Effects of Moisture-Based Grain Boundary Passivation on Cell Performance and Ionic Migration in Organic-Inorganic Halide Perovskite Solar Cells

Spatially selective defect management of CsPbI3 films for high-performance carbon-based inorganic perovskite solar cells

Defects formed at the surface, buried interface and grain boundaries (GB) of CsPbI3 perovskite films considerably limit photovoltaic performance. Such defects could be passivated effectively by the most prevalent post modification strategy without compromising the photoelectric properties of perovskite films, but it is still a great challenge to make this strategy comprehensive to different defects spatially distributed throughout the films. Herein, a spatially selective defect management (SSDM) strategy is developed to roundly passivate various defects at different locations within the perovskite film by a facile one-step treatment procedure using a piperazine-1,4-diium tetrafluoroborate (PZD(BF4)2) solution. The small-size PZD2+ cations could penetrate into the film interior and even make it all the way to the buried interface of CsPbI3 perovskite films, while the BF4- anions, with largely different properties from I- anions, mainly anchor on the film surface. Consequently, virtually all the defects at the surface, buried interface and grain boundaries of CsPbI3 perovskite films are effectively healed, leading to significantly improved film quality, enhanced phase stability, optimized energy level alignment and promoted carrier transport. With these films, the fabricated CsPbI3 PSCs based on carbon electrode (C-PSCs) achieve an efficiency of 18.27%, which is among the highest-reported values for inorganic C-PSCs, and stability of 500 h at 85 °C with 65% efficiency maintenance.

Cs and Br tuning to achieve ultralow-hysteresis and high-performance indoor triple cation perovskite solar cell with low-cost carbon-based electrode

With high efficacy for electron-photon conversion under low light, perovskite materials show great potential for indoor solar cell applications to power small electronics for internet of things (IoTs). To match the spectrum of an indoor LED light source, triple cation perovskite composition was varied to adjust band gap values via Cs and Br tuning. However, increased band gaps lead to morphology, phase instability, and defect issues. 10% Cs and 30% Br strike the right balance, leading to low-cost carbon-based devices with the highest power conversion efficiency (PCE) of 31.94% and good stability under low light cycles. With further improvement in device stack and size, functional solar cells with the ultralow hysteresis index (HI) of 0.1 and the highest PCE of 30.09% with an active area of 1 cm2 can be achieved. A module from connecting two such cells in series can simultaneously power humidity and temperature sensors under 1000 lux.

Identification the Role of Grain Boundaries in Polycrystalline Photovoltaics via Advanced Atomic Force Microscope

Atomicforce microscopy (AFM)-based scanning probing techniques, including Kelvinprobe force microscopy (KPFM) and conductive atomic force microscopy (C-AFM), have been widely applied to investigate thelocal electromagnetic, physical, or molecular characteristics of functional materials on a microscopic scale. The microscopic inhomogeneities of the electronic properties of polycrystalline photovoltaic materials can be examined by these advanced AFM techniques, which bridge the local properties of materials to overall device performance and guide the optimization of the photovoltaic devices. In this review, the critical roles of local optoelectronic heterogeneities, especially at grain interiors (GIs) and grain boundaries (GBs) of polycrystalline photovoltaic materials, including versatile polycrystalline silicon, inorganic compound materials, and emerging halide perovskites, studied by KPFM and C-AFM, are systematically identified. How the band alignment and electrical properties of GIs and GBs affect the carrier transport behavior are discussed from the respective of photovoltaic research. Further exploiting the potential of such AFM-based techniques upon a summary of their up-to-date applications in polycrystalline photovoltaic materials is beneficial to acomprehensive understanding of the design and manipulation principles of thenovel solar cells and facilitating the development of the next-generation photovoltaics and optoelectronics.

Comprehensive review of environmental factors influencing the performance of photovoltaic panels: Concern over emissions at various phases throughout the lifecycle

Recently, solar photovoltaic (PV) technology has shown tremendous growth among all renewable energy sectors. The attractiveness of a PV system depends deeply of the module and it is primarily determined by its performance. The quantity of electricity and power generated by a PV cell is contingent upon a number of parameters that can be intrinsic to the PV system itself, external or environmental. Thus, to improve the PV panel performance and lifetime, it is crucial to recognize the main parameters that directly influence the module during its operational lifetime. Among these parameters there are numerous factors that positively impact a PV system including the temperature of the solar panel, humidity, wind speed, amount of light, altitude and barometric pressure. On the other hand, the module can be exposed to simultaneous environmental stresses such as dust accumulation, shading and pollution factors. All these factors can gradually decrease the performance of the PV panel. This review not only provides the factors impacting PV panel's performance but also discusses the degradation and failure parameters that can usually affect the PV technology. The major points include: 1) Total quantity of energy extracted from a photovoltaic module is impacted on a daily, quarterly, seasonal, and yearly scale by the amount of dust formed on the surface of the module. 2) Climatic conditions as high temperatures and relative humidity affect the operation of solar cells by more than 70% and lead to a considerable decrease in solar cells efficiency. 3) The PV module current can be affected by soft shading while the voltage does not vary. In the case of hard shadowing, the performance of the photovoltaic module is determined by whether some or all of the cells of the module are shaded. 4) Compared to more traditional forms of energy production, PV systems offer a significant number of advantages to the environment. Nevertheless, these systems can procure greenhouse gas emissions, especially during the production stages. In conclusion, this study underlines the importance of considering multiple parameters while evaluating the performance of photovoltaic modules. Environmental factors can have a major impact on the performance of a PV system. It is critical to consider these factors, as well as intrinsic and other intermediate factors, to optimize the performance of solar energy systems. In addition, continuous monitoring and maintenance of PV systems is essential to ensure maximum efficiency and performance.

Synchronous Modulation of Energy Level Gradient and Defects for High-Efficiency HTL-Free Carbon-Based All-Inorganic Perovskite Solar Cells

In order to improve the thermal stability of perovskite solar cells (PSCs) and reduce production costs, hole transport layer (HTL)-free carbon-based CsPbI₃ PSCs (C-PSCs) have attracted the attention of researchers. However, the power conversion efficiency (PCE) of HTL-free CsPbI₃ C-PSCs is still lower than that of PSCs with HTL/ metal electrodes. This is because the direct contact between the carbon electrode and the perovskite layer has a higher requirement on the crystal quality of perovskite layer and matched energy level at perovskite/carbon interface. Herein, the acyl chloride group and its derivative trichloroacetyl chloride are used to passivate CsPbI₃ C-PSCs for the first time. The results show that the carbonyl group of trichloroacetyl chloride can effectively passivate the uncoordinated Pb²⁺ ions in perovskite. At the same time, leaving group Cl^- ions can increase the grain size of perovskite and improve the crystallization quality of perovskite layer. In addition, the trichloroacetyl chloride tends to generate cesium chloride acetate, which acts as an electron blocking layer, reduces charge recombination, promotes gradient energy level arrangement, and effectively improves the separation and extraction ability of carriers. The PCE of CsPbI₃ HTL-free C-PSCs is successfully increased from 13.40% to 14.82%.

Halide perovskite photoelectric artificial synapses: materials, devices, and applications

In recent years, there has been a research boom on halide perovskites (HPs) whose outstanding performance in photovoltaic and optoelectronic fields is obvious to all. In particular, HP materials find application in the development of artificial synapses. HP-based synapses have great potential for artificial neuromorphic systems, which is due to their outstanding optoelectronic properties, femtojoule-level energy consumption, and simple fabrication process. In this review, we present the physical properties of HPs and describe two types of synaptic devices including two-terminal (2T) memristors and three-terminal (3T) transistors. The HP layer in 2T memristors can realize the change in the device conductance through physical mechanisms dominated by ion migration. On the other hand, HPs in 3T transistors can be used as efficient light-absorbing layers and rely on some special device structures to provide reliable current changes. In the final section of the article, we discuss some of the existing applications of HP-based synapses and bottlenecks to be solved.

Atomic-Scale Imaging and Nano-Scale Mapping of Cubic α-CsPbI3 Perovskite Nanocrystals for Inverted Perovskite Solar Cells

Colloidal synthesized cubic α-CsPbI₃ perovskite nanocrystals having a smaller lattice constant (a = 6.2315 Å) compared to the standard structure, and nanoscale mapping of their surfaces are reported to achieve superior photovoltaic performance under 45-55% humidity conditions. Atomic scale transmission electron microscopic images have been utilized to probe the precise arrangement of Cs, Pb, and I atoms in a unit cell of α-CsPbI₃ NCs, which is well supported by the VESTA structure. Theoretical calculation using density functional theory of our experimental structure reveals the realization of direct band to band transition with a lower band gap, a higher absorption coefficient, and stronger covalent bonding between the Pb and I atoms in the [PbI₆]^4- octahedral, as compared to reported standard structure. Nanoscale surface mapping using Kelvin probe force microscopy yielding contact potential difference (CPD) and conductive atomic force microscopy for current mapping have been employed on α-CsPbI₃ NCs films deposited on different DMSO doped PEDOT:PSS layers. The difference of CPD value under dark and light illumination suggests that the hole injection strongly depends on the interfaces with PEDOT:PSS layer. The carrier transport through grain interiors and grain boundaries in α-CsPbI₃ probed by the single-point c-AFM measurements reveal the excellent photosensitivity under the light conditions. Finally, inverted perovskite solar cells, employing α-CsPbI₃ NCs film as an absorber layer and PEDOT:PSS layer as a hole transport layer, have been optimized to achieve the highest power conversion efficiency of 10.6%, showing their potential for future earth abundant, low cost, and air stable inverted perovskite photovoltaic devices.

Stable Perovskite Solar Cells with Bulk-Mixed Electron Transport Layer by Multifunctional Defect Passivation

Multifarious electron transport layers (ETLs), especially fullerene derivatives, have been applied in organic-inorganic hybrid perovskite (OIHP) devices owing to their superior optoelectronic properties. However, a PCBM Lewis acid molecule can only passivate the iodine-rich defect sites, which cannot solve the problem of uncoordinated Pb²⁺ and water oxygen erosion due to the high volatility of halide I^- and the hydrophilicity of organic cation MA⁺. Herein, we introduce a Lewis base, TBA-Azo with an electron-donating Azo moiety, and hydrophobic long alkyl chains into the PCBM layer to form a multifunctional bulk-mixed electron transport layer (MBE). PCBM of MBE can combine with iodine-rich trap sites at the surface and grain boundaries of perovskite. TBA-Azo molecules of MBE can passivate uncoordinated Pb²⁺ by forming Lewis adducts and isolate water/oxygen at the perovskite surface with hydrophobic alkyl chains. It results in a decrease of trap densities with 1 order of magnitude, effectively inhibiting both bimolecular and trap-induced recombination and thus elongating the carrier lifetime. The passivation of MBE can effectively improve the open-circuit voltage from 1.05 to 1.10 V. Furthermore, three long carbon chain structures of TBA-Azo in MBE can improve the water-resistant ability of OIHP devices, which can maintain 90% of the original PCE after 500 h at the humidity of 50 ± 10%. We believe that the MBE with multifunctional defect passivation provides a strategy for simultaneously achieving high-performance and high-stability OIHP optoelectronic devices.

Dual Passivation of Perovskite and SnO2 for High-Efficiency MAPbI3 Perovskite Solar Cells

So far, most techniques for modifying perovskite solar cells (PSCs) focus on either the perovskite or electron transport layer (ETL). For the sake of comprehensively improving device performance, a dual-functional method of simultaneously passivating trap defects in both the perovskite and ETL films is proposed that utilizes guidable transfer of Eu3+ in SnO2 to perovskite. Europium ions are distributed throughout the SnO2 film during the formation process of SnO2, and they can diffuse directionally through the SnO2/perovskite interface into the perovskite, while most of the europium ions remain at the interface. Under the synergistic effect of distributed Eu3+ in the SnO2 and aggregated Eu3+ at the interface, the electron mobilities of ETLs are evidently improved. Meanwhile, diffused Eu3+ ions passivate the perovskite to reduce trap densities at the grain boundaries, which can dramatically elevate the open-circuit voltage (V oc) of PSCs. Finally, the mainly PSCs coated on SnO2:Eu3+ ETL achieve a power conversion efficiency of 20.14%. Moreover, an unsealed device degrades by only 13% after exposure to ambient atmosphere for 84 days.

On the Current-Voltage Hysteresis in Perovskite Solar Cells: Dependence on Perovskite Composition and Methods to Remove Hysteresis

Current-density-voltage (J-V) hysteresis in perovskite solar cells (PSCs) is a critical issue because it is related to power conversion efficiency and stability. Although parameters affecting the hysteresis have been already reported and reviewed, little investigation is reported on scan-direction-dependent J-V curves depending on perovskite composition. This review investigates J-V hysteric behaviors depending on perovskite composition in normal mesoscopic and planar structure. In addition, methodologies toward hysteresis-free PSCs are proposed. There is a specific trend in hysteresis in terms of J-V curve shape depending on composition. Ion migration combined with nonradiative recombination near interfaces plays a critical role in generating hysteresis. Interfacial engineering is found to be an effective method to reduce the hysteresis; however, bulk defect engineering is the most promising method to remove the hysteresis. Among the studied methods, KI doping is proved to be a universal approach toward hysteresis-free PSCs regardless of perovskite composition. It is proposed from the current studies that engineering of perovskite film near the electron transporting layer (ETL) and the hole transporting layer (HTL) is of vital importance for achieving hysteresis-free PSCs and extremely high efficiency.

Accurate Investigation on the Fluorescence Resonance Energy Transfer between Single Organic Molecules and Monolayer WSe2 by Quantum Coherent Modulation-Enhanced Single-Molecule Imaging Microscopy

Hybrid organic two-dimensional (2D) materials heterostructures are attracting tremendous attention for optoelectronic applications due to their low-cost processing and complementary advantages. However, accurate understanding of the fundamental physics on the interface of the hybrid heterostructures at the single-molecule level remains largely unexplored. Here, we investigated the fluorescence resonance energy transfer (FRET) between the single organic molecules and monolayer WSe₂ through a newly developed single molecule microscopy technique, quantum coherent modulation-enhanced single-molecule imaging microscopy (QCME-SMIM). It is shown that the extremely weak energy transfer signal was successfully extracted from the huge fluorescence background, originating from the emission of monolayer WSe₂. The observed energy transfer efficiency is in agreement with a d^-4 distance dependence, with a Förster radius of ∼6 nm for the hybrid structures. Our work not only provides valuable insight into the FRET process at the single-molecule level across such hybrid organic-2D interfaces, but also demonstrates the feasibility of the newly developed technique for investigating the fundamental physics of electron transfer kinetics.