Controlling the Distribution of Perfluorinated Sulfonic Acid Ionomer with Elastin-like Polypeptide

Unravel-engineer-design: a three-pronged approach to advance ionomer performance at interfaces in proton exchange membrane fuel cells

Proton exchange membrane fuel cells (PEMFCs), which use hydrogen as fuel, present an eco-friendly alternative to internal combustion engines (ICEs) for powering low-to-heavy-duty vehicles and various devices. Despite their promise, PEMFCs must meet strict cost, performance, and durability standards to reach their full potential. A key challenge lies in optimizing the electrode, where a thin ionomer layer is responsible for proton conduction and binding catalyst particles to the electrode. Enhancing ion transport within these sub-μm thick films is critical to improving the oxygen reduction reaction (ORR) at the cathodes of PEMFCs. For the past 15 years, our research has targeted this limitation through a comprehensive "Unravel - Engineer - Design" approach. We first unraveled the behavior of ionomers, gaining deeper insights into both the average and distributed proton conduction properties within sub-μm thick films and at interfaces that mimic catalyst binder layers. Next, we engineered ionomer-substrate interfaces to gain control over interfacial makeup and boost proton conductivity, essential for PEMFC efficiency. Finally, we designed novel nature-derived or nature-inspired, fluorine-free ionomers to tackle the ion transport limitations seen in state-of-the-art ionomers under thin-film confinement. Some of these ionomers even pave the way to address cost and sustainability challenges in PEMFC materials. This feature article highlights our contributions and their importance in advancing PEMFCs and other sustainable energy conversion and storage technologies.

Materials Strategies Tackling Interfacial Issues in Catalyst Layers of Proton Exchange Membrane Fuel Cells

The most critical challenge for the large-scale commercialization of proton exchange membrane fuel cells (PEMFCs), one of the primary hydrogen energy technologies, is to achieve decent output performance with low usage of platinum (Pt). Currently, the performance of PEMFCs is largely limited by two issues at the catalyst/ionomer interface, specifically, the poisoning of active sites of Pt by sulfonate groups and the extremely sluggish local oxygen transport toward Pt. In the past few years, emerging strategies are derived to tackle these interface problems through materials optimization and innovation. This perspective summarizes the latest advances in this regard, and in the meantime unveils the molecule-level mechanisms behind the materials modulation of interfacial structures. This paper starts with a brief introduction of processes and structures of catalyst/ionomer interfaces, which is followed by a detailed review of progresses in key materials toward interface optimization, including catalysts, ionomers, and additives, with particular emphasis on the role of materials structure in regulating the intermolecular interactions. Finally, the challenges for the application of the established materials and research directions to broaden the material library are highlighted.

Grafting of short elastin-like peptides using an electric field

Surface-grafted elastin has found a wide range of uses such as sensing, tissue engineering and capture/release applications because of its ability to undergo stimuli-responsive phase transition. While various methods exist to control surface grafting in general, it is still difficult to control orientation as attachment occurs. This study investigates using an electric field as a new approach to control the surface-grafting of short elastin-like polypeptide (ELP). Characterization of ELP grafting to gold via quartz crystal microbalance with dissipation, atomic force microscopy and temperature ramping experiments revealed that the charge/hydrophobicity of the peptides, rearrangement kinetics and an applied electric field impacted the grafted morphology of ELP. Specifically, an ELP with a negative charge on the opposite end of the surface-binding moiety assembled in a more upright orientation, and a sufficient electric field pushed the charge away from the surface compared to when the same peptide was assembled in no electric field. In addition, this study demonstrated that assembling charged ELP in an applied electric field impacts transition behavior. Overall, this study reveals new strategies for achieving desirable and predictable surface properties of surface-bound ELP.

A Two-Phase Model for Adsorption from Solution Using Quartz Crystal Microbalance with Dissipation

Quartz crystal microbalance with dissipation (QCM-D) conveniently monitors mass and mechanical property changes of thin films on solid substrates with exquisite resolution. QCM-D is frequently used to measure dissolved solute/sol adsorption isotherms and kinetics. Unfortunately, currently available methodologies to interpret QCM-D data treat the adlayer as a homogeneous medium, which does not adequately describe solution-adsorption physics. Tethering of the adsorbate to the solid surface is not explicitly recognized, and the liquid solvent is included in the adsorbate mass, which is especially in error for low coverages. Consequently, the areal mass of adsorbate (i.e., solute adsorption) is overestimated. Further, friction is not considered between the bound adsorbate and the free solvent flowing in the adlayer. To overcome these deficiencies, we develop a two-phase (2P) continuum model that self-consistently determines adsorbate and liquid-solvent contributions and includes friction between the attached adsorbate and flowing liquid solvent. We then compare the proposed 2P model to those of Sauerbrey for a rigid adlayer and Voinova et al. for a viscoelastic-liquid adlayer. Effects of 2P-adlayer properties are examined on QCM-D-measured frequency and dissipation shifts, including adsorbate volume fraction and elasticity, adlayer thickness, and overtone number, thereby guiding data interpretation. We demonstrate that distinguishing between adsorbate adsorption and homogeneous-film adsorption is critical; failing to do so leads to incorrect adlayer mass and physical properties.

Self-Assembly and Rearrangement of a Polyproline II Helix Peptide on Gold

Polyproline peptide sequences have gained popularity as anchors for peptide-based self-assembled monolayers (SAMs) due to their attractive properties. In this work, peptides containing the polyproline II helix (PPII) conformation were designed and assembled on gold (Au). A quartz crystal microbalance with dissipation was used to characterize SAM formation kinetics and related properties. Peptides were designed with the sequence (GPPPPPG)₂C. It was discovered that a biexponential adsorption and rearrangement model describes the binding kinetics of the PPII-containing peptide on Au. In this model, an initial reversible binding step is followed by an irreversible rearrangement step, given by parameter k_t. This study found k_t to be approximately 0.00064 s^-1 for the PPII-containing peptides. Similarly, we found that the adsorption of the PPII-containing peptide on Au, given by ΔG_ads, was thermodynamically favorable (-7.8 kcal mol^-1) and comparable to other common thiol terminated SAMs on Au. Furthermore, we characterized SAM properties via QCM-D, Fourier-transform infrared (FTIR) spectroscopy, and electrochemical techniques to reveal high molecular density SAMs consisting of PPII helices. In addition, these SAMs were found to have high antifouling properties. Overall, this study characterizes the fundamental assembly mechanisms, particularly, rearrangement of PPII-containing peptides for the first time, which will be useful in the designing of future peptide-based SAMs with high surface coverage and antifouling properties.

Progress on highly proton-conductive polymer thin films with organized structure and molecularly oriented structure

Several current topics are introduced in this review, with particular attention to highly proton-conductive polymer thin films with organized structure and molecularly oriented structure. Organized structure and molecularly oriented structure are anticipated as more promising approaches than conventional less-molecular-ordered structure to elucidate mechanisms of high proton conduction and control proton conduction. This review introduces related polymer materials and molecular design using lyotropic liquid crystals and hydrogen bond networks for high proton conduction. It also outlines the use of substrate surfaces and external fields, such as pressure and centrifugal force, for organizing structures and molecularly oriented structures.