Surface Micro-/Nanotextured Hybrid PEDOT:PSS-Silicon Photovoltaic Cells Employing Kirigami Graphene

A novel molecularly imprinted electrochemical sensor from poly (3, 4-ethylenedioxythiophene)/chitosan for selective and sensitive detection of levofloxacin

The improper usage of levofloxacin (LEV) endangers both environmental safety and human public health. Therefore, trace analysis and detection of LEV have extraordinary significance. In this paper, a novel molecularly imprinted polymer (MIP) electrochemical sensor was developed for the specific determination of LEV by electrochemical polymerization of o-phenylenediamine (o-PD) using poly(3,4-ethylenedioxythiophene)/chitosan (PEDOT/CS) with a porous structure and rich functional groups as a carrier and LEV as a template molecule. The morphology, structure and properties of the modified materials were analyzed and studied. The result showed that the electron transfer rate and the electroactive strength of the electrode surface are greatly improved by the interconnection of PEDOT and CS. Meanwhile, PEDOT/CS was assembled by imprinting with o-PD through non-covalent bonding, which offered more specific recognition sites and a larger surface area for the detection of LEV and effectively attracted LEV through intermolecular association. Under the optimized conditions, MIP/PEDOT/CS/GCE showed good detection performance for LEV in a wide linear range of 0.0019- 1000 μM, with a limit of detection (LOD, S/N = 3) of 0.4 nM. Furthermore, the sensor has good stability and selectivity, and exhibits excellent capabilities in the microanalysis of various real samples.

Materials for Implantable Surface Electrode Arrays: Current Status and Future Directions

Surface electrode arrays are mainly fabricated from rigid or elastic materials, and precisely manipulated ductile metal films, which offer limited stretchability. However, the living tissues to which they are applied are nonlinear viscoelastic materials, which can undergo significant mechanical deformation in dynamic biological environments. Further, the same arrays and compositions are often repurposed for vastly different tissues rather than optimizing the materials and mechanical properties of the implant for the target application. By first characterizing the desired biological environment, and then designing a technology for a particular organ, surface electrode arrays may be more conformable, and offer better interfaces to tissues while causing less damage. Here, the various materials used in each component of a surface electrode array are first reviewed, and then electrically active implants in three specific biological systems, the nervous system, the muscular system, and skin, are described. Finally, the fabrication of next-generation surface arrays that overcome current limitations is discussed.

Synthesis of a grape-like conductive carbon black/Ag hybrid as the conductive filler for soft silicone rubber

Conductive silicone rubber (CSR) is an outstanding stretchable conductive composite due to its excellent mechanical properties and stable conductivity. In this paper, silver nanoparticles were deposited on carbon black (CB) through a reduction reaction. The uniform dispersion of silver particles on the surface of CB as well as the grape-like branch structure of hybrid particles was formed by the condensation reaction of the hydroxyl groups of CB with (3-mercaptopropyl) trimethoxysilane (KH-590), along with the interattraction between sulfhydryl groups of KH-590 and silver ions. This sulfhydryl modified conductive carbon black/Ag hybrid filler (SMCB@Ag) avoided the high processing viscosity of CSR caused by the hydroxyl groups of CB. The percolation threshold of CSR made from SMCB@Ag was 5.5 wt% according to the percolation equation. With the addition amount of SMCB@Ag increasing to 10 wt%, the conductivity of CSR increased from 10^-5 to about 10¹. Moreover, the conductivity of this CSR showed excellent stability with extension of storage time and increase of stretching-recovery cycles.

Solar Cell Based on Hybrid Structural SiNW/Poly(3,4 ethylenedioxythiophene): Poly(styrenesulfonate)/Graphene

Solar energy is considered as a potential alternative energy source. The solar cell is classified into three main types: i) solar cells based on bulk silicon materials (monocrystalline, polycrystalline), ii) thin-film solar cells (CIGS, CdTe, DSSC, etc.), and iii) solar cells based on nanostructures and nanomaterials. Nowadays, commercial solar cells are usually made by bulk silicon material, which requires not only high fabrication costs but also limited performance. In this study, the fabrication of high-performance solar cells based on hybrid structure of silicon nanowires/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/graphene (SiNW/PEDOT:PSS/Gr) is focused upon. SiNWs with different lengths of 125, 400, 800 nm, and 2 µm are fabricated by a metal-assisted chemical etching method, and their influence on the performance of the hybrid solar cells is studied and investigated. The experimental results indicate that the suitable SiNW length for the fabrication of the hybrid solar cells is about 400 nm and the best power conversion efficiency obtained is about 9.05%, which is about 2.1 times higher than that of the planar Si solar cell.

Design of Silicon Nanowire Array for PEDOT:PSS-Silicon Nanowire-Based Hybrid Solar Cell

Among various photovoltaic devices, the poly 3, 4-ethylenedioxythiophene:poly styrenesulfonate (PEDOT:PSS) and silicon nanowire (SiNW)-based hybrid solar cell is getting momentum for the next generation solar cell. Although, the power-conversion efficiency of the PEDOT:PSS–SiNW hybrid solar cell has already been reported above 13% by many researchers, it is still at a primitive stage and requires comprehensive research and developments. When SiNWs interact with conjugate polymer PEDOT:PSS, the various aspects of SiNW array are required to optimize for high efficiency hybrid solar cell. Therefore, the designing of silicon nanowire (SiNW) array is a crucial aspect for an efficient PEDOT:PSS–SiNW hybrid solar cell, where PEDOT:PSS plays a role as a conductor with an transparent optical window just-like as metal-semiconductor Schottky solar cell. This short review mainly focuses on the current research trends for the general, electrical, optical and photovoltaic design issues associated with SiNW array for PEDOT:PSS–SiNW hybrid solar cells. The foremost features including the morphology, surface traps, doping of SiNW, which limit the efficiency of the PEDOT:PSS–SiNW hybrid solar cell, will be addressed and reviewed. Finally, the SiNW design issues for boosting up the fill-factor, short-circuit current and open-circuit voltage will be highlighted and discussed.

Tailoring the Vertical Morphology of Organic Films for Efficient Planar-Si/Organic Hybrid Solar Cells by Facile Nonpolar Solvent Treatment

The optical and electrical properties of the blending organic film poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) are strongly affected by its morphology, resulting in the performance variation in Si/organic hybrid solar cells. Here, a facile postsolvent treatment is used to tailor the vertical morphology of PEDOT:PSS by introducing a nonpolar solvent. X-ray photoelectron spectroscopy depth-profiling measurements show that the distribution of PEDOT and PSS on the surface of n-type Si can be changed by nonpolar solvent n-hexane (NHX) treatment, where more PSS aggregate at the bottom of the blend film and more PEDOT float up to the top, as compared with the reference sample. As a result, after NHX treatment, the average lifetime of the Si/organic films is increased from 152 μs for untreated samples to 248 μs for NHX-treated ones because of the better passivation effect of PSS on Si. Moreover, the transmission line model measurements indicate that the contact resistance (R_C) of PEDOT:PSS film and the Ag electrode is decreased for better charge collection after NHX treatment. Eventually, the best power conversion efficiency (PCE) of 13.78% for NHX-treated planar solar cells is obtained, much higher than the PCE (with best of 12.78%) of reference devices without nonpolar solvent treatment. Our results provide a facile method to tailor the vertical morphology of the PEDOT:PSS in Si/organic hybrid solar cells.