Direct Inkjet Printing of Aqueous Inks to Flexible All-Solid-State Graphene Hybrid Micro-Supercapacitors

Inkjet-printed flexible V2CTx film electrodes with excellent photoelectric properties and high capacities for energy storage device

Energy storage devices are progressively advancing in the light-weight, flexible, and wearable direction. Ti3C2Tx flexible film electrodes fabricated via a non-contact, cost-effective, high-efficiency, and large-scale inkjet printing technology were capable of satisfying these demands in our previous report. However, other MXenes that can be employed in flexible energy storage devices remain undiscovered. Herein, flexible V2CTx film electrodes (with the low formula weight vs Ti3C2Tx film electrodes) with both high capacities and excellent photoelectric properties were first fabricated. The area capacitances of V2CTx film electrodes reached 531.3-5787.0 μF⋅cm-2 at 5 mV⋅s-1, corresponding to the figure of merits (FoMs) of 0.07-0.15. Noteworthy, V2CTx film electrode exhibited excellent cyclic stability with the capacitance retention of 83 % after 7,000 consecutive charge-discharge cycles. Furthermore, flexible all solid-state symmetric V2CTx supercapacitor was assembled with the area capacitance of 23.4 μF⋅cm-2 at 5 mV⋅s-1. Inkjet printing technology reaches the combination of excellent photoelectric properties and high capacities of flexible V2CTx film electrodes, which provides a new strategy for manufacturing MXene film electrodes, broadening the application prospect of flexible energy storage devices.

Highly Nanoporous Nickel Foam as Current Collectors in 3D All-Solid-State Microsupercapacitors

This study reports a streamlined method for producing a highly nanoporous current collector with a substantial specific surface area, serving as an electrode for microsupercapacitors (MSCs). Initially, commercial Ni foams are patterned into an interdigitated structure by laser cutting. Subsequently, the Ni foams are infused with NiO nanopowders through dip coating, sintering, and reduction in an H2 atmosphere, followed by the growth of MnO2 through a redox reaction. The incorporation of NiO within this three-dimensional Ni current collector results in notable porosity within the range of approximately 200-600 nm. Such a 3D, highly nanoporous electrode dramatically increases the specific surface area by 30 times and substantially boosts the amount of active material deposition, surpassing those of commercially available Ni foams. Performance evaluations of this highly nanoporous electrode in a 1 M KOH solution demonstrate an areal capacity of 19.3 F/cm2, retaining more than 95% capacitance at 5 mA/cm2, and exhibiting an energy density of 671 μW h/cm2, 25 times greater than commercial Ni foams. Moreover, in the realm of solid-state applications for MSCs, the remarkably high porous electrode achieves a commendable areal capacity of 7.22 F/cm2 and an energy density of 263.9 μW h/cm2, rendering it exceptionally suitable for use in MSC applications.

Electrochemical detection of nitrofurazone using laser-engraved three-electrode graphene array

BACKGROUND

Nitrofurazone (NFZ) is a widely-used antimicrobial agent in aquaculture. The NFZ residue can be transmitted to humans through the food chain, and cause adverse health effects including carcinogenesis and teratogenesis. Until now, a number of modified electrodes have been developed for NFZ detection, however, there are some issues that need to be improved. For example, the reported detection sensitivity is relatively low, the modification procedure is complicated, and conventional three-electrode system is used. Therefore, it is quite important to develop new NFZ detection method with higher sensitivity, simplicity and practicality.

RESULTS

Herein, a kind of integrated three-electrode array consisted with porous graphene is easily prepared through laser engraving of commercial polyimide tape. Five kinds of graphene arrays were prepared at different laser power percentage (i.e. 30 %, 40 %, 50 %, 60 % and 70 %). It is found that their structure, morphology, fluffiness and porosity show great difference, consequently affecting the electrochemical performance of graphene arrays such as conductivity, active area and electron transfer ability. The engraved graphene array at 50 % laser power percentage (LIG-50 array) is superior owing to uniform 3D structure, abundant pores and high stability. More importantly, LIG-50 array is more active for NFZ oxidation, and significantly enhances the detection sensitivity. The linear range of LIG-50 sensor is from 0.2 to 8 μM, and the detection limit is 0.035 μM, which is successfully used in fish meat samples.

SIGNIFICANCE

A sensitive, portable and practical electrochemical sensor has been successfully developed for NFZ using laser-engraved graphene array. The demonstration using fish meat samples manifests this new sensor has good accuracy and great potential in application. This study could provide a new possibility for the design and fabrication of other high-performance electrochemical sensor for various applications in the future.

Ink-based additive manufacturing for electrochemical applications

Additive manufacturing (AM), commonly known as three-dimensional (3D) printing, has drawn substantial attention in recent decades due to its efficiency and precise control in part fabrication. The limitations of conventional fabrication processes, especially regarding geometry complexity, supply chain, and environmental impact, have prompted the exploration of diverse AM technologies in electrochemistry. Especially, three ink-based AM techniques, binder jet printing (BJP), direct ink writing (DIW), and Inkjet Printing (IJP), have been extensively applied by numerous research teams to produce electrodes, catalyst scaffolds, supercapacitors, batteries, etc. BJP's versatility in utilizing a wide range of materials as powder feedstock promotes its potential for various electrode and battery applications. DIW and IJP stand out for their ability to handle multi-material manufacturing tasks and deliver high printing resolution. To capture recent advancements in this field, we present a comprehensive review of the applications of BJP, DIW, and IJP techniques in fabricating electrochemical devices and components. This review intends to provide an overview of the process-structure-property relationship in electrochemical materials and components across diverse applications manufactured using AM techniques. We delve into how the significantly improved design freedom over the structure offered by these ink-based AM techniques highlights the performance of electrochemical products. Moreover, we highlight their advantages in terms of material compatibility, geometry control, and cost-effectiveness. In specific cases, we also compare the performance of electrochemical components fabricated using AM and conventional manufacturing methods. Finally, we conclude this review article by offering some insights into the future development in this research field.

MOF/graphene oxide based composites in smart supercapacitors: a comprehensive review on the electrochemical evaluation and material development for advanced energy storage devices

The surge in interest surrounding energy storage solutions, driven by the demand for electric vehicles and the global energy crisis, has spotlighted the effectiveness of carbon-based supercapacitors in meeting high-power requirements. Concurrently, metal-organic frameworks (MOFs) have gained attention as a template for their integration with graphene oxide (GO) in composite materials which have emerged as a promising avenue for developing high-power supercapacitors, elevating smart supercapacitor efficiency, cyclic stability, and durability, providing crucial insights for overcoming contemporary energy storage obstacles. The identified combination leverages the strengths of both materials, showcasing significant potential for advancing energy storage technologies in a sustainable and efficient manner. In this research, an in-depth review has been presented, in which properties, rationale and integration of MOF/GO composites have been critically examined. Various fabrication techniques have been thoroughly analyzed, emphasizing the specific attributes of MOFs, such as high surface area and modifiable porosity, in tandem with the conductive and stabilizing features of graphene oxide. Electrochemical characterizations and physicochemical mechanisms underlying MOF/GO composites have been examined, emphasizing their synergistic interaction, leading to superior electrical conductivity, mechanical robustness, and energy storage capacity. The article concludes by identifying future research directions, emphasizing sustainable production, material optimization, and integration strategies to address the persistent challenges in the field of energy storage. In essence, this research article aims to offer a concise and insightful resource for researchers engaged in overcoming the pressing energy storage issues of our time through the exploration of MOF/GO composites in smart supercapacitors.

Advances in Printed Electronic Textiles

Electronic textiles (e-textiles) have emerged as a revolutionary solution for personalized healthcare, enabling the continuous collection and communication of diverse physiological parameters when seamlessly integrated with the human body. Among various methods employed to create wearable e-textiles, printing offers unparalleled flexibility and comfort, seamlessly integrating wearables into garments. This has spurred growing research interest in printed e-textiles, due to their vast design versatility, material options, fabrication techniques, and wide-ranging applications. Here, a comprehensive overview of the crucial considerations in fabricating printed e-textiles is provided, encompassing the selection of conductive materials and substrates, as well as the essential pre- and post-treatments involved. Furthermore, the diverse printing techniques and the specific requirements are discussed, highlighting the advantages and limitations of each method. Additionally, the multitude of wearable applications made possible by printed e-textiles is explored, such as their integration as various sensors, supercapacitors, and heated garments. Finally, a forward-looking perspective is provided, discussing future prospects and emerging trends in the realm of printed wearable e-textiles. As advancements in materials science, printing technologies, and design innovation continue to unfold, the transformative potential of printed e-textiles in healthcare and beyond is poised to revolutionize the way wearable technology interacts and benefits.

Recent advances in inkjet-printing technologies for flexible/wearable electronics

The rapid development of flexible/wearable electronics requires novel fabricating strategies. Among the state-of-the-art techniques, inkjet printing has aroused considerable interest due to the possibility of large-scale fabricating flexible electronic devices with good reliability, high time efficiency, a low manufacturing cost, and so on. In this review, based on the working principle, recent advances in the inkjet printing technology in the field of flexible/wearable electronics are summarized, including flexible supercapacitors, transistors, sensors, thermoelectric generators, wearable fabric, and for radio frequency identification. In addition, some current challenges and future opportunities in this area are also addressed. We hope this review article can give positive suggestions to the researchers in the area of flexible electronics.

Optimization of uric acid detection with Au nanorod-decorated graphene oxide (GO/AuNR) using response surface methodology

A modified glassy carbon electrode (GCE) was developed based on a synthesized graphene oxide (GO) gold nanorod (AuNR) decorated composite (GO/AuNR) for sensitive electrochemical sensing of uric acid (UA). The electrochemical performance of GO/AuNR/GCE for UA detection was investigated employing the differential pulse voltammetry (DPV) technique. Central composite design (CCD) was applied to obtain the optimum composition of the GO and AuNR composite, which provide the highest possible UA oxidation peak current. The optimum composition was obtained at a GO concentration of 5 mg mL-1 and AuNR volume of 10 mL. Under the optimum conditions, GO/AuNR/GCE showed acceptable analytical performance for UA detection with good linearity (concentration range of 10-90 μM) and both a low detection limit (0.4 μM) and quantitation limit (1.0 μM). Furthermore, the proposed sensor exhibits superior stability, reproducibility, and selectivity using ascorbic acid (AA), dopamine (DA), urea, glucose, and magnesium as interferents. Finally, practical use of GO/AuNR/GCE was demonstrated by successfully determining the content of UA in human urine samples with the standard addition approach.

Recent advances and perspectives of 3D printed micro-supercapacitors: from design to smart integrated devices

3D-printed micro-supercapacitors (MSCs) have emerged as the ideal candidates for energy storage devices owing to their unique characteristics of miniaturization, structural diversity, and integration. Exploring the 3D printing technology for various materials and architectures of MSCs is key to realizing customization and optimizing the performance of 3D-printed MSCs. In this review, we summarize the latest progress in 3D-printed MSCs with regards to general printing approaches, printable materials, and rational design considerations. Specifically, several general types of 3D printing techniques (their working principles, available materials, resolutions, advantages, and disadvantages) and their applications to fabricate electrodes with different energy storage mechanisms, and various electrolytes, are summarized. We further discuss research directions in terms of integrated systems with other electronics. Finally, future perspectives on the research and development directions in this important field are further discussed.

Planar Graphene-Based Microsupercapacitors

With the development of wearable, portable, and implantable electronic devices, flexible and on-chip microsupercapacitors (MSCs) are urgently needed for miniaturized energy storage. Planar MSCs have high power density, fast charge/discharge rate, and long operating lifetime, and can adapt to future flexible, integrated, and miniaturized electronic systems for wide application foreground. Due to the high specific surface area, outstanding electrical conductivity, and excellent electron mobility, graphene shows promising advantages in planar MSCs devices, thus stimulates wide-ranging research in the last few years. Herein, the recent progress of planar graphene-based MSCs, including the intrinsic structure regulation of graphene-based electrode materials, the specific fabrication techniques, the multifunctional integration, and various applications of MSCs as flexible and on-chip energy storage is systematically summarized. The key challenges and prospects of future planar graphene-based MSCs are also discussed targeting to realize their practical applications.

Functional 2D MXene Inks for Wearable Electronics

Inks printing is an innovative and practicable technology capable of fabricating the next generation of flexible functional systems with various designs and desired architectures. As a result, inks printing is extremely attractive in the development of printed wearables, including wearable sensors, micro supercapacitor (MSC) electrodes, electromagnetic shielding, and thin-film batteries. The discovery of Ti₃C₂T_x in 2011, a 2D material known as a MXene, which is a compound composed of layered nitrides, carbides, or carbonitrides of transition metals, has attracted significant interest within the research community because of its exceptional physical and chemical properties. MXene has high metallic conductivity of transition metal carbides combined with hydrophilic behavior due to its surface terminated functional groups, all of which make it an excellent candidate for promising inks printing applications. This paper reviews recent progress in the development of 2D MXene inks, including synthesis procedures, inks formulation and performance, and printing methods. Further, the review briefly provides an overview of future guidelines for the study of this new generation of 2D materials.

Mechanistic aspects of poly(ethylene terephthalate) recycling-toward enabling high quality sustainability decisions in waste management

Since plastic waste pollution is a severe environmental concern in modern life, the demand for recycling poly(ethylene terephthalate) (PET) has increased due to its versatile applications. Taking advantage of plastic recycling methods creates the chances of minimizing overall crude oil-based materials consumption, and as a result, greenhouse gasses, specifically CO₂, will be decreased. Although many review articles have been published on plastic recycling methods from different aspects, a few review articles exist to investigate the organic reaction mechanism in plastic recycling. This review aims to describe other processes for recycling bottle waste of PET, considering the reaction mechanism. Understanding the reaction mechanism offers practical solutions toward protecting the environment against disadvantageous outgrowths rising from PET wastes. PET recycling aims to transform into a monomer/oligomer to produce new materials from plastic wastes. It is an application in various fields, including the food and beverage industry, packaging, and textile applications, to protect the environment from contamination and introduce a green demand for the near future. In this review, the chemical glycolysis process as an outstanding recycling technique for PET is also discussed, emphasizing the catalysts' performance, reaction conditions and methods, degradation agents, the kinetics of reactions, and reprocessing products. In general, a correct understanding of the PET recycling reaction mechanism leads to making the right decisions in waste management.

A seamlessly integrated device of micro-supercapacitor and wireless charging with ultrahigh energy density and capacitance

Microdevice integrating energy storage with wireless charging could create opportunities for electronics design, such as moveable charging. Herein, we report seamlessly integrated wireless charging micro-supercapacitors by taking advantage of a designed highly consistent material system that both wireless coils and electrodes are of the graphite paper. The transferring power efficiency of the wireless charging is 52.8%. Benefitting from unique circuit structure, the intact device displays low resistance and excellent voltage tolerability with a capacitance of 454.1 mF cm⁻², superior to state-of-the-art conventional planar micro-supercapacitors. Besides, a record high energy density of 463.1 μWh cm⁻² exceeds the existing metal ion hybrid micro-supercapacitors and even commercial thin film battery (350 μWh cm⁻²). After charging for 6 min, the integrated device reaches up to a power output of 45.9 mW, which can drive an electrical toy car immediately. This work brings an insight for contactless micro-electronics and flexible micro-robotics.

Miniaturized energy storage devices integrated with wireless charging bring opportunities for next generation electronics. Here, authors report seamlessly integrated wireless charging micro-supercapacitors with high energy density capable of driving a model electrical car.

Bio-inspired deposition of electrochemically exfoliated graphene layers for electrical resistance heating applications

Electrochemically exfoliated graphene (eeG) layers possess a variety of potential applications, e.g. as susceptor material for contactless induction heating in dynamic electro-magnetic fields, and as flexible and transparent electrode or resistivity heating elements. Spray coating of eeG dispersions was investigated in detail as a simple and fast method to deposit both, thin conducting layers and ring structures on polycarbonate substrates. The spray coating process was examined by systematic variation of dispersion concentration and volume applied to heated substrates. Properties of the obtained layers were characterized by UV-VIS spectroscopy, SEM and Confocal Scanning Microscopy. Electrical conductivity of eeG ring structures was measured using micro-four-point measurements. Modification of eeG with poly(dopamine) and post-thermal treatment yields in the reduction of the oxidized graphene proportion, an increase in electrical conductivity, and mechanical stabilization of the deposited thin layers. The chemical composition of modified eeG layer was analyzed via x-ray photoelectron spectroscopy pointing to the reductive behavior of poly(dopamine). Application oriented experiments demonstrate the direct electric current heating (Joule-Heating) effect of spray-coated eeG layers.

Inkjet-Printed Ultrathin MoS2-Based Electrodes for Flexible In-Plane Microsupercapacitors

Flexible and wearable energy storage microdevice systems with high performance and safety are promising candidates for the electronics of on-chip integration. Herein, we demonstrate inkjet-printed ultrathin electrodes based on molybdenum disulfide (MoS₂) nanosheets for flexible and all-solid-state in-plane microsupercapacitors (MSCs) with high capacitance. The MoS₂ nanosheets were uniformly dispersed in the low-boiling point and nontoxic solvent isopropanol to form highly concentrated inks suitable for inkjet printing. The MSCs were assembled by printing the highly concentrated MoS₂ inks on a polyimide substrate with appropriate surface tension using a simple and low-cost desktop inkjet printer. Because of the two-dimensional structure of MoS₂ nanosheets, the as-assembled planar MSCs have high loadings of active materials per unit area, resulting in more flexibility and thinness than the capacitors with a traditional sandwich structure. These planar MSCs can not only possess any collapsible shape through the computer design but also exhibit excellent electrochemical performance (with a maximum energy density of 0.215 mW h cm^-3 and a high-power energy density of 0.079 W cm^-3), outstanding mechanical flexibility (almost no degradation of capacitance at different bending radii), good cycle stability (85.6% capacitance retention even after 10,000 charge-discharge cycles), and easy scale-up. Moreover, a blue light-emitting diode can be powered using five MSCs connected in series. The in-plane and low-cost MSCs with high energy densities have great application potential for integrated energy storage systems including wearable planar solar cells and other electronics.

Inkjet-Printing Technology for Supercapacitor Application: Current State and Perspectives

Inkjet-printing (IJP) technology is recognized as a significant breakthrough in manufacturing high-performance electrochemical energy storage systems. In comparison to conventional fabrication protocols, this printing technique offers various advantages, such as contact-less high-resolution patterning capability; low-cost, controlled material deposition; process simplicity; and compatibility with a variety of substrates. Due to these outstanding merits, significant research efforts have been devoted to utilizing IJP technology in developing electrochemical energy storage devices, particularly in supercapacitors (SCs). These attempts have focused on fabricating the key components of SCs, including electrode, electrolyte, and current collector, through rational formulation and patterning of functional inks. In an attempt to further expand the material design strategy and accelerate technology development, it is urgent and essential to obtain an in-depth insight into the recent developments of inkjet-printed SCs. Toward this aim, first, a general introduction to the fundamental principles of IJP technology is provided. After that, the latest achievements in IJP of capacitive energy storage devices are systematically summarized and discussed with a particular emphasis on the design of printable functional materials, the printing process, and capacitive performance of inkjet-printed SCs. To close, existing challenges and future research trends for developing state-of-the-art inkjet-printed SCs are proposed.

3D Printing of NiCoP/Ti3C2 MXene Architectures for Energy Storage Devices with High Areal and Volumetric Energy Density

Designing high-performance electrodes via 3D printing for advanced energy storage is appealing but remains challenging. In normal cases, light-weight carbonaceous materials harnessing excellent electrical conductivity have served as electrode candidates. However, they struggle with undermined areal and volumetric energy density of supercapacitor devices, thereby greatly impeding the practical applications. Herein, we demonstrate the in situ coupling of NiCoP bimetallic phosphide and Ti₃C₂ MXene to build up heavy NCPM electrodes affording tunable mass loading throughout 3D printing technology. The resolution of prints reaches 50 μm and the thickness of device electrodes is ca. 4 mm. Thus-printed electrode possessing robust open framework synergizes favorable capacitance of NiCoP and excellent conductivity of MXene, readily achieving a high areal and volumetric capacitance of 20 F cm^-2 and 137 F cm^-3 even at a high mass loading of ~ 46.3 mg cm^-2. Accordingly, an asymmetric supercapacitor full cell assembled with 3D-printed NCPM as a positive electrode and 3D-printed activated carbon as a negative electrode harvests remarkable areal and volumetric energy density of 0.89 mWh cm^-2 and 2.2 mWh cm^-3, outperforming the most of state-of-the-art carbon-based supercapacitors. The present work is anticipated to offer a viable solution toward the customized construction of multifunctional architectures via 3D printing for high-energy-density energy storage systems.