structure was utilized to enhance the molecular chain's regularity and reduce dipole relaxation, further lowering the resin's dielectric constant and dielectric loss. The PFQEKs series resins exhibited excellent thermal stability with glass transition temperature (Tg) ranging from 222 to 239 °C and 5% weight loss (Td5%) ranging from 458 to 463 °C, with different monomer ratios. As the hydroquinone content increased, the dielectric constant (Dk) and dielectric loss (Df) of the resin decreased significantly, with Dk ranging from 2.92 to 2.77 and Df ranging from 0.011 to 0.008 at 10 GHz.

Mechanism and optimum pressure for sliding-mode nanogenerator

Triboelectric nanogenerator has extensive applicability because of its capability of harvesting mechanical energy and flexible working modes. To research the optimum pressure and improve the recovered energy of the sliding-mode triboelectric nanogenerator, a contact model of the Al/PTFE tribo-pair is studied by ab initio calculation and finite element simulation. The F-atom of PTFE is proved to be the electron accepter and the charges transferred can be predicted by Bader charge analysis. The mathematical relation between interfacial distance, charges transferred and contact pressure can be fitted. By Gauss’s law, the electric field is simulated and the regeneration energy of the sliding-mode triboelectric nanogenerator can be evaluated by the total electric energy and friction loss. Finally, an optimum pressure can be set to the upper or lower limit of working pressure corresponding to larger recovered energy. And less friction coefficient and larger contact area are also effective methods for recovering energy.

Fluidics for energy harvesting: from nano to milli scales

A large amount of untapped energy sources surrounds us. In this review, we summarize recent works of water-based energy harvesting systems with operation scales ranging from miniature systems to large scale attempts. We focus particularly on the triboelectric energy, which is produced when a liquid and a solid come into contact, and on the osmotic energy, which is released when salt water and fresh water are mixed. For both techniques we display the state of the art understanding (including electrical charge separation, electro-osmotic currents and induced currents) and the developed devices. A critical discussion of present works confirms the significant progress of these water-based energy harvesting systems in all scales. However, further efforts in efficiency and performance amelioration are expected for these technologies to accelerate the industrialization and commercialization procedure.

Rational Design of Advanced Triboelectric Materials for Energy Harvesting and Emerging Applications

The properties of materials play a significant role in triboelectric nanogenerators (TENGs). Advanced triboelectric materials for TENGs have attracted tremendous attention because of their superior advantages (e.g., high specific surface area, high porosity, and customizable macrostructure). These advanced materials can be extensively applied in numerous fields, including energy harvester, wearable electronics, filtration, and self-powered sensors. Hence, designing triboelectric materials as advanced functional materials is important for the development of TENGs. Herein, the structural modification methods based on electrospinning to improve the triboelectric properties and the latest research progress in this kind of TENGs are systematically summarized. Preparation methods and design trends of nanofibers, microspheres, hierarchical structures, and doping nanomaterials are highlighted. The factors influencing the formation and properties of triboelectric materials are considered. Furthermore, the latest progress on the applications of TENGs is systematically elaborated. Finally, the challenges in the development of triboelectric materials are discussed, thereby guiding researchers in the large-scale application of TENGs.

Nanofibrous polytetrafluoroethylene/poly(ε-caprolactone) membrane with hierarchical structures for vascular patch

With the prevalence of cardiovascular diseases, developing cardiovascular supplements is becoming increasingly urgent. The ability of cells to rapidly adhere and proliferate to achieve endothelialization is extremely important for vascular grafts. In this work, we electrospun polytetrafluoroethylene (PTFE) nanofibrous membranes and used induced crystallization to manufacture poly(ε-caprolactone) (PCL) shish-kebab microstructures on PTFE nanofibers to overcome the inertness of PTFE, and promote cell adhesion and proliferation. PCL lamella periodically grew on the surface of PTFE nanofibers yielding a hierarchical structure, which improved the biocompatibility and mechanical properties of the PTFE nanofibrous membrane. The deposition of PCL lamella improved the hydrophilicity of electrospun PTFE nanofibers membrane, leading to good cell proliferation and adhesion. Also, due to the surface inertness of the substrate material PTFE, this PTFE/PCL composite film has good anti-platelet adhesion properties. Furthermore, cell proliferation could be regulated by controlling the integrity of the PCL crystal network. The vascular patch showed similar mechanical properties to natural blood vessels, providing a new strategy for vascular tissue engineering.

High-Output Lotus-Leaf-Bionic Triboelectric Nanogenerators Based on 2D MXene for Health Monitoring of Human Feet

As versatile energy harvesters, triboelectric nanogenerators (TENGs) have attracted considerable attention in developing portable and self-powered energy suppliers. The question of how to improve the output power of TENGs using cost-effective means is still under vigorous investigation. In this paper, high-output TENGs were successfully produced by using a simple and low-cost lotus-leaf-bionic (LLB) method. Well-distributed microstructures were fabricated via the LLB method on the surface of a polydimethylsiloxane (PDMS) negative triboelectric layer. 2D MXene (Ti₃C₂T_x) and graphene were doped into the structured PDMS to evaluate their effects on the performance of TENG. Owing to merits of the MXene doping and microstructures on the PDMS surface, the output power of MXene-doped LLB TENGs reached as high as 104.87 W/m², which was about 10 times higher than that of graphene-doped devices. The MXene-doped LLB TENGs can be used as humidity sensors, with a sensitivity of 4.4 V per RH%. In addition, the MXene-doped LLB TENGs were also sensitive to human body motions; hence, a foot health monitoring system constructed by the MXene-doped LLB TENGs was successfully demonstrated. The results in this work introduce a way to produce cost-effective TENGs using bionic means and suggest the promising applications of TENGs in the smart monitoring system of human health.

Research progress of low dielectric constant polymer materials

The advent of high frequency communication era presents new challenges for further development of dielectric polymer materials. In the field of communication, efficient signal transmission is critical. The lower the dielectric constant of the dielectric material used, the lower the signal delay and the higher the signal fidelity. The preparation of polymer materials with low dielectric constant or reduce the dielectric constant of polymer materials becomes a key research topic. Summarizing past progress and providing perspective, this paper primarily discusses the intrinsic low dielectric polymers, fluorine doped low dielectric polymers, and microporous low dielectric polymers, while predicting the research trend of low dielectric materials.

Recent Progress Regarding Materials and Structures of Triboelectric Nanogenerators for AR and VR

With the continuous advancement in technology, electronic products used in augmented reality (AR) and virtual reality (VR) have gradually entered the public eye. As a result, the power supplies of these electronic devices have attracted more attention from scientists. Compared to traditional power sources, triboelectric nanogenerators (TENGs) are gradually being used for energy harvesting in self-powered sensing technology such as wearable flexible electronics, including AR and VR devices due to their small size, high conversion efficiency, and low energy consumption. As a result, TENGs are the most popular power supplies for AR and VR products. This article first summarizes the working mode and basic theory of TENGs, then reviews the TENG modules used in AR and VR devices, and finally summarizes the material selection and design methods used for TENG preparation. The friction layer of the TENG can be made of a variety of materials such as polymers, metals, and inorganic materials, and among these, polytetrafluoroethylene (PTFE) and polydimethylsiloxane (PDMS) are the most popular materials. To improve TENG performance, the friction layer material must be suitable. Therefore, for different application scenarios, the design methods of the TENG play an important role in its performance, and a reasonable selection of preparation materials and design methods can greatly improve the work efficiency of the TENG. Lastly, we summarize the current research status of nanogenerators, analyze and suggest future application fields, and summarize the main points of material selection.

Flexible Triboelectric Nanogenerators Based on Electrospun Poly(vinylidene fluoride) with MoS2/Carbon Nanotube Composite Nanofibers

With the miniaturization of wearable smart devices, the demand for portable and sustainable power sources is increasing. Herein, a flexible and lightweight triboelectric nanogenerator (PMC-TENG) was fabricated with MoS₂/carbon nanotube (MC)-doped PVDF as the friction substrate based on electrospinning for harvesting random body motion energy under complex mechanical deformations. The charge density on the friction surface of PVDF nanofibers was found to increase significantly as the introduced electron acceptor of the MC composite, and nylon as a clothing material for another friction layer simplifies the structure of the device. Upon optimization of the electrospinning preparation process, the output voltage of the prepared PMC-TENG can reach >300 V and the instantaneous power can reach 0.484 mW (∼6 cm × 6 cm). At the same time, the PMC-TENG remains stable over 3000 cycles and has the ability to charge a capacitor. The flexible device demonstrates an excellent capability of converting mechanical energy to electrical energy. Therefore, this study has good prospects for application in the field of power supply for portable electronic devices and others.

A fluorescent triboelectric nanogenerator manufactured with a flexible janus nanobelt array concurrently acting as a charge-generating layer and charge-trapping layer

Triboelectric nanogenerators (TENGs) have opened a new direction in the field of flexible devices. Here, a fluorescent TENG-JNA constructed with a flexible Janus nanobelt array (JNA) and PVDF/PVP nanofibers membrane by electro-spinning is reported for the first time. The building unit of JNA is the [PANI/CNTs/PMMA]//[Tb(BA)₃phen/PMMA] Janus nanobelts, which demonstrate green fluorescence and electrical conduction bi-function, where two independent partitions are microscopically realized in the Janus nanobelts. In TENG-JNA, JNA concurrently gains excellent charge-trapping ability and charge-generating capability by optimizing the PANI content; therefore, JNA serves as both a charge-generating layer and charge-trapping layer. The interface between TB(BA)₃phen and PMMA, the existence of aromatic ring structures in the PANI main chain and the interface between PANI and PMMA are conducive to trap a large number of triboelectric charges in time to prevent the triboelectric charges from combining with induced charges, which can significantly improve the output performance of TENG-JNA. The maximum output current and voltage of TENG-JNA are 6.20 μA and 155 V, respectively. The introduction of Tb(BA)₃phen ensures the strong fluorescence of TENF-JNA, and this fluorescence can be used to judge whether TENF-JNA works normally or is out of order in a dark environment. TENG-JNA possesses other compelling features, such as prominent flexibility, good hydrophobicity, durability and light weight, which provides the premise for TENG-JNA to be used as a flexible device in a wet environment or for warning functions. The Janus nanobelt was firstly used to assemble a TENG, which provides theoretical, material and technical support for the development of new building units of TENGs and paves a pathway for designing and assembling new TENGs.

A Triboelectric Nanogenerator Based on Sodium Chloride Powder for Self-Powered Humidity Sensor

Recently, the research of distributed sensor networks based on triboelectric technology has attracted extensive attention. Here, we reported a new triboelectric nanogenerator based on sodium chloride powder (S-TENG) to obtain mechanical energy. The polytetrafluoroethylene (PTFE) film and sodium chloride powder layer serve as the triboelectric pair. After testing and calculation, the internal resistance of S-TENG is 30 MΩ, and the output power of S-TENG (size: 6 cm × 6 cm) can arrive at the maximum value (about 403.3 µW). Furthermore, the S-TENG can achieve the open circuit voltage (V_oc) of 198 V and short-circuit current (I_sc) of 6.66 µA, respectively. Moreover, owing to the moisture absorption of sodium chloride powder, the S-TENG device also has the function of the humidity sensor. This work proposed a functional TENG device, and it can promote the advancement of self-powered sensors based on the TENG devices.

Boosted output performance of nanocellulose-based triboelectric nanogenerators via device engineering and surface functionalization

Triboelectric nanogenerators (TENGs) provide promising potential to sustainably power modern portable electronic devices through harvesting mechanical energy from the environment. There is a need to further improve the sustainability credentials of TENGs by reducing the usage of non-renewable materials. Nanocellulose possessing outstanding properties, can partially replace non-renewable materials used in TENGs. Here, main sources and types of nanocellulose and methods of forming nanocellulose-based 2D/3D configurations used as triboelectric layers of TENGs are introduced. Cellulose has relatively weak tribopositivity and this review describes effective strategies of amplifying the output performance of TENGs possessing a nanocellulose-based tribopositive layer. Furthermore, efforts made to change the polarity of nanocellulose structures in order to use them as both positive and negative triboelectric layers are reviewed and their output performance is compared to that of all-synthetic polymer-based TENGs. Finally, requirements expected to be met in near future for development of commercial green nanocellulose-based TENGs are highlighted.

Multifunctional Self-Powered Electronics Based on a Reusable Low-Cost Polypropylene Fabric Triboelectric Nanogenerator

We report the development of low-cost triboelectric nanogenerators (TENGs) based on polypropylene (PP) fabrics formulated via an inexpensive melt-blowing process with an output voltage as high as 50 V. By disinfection methods such as exposure to steam, ethanol, and dry heat at 75 °C, the commercial medical masks and N95 filtering facepiece respirators (FFRs) can be reused to fabricate PP fiber based TENGs, which provide a novel regime for energy-harvesting devices based on reusable materials. As a power source, the output of one TENG can drive 15 serially connected light-emitting diodes (LEDs) or a commercial electric calculator. PP fabric TENGs can also work as self-powered sensors for the high-sensitivity detection of mechanical impact. We provide examples where the TENG is used to detect biomechanical motion such as that associated with the extension of an elbow, the touch of a finger, the impact of footsteps, and the bending of a knee without an external power supply. Most importantly, these PP fabrics for TENGs can be obtained from decontaminated medical masks that are generated as tremendous wastes every day, which provide a great potential as sustainable energy. These properties suggest that PP fabric based TENGs are promising for harvesting energy from biological systems and that they may facilitate the large-scale production of a new range of inexpensive self-powered multifunctional wearable sensors for applications in healthcare, security, and information networks.

Transparent Triboelectric Nanogenerator Based on Thermoplastic Polyurethane Films

This study aims at investigating flexible and transparent thermoplastic polyurethane (TPU) as a novel material for triboelectric nanogenerator (TENG) devices with a polyethylene terephthalate layer. Devices having TPU-either as a flat film or as electrospun micrometer-dimension fibers with varying concentrations of TPU-were tested. The best output performing device provided 21.4 V and 23 μA as open-circuit voltage and short-circuit current respectively, with the application of a small force of 0.33 N indicating the high efficiency of the device. Devices with flat films-obtained using the doctor-blade (DB) technique-have high transparency (80%) as well as high TENG output. The topography of the TPU layer, characterized by atomic force microscopy, reveals nanoscale roughness of the film surface. Finally, we demonstrate that gentle hand tapping on the TENG device can power upto 11 light-emitting diodes (LEDs). The high transparency, lightweight, simple fabrication, flexibility, and robust features of such device make it an added value for various optoelectronic applications.

Boosting the Power and Lowering the Impedance of Triboelectric Nanogenerators through Manipulating the Permittivity for Wearable Energy Harvesting

Triboelectric nanogenerators (TENGs), which hold great promise for sustainably powering wearable electronics by harvesting distributed mechanical energy, are still severely limited by their unsatisfactory power density, small capacitance, and high internal impedance. Herein, a materials optimization strategy is proposed to achieve a high performance of TENGs and to lower the matching impedance simultaneously. A permittivity-tunable electret composite film, i.e., a thermoplastic polyurethane (TPU) matrix with polyethylene glycol (PEG) additives and polytetrafluoroethylene (PTFE) nanoparticle inclusions, is employed as the triboelectric layer. Through optimizing the dielectric constant of the composite, the injected charge density and internal capacitance of the TENG are significantly enhanced, thus synergistically boosting the output power and reducing the impedance of the TENG. The optimal output power reaches 16.8 mW at an external resistance of 200 kΩ, showing a 17.3 times enhancement in output power and a 90% decline in matching impedance. This work demonstrates a significant progress toward the materials optimization of a triboelectric generator for its practical commercialization.

Triboelectric Effect Enabled Self-Powered, Point-of-Care Diagnostics: Opportunities for Developing ASSURED and REASSURED Devices

The use of rapid point-of-care (PoC) diagnostics in conjunction with physiological signal monitoring has seen tremendous progress in their availability and uptake, particularly in low- and middle-income countries (LMICs). However, to truly overcome infrastructural and resource constraints, there is an urgent need for self-powered devices which can enable on-demand and/or continuous monitoring of patients. The past decade has seen the rapid rise of triboelectric nanogenerators (TENGs) as the choice for high-efficiency energy harvesting for developing self-powered systems as well as for use as sensors. This review provides an overview of the current state of the art of such wearable sensors and end-to-end solutions for physiological and biomarker monitoring. We further discuss the current constraints and bottlenecks of these devices and systems and provide an outlook on the development of TENG-enabled PoC/monitoring devices that could eventually meet criteria formulated specifically for use in LMICs.

Electrospun PVDF-TrFE/MXene Nanofiber Mat-Based Triboelectric Nanogenerator for Smart Home Appliances

Understanding of the triboelectric charge accumulation from the view of microcapacitor formation plays a critical role in boosting the output performance of the triboelectric nanogenerator (TENG). Here, an electrospun nanofiber-based TENG (EN-TENG) using a poly(vinylidene fluoride-trifluoroethylene) (PVDF-TrFE)/MXene nanocomposite material with superior dielectric constant and high surface charge density is reported. The influence of dielectric properties on the output performance of the EN-TENG is investigated theoretically and experimentally. The fabricated EN-TENG exhibited a maximum power density of 4.02 W/m² at a matching external load resistance of 4 MΩ. The PVDF-TrFE/MXene nanocomposite improved the output performance of the EN-TENG fourfold. The EN-TENG successfully powered an electronic stopwatch and thermo-hygrometer by harvesting energy from human finger tapping. Moreover, it was utilized in smart home applications as a self-powered switch for controlling electrical home appliances, including fire alarms, fans, and smart doors. This work presents an effective and innovative approach toward self-powered systems, human-machine interfaces, and smart home applications.

Green synthesis of nano-Al2O3, recent functionalization, and fabrication of synthetic or natural polymer nanocomposites: various technological applications

Environmentally friendly fabrication of nano-Al₂O₃, recent functionalization, and preparation of polymer nanocomposites including natural and man-made polymers with various industrial applications are reviewed.

Meltblown fabric vs nanofiber membrane, which is better for fabricating personal protective equipments

The coronavirus disease 2019 (COVID-19) pandemic has led to a great demand on the personal protection products such as reusable masks. As a key raw material for masks, meltblown fabrics play an important role in rejection of aerosols. However, the electrostatic dominated aerosol rejection mechanism of meltblown fabrics prevents the mask from maintaining the desired protective effect after the static charge degradation. Herein, novel reusable masks with high aerosols rejection efficiency were fabricated by the introduction of spider-web bionic nanofiber membrane (nano cobweb-biomimetic membrane). The reuse stability of meltblown and nanofiber membrane mask was separately evaluated by infiltrating water, 75% alcohol solution, and exposing under ultraviolet (UV) light. After the water immersion test, the filtration efficiency of meltblown mask was decreased to about 79%, while the nanofiber membrane was maintained at 99%. The same phenomenon could be observed after the 75% alcohol treatment, a high filtration efficiency of 99% was maintained in nanofiber membrane, but obvious negative effect was observed in meltblown mask, which decreased to about 50%. In addition, after long-term expose under UV light, no filtration efficiency decrease was observed in nanofiber membrane, which provide a suitable way to disinfect the potential carried virus. This work successfully achieved the daily disinfection and reuse of masks, which effectively alleviate the shortage of masks during this special period.

Friction energy harvesting on bismuth tungstate catalyst for tribocatalytic degradation of organic pollutants

Mechanical energy as the green and sustainable energy source widely distributes in natural environment. In this paper, we successfully realize the conversion of mechanical energy through a friction route on the tribocatalyst of Bi₂WO₆. Under magnetic stirring, the friction between the PTFE-sealed magnetic bar and the catalyst particles resulted in the electron transfer crossing the contact interface, in which PTFE accepted the electrons and simultaneously the holes were left on the catalyst. The positively charged catalyst was demonstrated through electrostatic attraction and repulsion tests. Like photocatalytic process, the holes on the valence band of Bi₂WO₆ have strong oxidative ability that can efficiently oxidize organic pollutants. The tribocatalytic tests showed that the Bi₂WO₆ could eliminate organic dyes under magnetic stirring in dark, and we could further optimize the tribocatalytic performance via regulating the size of magnetic bar and reactor material. Finally, a high stability of tribocatalysis was revealed by the multiple tests. This work not only develops a green tribocatalysis strategy to oxidative purification of organic pollutants, but also provides a possible pathway to convert mechanical energy in environment to chemical energy, such as potential applications in environmental remediation and sustainable energy.

Triboelectric nanogenerators based on graphene oxide coated nanocomposite fibers for biomedical applications

A high demand for green and eco-friendly triboelectric nanogenerators (TENGs) has multiplied the importance of their degradability for biomedical applications. However, the charge generation of current eco-friendly TENGs is generally limited. In this research, a flexible TENG based on a silk fibroin (SF) fibrous layer and a polycaprolactone (PCL)/graphene oxide (GO) fibrous layer was developed. Moreover, the PCL/GO layer was surface modified using various concentrations of GO (0, 1.5, 3, 6, and 9 wt%). We demonstrated that surface modification using GO nanosheets significantly improved the output of the TENG. Notably, the optimized GO modified layer resulted in a voltage of 100 V, a current of 3.15 mA [Formula: see text], and a power density of 72 mW[Formula: see text]. Moreover, a thin PCL layer applied as an encapsulation layer did not significantly modulate the performance of the TENG. Furthermore, during 28 d of soaking in a phosphate buffer solution, the proposed TENG was able to successfully generate electricity. The TENG was also proposed to be used for the electrical stimulation of PC12 cells. The results confirmed that this self-powered electrical stimulator could promote the attachment and proliferation of PC12 cells. Therefore, we have shown the potential for an eco-friendly and cost-effective TENG based on GO modified PCl/GO and silk fibrous layers to be used as a power source for biomedical applications.

Polymer Materials for High-Performance Triboelectric Nanogenerators

As an emerging branch of energy conversion technologies, the triboelectric nanogenerator (TENG) pioneers a brand-new path to effectively harness varieties of mechanical energies for the purpose of powering and/or sensing. Since its invention in 2012, the TENG has experienced a booming and revolutionary development in every respect, ranging from materials synthesis and modification, architecture design to performance optimization, power management, and application exploration. In comparison to the organic solar cell and organic light-emitting diodes, TENG is a unique technique that opens the venue of using polymer materials (PMs) for harvesting mechanical energy. So far, by virtue of superior charge transfer and capturing capabilities during friction, various kinds of PMs have been developed and used as triboelectric materials in order to achieve high-performance TENGs. Here, this work focuses on the utilization and development of PMs for the TENGs technology and first gives a summary of main PMs that are frequently adopted in currently reported energy-harvesting TENGs. Second, several kinds of PMs used lately in a few novel TENGs for special or specific energy-harvesting circumstances are introduced and highlighted. Finally, the perspectives on and challenges in developing high-performance PMs toward TENGs technology are conceived and expected to be instructive to future research.

Dielectric control of porous polydimethylsiloxane elastomers with Au nanoparticles for enhancing the output performance of triboelectric nanogenerators

Taking advantage of the triboelectrification effect and electrostatic induction, triboelectric nanogenerators (TENGs) provide a simple and efficient path to convert environmental mechanical energy into electric energy. Since the generation of surface charges and their density on triboelectric materials are the key factors in determining TENG performance, many efforts have been undertaken to engineer the structures and chemistry of triboelectric materials. Among others, dielectric control of triboelectric materials is an emerging approach because the dielectric constant is intimately correlated with the capacitance of materials. In this regard, we prepared porous polydimethylsiloxane (PDMS) composites decorated with Au nanoparticles (NPs), which was designed to engineer the compressibility and dielectric constant of PDMS elastomer. To this end, a polydopamine layer was synthesized on the PDMS surface to facilitate the homogeneous deposition of Au NPs. Unlike untreated PDMS sponges, Au NPs were efficiently coated onto polydopamine-treated PDMS sponges to increase the dielectric constant. When the resulting porous NP-PDMS composites were assembled into TENG devices, the electrical output of the TENGs initially improved but decreased with the amount of Au NPs. This trade-off relationship has been discussed in terms of charge generation on the air surface and pores of NP-PDMS composites based on a recent experimental model.

Polydopamine was utilized an adhesive interface for the uniform coating of Au nanoparticles in the pores of polydimethylsiloxane to enhance the output performance of triboelectric nanogenerators.

Anti-oil-fouling hydrophobic-superoleophobic composite membranes for robust membrane distillation performance

As a promising thermally driven separation process, membrane distillation (MD) is capable of treating challenging wastewaters. However, the traditional hydrophobic membranes are vulnerable to fouling by non-polar contaminants owing to the strong hydrophobic-hydrophobic interactions. To address this problem, we developed novel anti-oil-fouling MD membranes in this study. The composite membranes with asymmetric wettability were fabricated through electrospinning polyacrylonitrile (PAN) fibrous coating on a hydrophobic polytetrafluoroethylene (PTFE) membrane, followed by hydrolyzing the PAN coating with ethylenediamine (EDA) and NaOH, respectively. These two composite membranes exhibited excellent underwater superoleophobicity, with the underwater oil contact angle >150°, which can be attributed to the fibrous and re-entrant surface structure and the optimized surface hydrophilicity of the electrospun coating. During MD process using saline and oily emulsion as feed, the composite membranes presented robust anti-oil-fouling performance, indicating by stable permeate flux and salt rejection. A novel oil-droplet adhesion force probe was introduced to quasi-quantitatively elucidate oil-membrane interaction and evaluate membrane fouling propensity, the force spectroscopy indicated that the fabricated composite membranes had fairly less attractive to crude oil compared with the PTFE membrane. Our research results suggest that the novel composite membranes with asymmetric wettability were competent to serve as an anti-oil-fouling MD membrane for desalinating challenging saline and oily wastewaters.

Electrospun Polytetrafluoroethylene Nanofibrous Membrane for High-Performance Self-Powered Sensors

Polytetrafluoroethylene (PTFE) is a fascinating electret material widely used for energy harvesting and sensing, and an enhancement in the performance could be expected by reducing its size into nanoscale because of a higher surface charge density attained. Hence, the present study demonstrates the use of nanofibrous PTFE for high-performance self-powered wearable sensors. The nanofibrous PTFE is fabricated by electrospinning with a suspension of PTFE particles in dilute polyethylene oxide (PEO) aqueous solution, followed by a thermal treatment at 350 °C to remove the PEO component from the electrospun PTFE-PEO nanofibers. The obtained PTFE nanofibrous membrane exhibits good air permeability with pressure drop comparable to face masks, excellent mechanical property with tensile strength of 3.8 MPa, and stable surface potential of - 270 V. By simply sandwiching the PTFE nanofibrous membrane into two pieces of conducting carbon clothes, a breathable, flexible, and high-performance nanogenerator (NG) device with a peak power of 56.25 μW is constructed. Remarkably, this NG device can be directly used as a wearable self-powered sensor for detecting body motion and physiological signals. Small elbow joint bending of 30°, the rhythm of respiration, and typical cardiac cycle are clearly recorded by the output waveform of the NG device. This study demonstrates the use of electrospun PTFE nanofibrous membrane for the construction of high-performance self-powered wearable sensors.

Comb-structured triboelectric nanogenerators for multi-directional energy scavenging from human movements

A triboelectric nanogenerator (TENG) is an emerging energy harvesting technology utilizing multi-directional, wasted mechanical energies stemming from vibrations, winds, waves, body movements, etc. In this study, we report a comb-structured TENG (CTENG) capable of effectively scavenging multi-directional motions from human movements, which include walking, jumping, and running. By attaching CTENG to a person's calf, we obtain a root-mean-square (RMS) power value of 5.28 μW (i.e. 13.12 V and 0.4 μA) for 1 s during mild running action (~5 m/s), which is sufficient for powering 10 light emitting diodes (LEDs). We integrate a CTENG with a simple hand-held pendulum (HHP) system with a natural frequency of 5.5 Hz. The natural frequency and input energy of our HHP system can be easily controlled by changing the holder mass and initial bending displacement, thus producing different output behaviors for the CTENG. Under the optimal HHP-based CTENG system design, the maximum output reaches 116 V at 6.5 μA under 0.1 kg mass and 4 cm bending displacement conditions. The corresponding output energy is 52.7 μJ for an operation time of 10.8 s. Our HHP-CTENG system can sufficiently power 45 LEDs and shows different output performances by varying the driving velocity of a vehicle, thus demonstrating the possibility for a self-powered velocity monitoring system.