High-Performance Salt-Rejecting and Cost-Effective Superhydrophilic Porous Monolithic Polymer Foam for Solar Steam Generation

Tree-Inspired Structurally Graded Aerogel with Synergistic Water, Salt, and Thermal Transport for High-Salinity Solar-Powered Evaporation

Solar-powered interfacial evaporation is an energy-efficient solution for water scarcity. It requires solar absorbers to facilitate upward water transport and limit the heat to the surface for efficient evaporation. Furthermore, downward salt ion transport is also desired to prevent salt accumulation. However, achieving simultaneously fast water uptake, downward salt transport, and heat localization is challenging due to highly coupled water, mass, and thermal transport. Here, we develop a structurally graded aerogel inspired by tree transport systems to collectively optimize water, salt, and thermal transport. The arched aerogel features root-like, fan-shaped microchannels for rapid water uptake and downward salt diffusion, and horizontally aligned pores near the surface for heat localization through maximizing solar absorption and minimizing conductive heat loss. These structural characteristics gave rise to consistent evaporation rates of 2.09 kg m-2 h-1 under one-sun illumination in a 3.5 wt% NaCl solution for 7 days without degradation. Even in a high-salinity solution of 20 wt% NaCl, the evaporation rates maintained stable at 1.94 kg m-2 h-1 for 8 h without salt crystal formation. This work offers a novel microstructural design to address the complex interplay of water, salt, and thermal transport.

Stable and Durable Superhydrophobic Cotton Fabrics Prepared via a Simple 1,4-Conjugate Addition Reaction for Ultrahigh Efficient Oil-Water Separation

Superhydrophobic materials used for oil-water separation have received wide attention. However, the simple and low-cost strategy for making durable superhydrophobic materials remains a major challenge. Here, this work reports that stable and durable superhydrophobic cotton fabrics can be prepared using a simple two-step impregnation process. Silica nanoparticles are surface modified by hydrolysis condensation of 3-aminopropyltrimethoxysilane (APTMS). 1,4-conjugate addition reaction between the acrylic group of cross-linking agent pentaerythritol triacrylate (PETA) and the amino group of octadecylamine (ODA) forms a covalent cross-linked rough network structure. The long hydrophobic chain of ODA makes the cotton fabric exhibit excellent superhydrophobic properties, and the water contact angle (WCA) of the fabric surface reaches 158°. The modified cotton fabric has good physical and chemical stability, self-cleaning, and anti-fouling. At the same time, the modified fabric shows excellent oil/water separation efficiency (98.16% after 20 cycles) and ultrahigh separation flux (15413.63 L m-2 h-1) due to its superhydrophobicity, superoleophilicity, and inherent porous structure. The method provides a broad prospect in the future diversification applications of oil/water separation and oil spill cleaning.

Polyhedral Oligomeric Sesquioxane Cross-Linked Chitosan-Based Multi-Effective Aerogel Preparation and Its Water-Driven Recovery Mechanism

The use of environmentally friendly and non-toxic biomass-based interfacial solar water evaporators has been widely reported as a method for water purification in recent years. However, the poor stability of the water transport layer made from biomass materials and its susceptibility to deformation when exposed to harsh environments limit its practical application. To address this issue, water-driven recovery aerogel (PCS) was prepared by cross-linking epoxy-based polyhedral oligomeric silsesquioxane (EP-POSS) epoxy groups with chitosan (CS) amino groups. The results demonstrate that PCS exhibits excellent water-driven recovery performance, regaining its original volume within a very short time (1.9 s) after strong compression (ε > 80%). Moreover, PCS has a water absorption rate of 2.67 mm s-1 and exhibits an excellent water absorption capacity of 22.09 g g-1 even after ten cycles of absorption-removal. Furthermore, a photothermal evaporator (PCH) was prepared by loading the top layer with hydrothermally reacted tannins (HAs) and Zn2+ complexes. The results indicate that PCH achieves an impressive evaporation rate of 1.89 kg m-2 h-1 under one sun illumination. Additionally, due to the antimicrobial properties of Zn2+, PCH shows inhibitory effects against Staphylococcus aureus and Escherichia coli, thereby extending the application of solar water evaporators to include antimicrobial purification in natural waters.

Recent Advances of Green Electricity Generation: Potential in Solar Interfacial Evaporation System

Solar-driven interfacial evaporation (SDIE) has played a pivotal role in optimizing water-energy utilization, reducing conventional power costs, and mitigating environmental impacts. The increasing emphasis on the synergistic cogeneration of water and green electricity through SDIE is particularly noteworthy. However, there is a gap of existing reviews that have focused on the mechanistic understanding of green power from water-electricity cogeneration (WEC) systems, the structure-activity relationship between efficiency of green energy utilization in WEC and material design in SDIE. Particularly, it lacks a comprehensive discussion to address the challenges faced in these areas along with potential solutions. Therefore, this review aims to comprehensively assess the progress and future perspective of green electricity from WEC systems by investigating the potential expansion of SDIE. First, it provides a comprehensive overview about material rational design, thermal management, and water transportation tunnels in SDIE. Then, it summarizes diverse energy sources utilized in the SDIE process, including steaming generation, photovoltaics, salinity gradient effect, temperature gradient effect, and piezoelectric effect. Subsequently, it explores factors that affect generated green electricity efficiency in WEC. Finally, this review proposes challenges and possible solution in the development of WEC.

Cost-Effective and Scalable Solar Interface Evaporators Derived from Industry Waste for Efficient Solar Steam Generation

Interfacial solar steam generation for sustainable and eco-friendly desalination and wastewater treatment has attracted much attention. However, costly raw materials and complex preparation processes pose constant challenges to its wide promotion. Herein, a novel, cost-effective, and scalable strategy is presented for preparing solar interface evaporators using industrial waste as a raw material. Modified polyethylene foam evaporators (M-EPEs) are simply prepared by drilling and then hydrophilic modification of industrial waste (EPE-1). M-EPEs not only retain the strong mechanical properties and thermal insulating properties (0.047 W·m-1·K-1) of EPE-1 but also exhibit superhydrophilicity and strong light absorption (over 90%). M-EPEs achieve a high evaporation rate of 1.497 kg·m-2·h-1 and photothermal efficiency of up to 93.8% under 1 kW·m-2 solar illumination. Moreover, it has excellent stability and salt tolerance. Our work addresses the environmental issues of recycling polyethylene waste and provides a facile and efficient strategy for designing low-cost, large-scale solar interface evaporators for desalination.

Vertical porous aerogel based on polypyrrole and bimetallic modified β-cyclodextrin polymer-chitosan for efficient solar evaporation

Solar-driven interfacial evaporation (SDIE) stands out as a prospective technology for freshwater production, playing a significant role in mitigating global water scarcity. Herein, a cyclodextrin polymer/chitosan composite aerogel (PPy-La/Al@CDP-CS) with vertically aligned channels was prepared as a solar evaporator for efficient solar steam generation. The vertically aligned pore structure, achieved through directional freezing assisted by liquid nitrogen, not only improves water transport during evaporation but also enhances light absorption through multiple reflections of sunlight within the pores. The polypyrrole particles sprayed on the surface of the aerogel acted as a light-absorbing layer, resulting in an impressive absorbance of 98.15 % under wetting conditions. The aerogel has an evaporation rate of 1.85 kg m-2 h-1 under 1 kW m-2 irradiation. Notably, the vertical pore structure of the aerogel allows it to exhibit excellent evaporation performance and salt resistance even in highly concentrated salt solutions. Furthermore, this aerogel is an excellent solar-driven interfacial evaporator for purifying seawater and fluoride-containing wastewater. This photothermal aerogel has the advantages of excellent performance, low cost, and environmental friendliness, and thus this work provides a new approach to the design and fabrication of solar photothermal materials for water treatment.

Clay-based aerogel combined with CuS for solar-driven interfacial steam generation and desalination

Solar-driven water purification is a promising technology that can effectively utilize solar energy for seawater desalination. However, poor materials are unable to meet the dense energy of solar steam generation in natural sunlight for real-time practical applications. Therefore, the demand for energy density can be increased by using improved semiconductor aerogel materials. Here, we report a simple chemical method to obtain a CuS@ATP/PS composite aerogel (named CuAP), which was made of attapulgite (ATP) and CuS loaded onto it using an N-template to give it good photothermal characteristics (CuS@ATP), and then cross-link it with potato starch (PS). The evaporation rate of CuAP-15 aerogel in pure water at 1 kW m-2 solar radiation is 1.57 kg m-2 h-1. Meanwhile, CuAP-15 aerogel showed excellent salt resistance with an evaporation rate of 1.35 kg m-2 h-1 in 20 wt% NaCl solution. And also exhibited excellent cycling durability in cycling stability tests. More importantly, the freshwater yield can reach 6.54 kg m-2 under natural light irradiation for 11 h. Therefore, CuAP aerogel has a great prospect of application in the field of seawater desalination in the future.

3D porous β-cyclodextrin grafted graphene oxide/sodium alginate superhydrophilic natural polysaccharide-based aerogel for solar steam generation

Solar steam generation (SSG) emerges as a paramount technology for efficient and sustainable desalination and wastewater purification. The innovative development of porous aerogel materials for solar steam generation heralds a new era in photothermal materials. In this study, a category of β-cyclodextrin-grafted graphene oxide/sodium anionic polysaccharide alginate composite aerogels (named GO-CD/SA) with solar steam generation behavior and wastewater purification properties is developed. GO-CD/SA demonstrates remarkable properties, including an impressive solar absorption efficiency of approximately 97.4 %, a low thermal conductivity of just 0.124 W m-1 K-1 in a wetted state, and exceptional superhydrophilicity. These attributes collectively contribute to GO-CD/SA achieving an evaporation rate of 1.79 kg m-2 h-1 when utilized with pure water. Furthermore, GO-CD/SA features an abundant three-dimensional porous structure (88.07 % porosity) and superhydrophilic properties that promote the rapid reflux of salt solution between the pore channels. This, in turn, enables excellent salt resistance, with no noticeable salt crystals precipitating during continuous evaporation in 20 % high concentration brine for 6 h. GO-CD/SA also demonstrates outstanding purification capabilities for organic dye wastewater and heavy metal ion wastewater. Therefore, this work combines the advantages of salt tolerance and wastewater treatment, paving the way for the exploration of natural polysaccharide-based photothermal materials.

3D Tea-Residue Microcrystalline Cellulose Aerogel with Aligned Channels for Solar-Driven Interfacial Evaporation Co-generation

Solar-driven interfacial evaporation co-generation (SIE-CG) technology is of great significance in solving the problem of water and energy shortage. Herein, we report the ionic liquid-assisted alignment of waste biomass tea residue-based microcrystalline cellulose for aerogels (abbreviated as TPPA-5) with aligned channels for solar-driven interfacial evaporation co-generation. In the ionic liquid, strong H-bonding is formed between the pyranoid rings of cellulose combined with the slow freezing technique, resulting in the microcrystalline cellulose being reoriented, which allowed TPPA-5 to form abundant aligned channels after solvent replacement and freeze-drying. These aligned channels enable the brine to form a localized circulating flow, which is conducive to the improvement of the TPPA's evaporation rate and salt resistance. The salinity gradient is naturally formed in the channel of TPPA, which enables TPPA-5 to show excellent power generation performance. The evaporation rate of TPPA-5 can reach 3.39 kg m-2 h-1 under 1 kW m-2. With methanol as a highly polar proton solvent, the maximum output voltage obtained was 67.534 mV due to the overlapping electric double-layer effect formed by hydrogen protons on the TPPA surface, and the energy utilization efficiency is 95.95%. Moreover, TPPA-5 can purify pesticide-containing wastewater, which has the advantages of being recyclable and environmentally friendly, showing potential application value in the field of seawater desalination and steam co-generation.

Stable polyethylene glycol/biochar composite as a cost-effective photothermal absorber for 24 hours of steam and electricity cogeneration

Seawater desalination powered by solar energy is the most environmentally and economical solution in responding to the global water and energy crisis. However, solar desalination has been negatively impacted by intermittent sun radiation that alternates between day and night. In this study, sugarcane bagasse (SCB) was recycled via the pyrolysis process to biochar as a cost-effective solar absorber. Besides, polyethylene glycol (PEG) as a phase change material was encapsulated in the abundant pore structure of biochar to store the thermal energy for 24 hours of continuous steam generation. The BDB/1.5 PEG evaporator exhibited an evaporation rate of 2.11 kg m-2 h-1 (98.1% efficiency) under 1 sun irradiation. Additionally, the BDB/1.5 PEG evaporator incorporated by the TEC1-12706 module for continuous steam and electricity generation with a power density of 320.41 mW m-2. Moreover, 10 continuous hours of evaporation were applied to the composite demonstrating outstanding stability. The composite exhibited high water purification efficiency through solar desalination due to the abundant functional groups on the biochar surface. Finally, the resulting low-cost and highly efficient PCM-based absorber can be used on a wide scale to produce fresh water and energy.

Overview of Solar Steam Devices from Materials and Structures

The global shortage of freshwater supply has become an imminent problem. The high energy consumption of traditional desalination technology cannot meet the demand for sustainable energy development. Therefore, exploring new energy sources to obtain pure water has become one of the effective ways to solve the freshwater resource crisis. In recent years, solar steam technology which utilizes solar energy as the sole input source for photothermal conversion has shown to be sustainable, low-cost, and environmentally friendly, providing a viable low-carbon solution for freshwater supply. This review summarizes the latest developments in solar steam generators. The working principle of steam technology and the types of heating systems are described. The photothermal conversion mechanisms of different materials are illustrated. Emphasis is placed on describing strategies to optimize light absorption and improve steam efficiency from material properties to structural design. Finally, challenges in the development of solar steam devices are pointed out, aiming to provide new ideas for the development of solar steam devices and alleviate the shortage of freshwater resources.

Superhydrophobic/Superhydrophilic Janus Evaporator for Extreme High Salt-Resistance Solar Desalination by an Integrated 3D Printing Method

The emerging solar desalination technology has incomparable advantages for providing a clean water solution. However, the issue of salt accumulation on the solar evaporator tops during the steam generation leads to a considerable decrease in the evaporation rate. Herein, we demonstrate a superhydrophobic/superhydrophilic Janus evaporator that enables a stable solar evaporation even in saturated brine. Our Janus solar evaporator with a superhydrophobic top and a superhydrophilic bottom has been manufactured integrally, allowing for a fast steam evaporation without the impediment of the accumulated salt residues. The superhydrophobic top changes the water passageway from the center toward the edges while it allows for the vertical transport of both solar thermo and evaporated steams. Salt residues would only be deposited at the edges of the superhydrophilic bottom, allowing for a long-term stability of the evaporator for a continuous (>50 h) solar evaporation in saturated brine, which is record-breaking for salt-resistant solar evaporators. With stable and efficient evaporation performance out of high-salinity brine, this work provides a fascinating avenue for the desalination of seawater in a salt-resistant and efficient manner.

3D carbonized grooved straw with efficient evaporation and salt resistance for solar steam generation

Solar steam generation (SSG) is considered an effective solution to the global shortage of freshwater resources. To solve the practical application challenges of SSG in remote outdoor environments where electricity is scarce, it is of great importance to developing new solar evaporators. In this study, a three-dimensional (3D) biochar solar evaporator based on carbonized grooved straw was prepared from agricultural waste corn straw, which had high solar energy conversion efficiency and excellent salt resistance. The existence of grooves increases the surface area to absorb more sunlight and makes the light multilevel reflection improve the evaporation rate. The excellent light absorption, super hydrophilic, and heat shielding properties of 3D carbonized grooved straw resulted in a good evaporation rate (1.57 kg⋅m^-2·h^-1) and energy efficiency (85.9%) under 1 sun irradiation. The 3D grooved biochar solar distiller also demonstrated efficient formation evaporation performance and excellent salt resistance in practical applications in seawater desalination and surface water purification. The 3D grooved biochar solar distiller prepared from agricultural waste has the advantages of being economical and environmentally friendly, with good application prospects.

Water Harvesting Strategies through Solar Steam Generator Systems

Solar steam generator (SSG) systems have attracted increasing attention, owing to its simple manufacturing, material abundance, cost-effectiveness, and environmentally friendly freshwater production. This system relies on photothermic materials and water absorbing substrates for a clean continuous distillation process. To optimize this process, there are factors that are needed to be considered such as selection of solar absorber and water absorbent materials, followed by micro/macro-structural system design for efficient water evaporation, floating, and filtration capability. In this contribution, we highlight the general interfacial SSG concept, review and compare recent progresses of different SSG systems, as well as discuss important factors on performance optimization. Furthermore, unaddressed challenges such as SSG's cost to performance ratio, filtration of untreatable micropollutants/microorganisms, and the need of standardization testing will be discussed to further advance future SSG studies.

High-Performance Solar Steam Generator Using Low-Cost Biomass Waste Photothermal Material and Engineering of the Structure

In this work, high-performance, low-cost, environmentally friendly multilayered solar steam generation systems are fabricated by engineering the structure and using a biomass photothermal material. Remarkably, the biomass photothermal material is extracted from the pyrolysis waste of linseed (flax) grains. The introduced system desalinates water using solar energy as the renewable source of energy, and its light absorber is from the waste of a renewable source. The biomass waste powder possesses a mesoporous structure, providing high light absorption through photon scattering and its high surface area. Moreover, to harvest the incident light efficiently and manage the thermal energy generated, devices including light absorbers with cone and cubic configurations and different water manager layers are fabricated and compared to each other. To confirm the high performance of the introduced photothermal material, different systems comprising graphite, graphene oxide, and carbon nanotube light absorbers are also fabricated. Using a biomass light absorber combined with harvesting of the light in different directions (cone configuration), the system with a water evaporation rate of 1.59 kg/m²h corresponding to an efficiency of 92.9% is achieved. Furthermore, by depositing a thin layer of the transparent thermal superinsulator silica aerogel on the light absorber layer, the generated heat is localized and the heat losses are prevented, leading to a 7.5% enhancement of the water evaporation rate of the biomass system. The eco-friendly biomass-based system shows no significant change in its performance through operation for 40 desalination cycles of Persian Gulf water.

Rapid Fabrication of Porous Photothermal Hydrogel Coating for Efficient Solar-Driven Water Purification

Cost management and scalable fabrication without sacrificing the purification performance are two critical issues that should be addressed before the practical commercial application of solar-driven evaporators. To address this challenge, we report a porous photothermal hydrogel coating prepared by mixing the raw materials of sawdust (SD), carbon nanotubes (CNTs), and poly(vinyl alcohol) (PVA), which was applied to undergo a blading-drying-rehydration process to prepare the evaporator. In the coating, the crystallized PVA gives the coating a solid skeleton and the sawdust endows the coating with a loose structure to sufficiently enhance the water transportation capacity. As a result, the evaporator coated with the hydrogel coating displays a high water transport rate and efficient evaporation performance along with excellent mechanical properties and stability. Water migrates vertically upward 5 cm within 4 minutes. The compressive stress of the rehydrated hydrogel coating reaches as high as 14.28 MPa under 80% strain. The water evaporation rate of the hydrogel coating-based evaporator reaches 1.833 kg m^-2 h^-1 corresponding to an energy efficiency of 83.29% under 1 sun irradiation. What is more, the hydrogel coating retains its excellent evaporation performance and stability after immersion in acid or alkali solution, ultrasound treatment, and long-time immersion in water. Under outdoor conditions, the water evaporation rate of the hydrogel coating-based evaporator is about 5.69 times higher than that of pure water. This study proposes a rapid, cost-effective, and scalable strategy for preparing a high-performance photothermal hydrogel coating that will find sustainable and practical application in solar-driven water purification.

A Superhydrophilic Silicon Surface Enhanced by Multiscale Hierarchical Structures Fabricated by Laser Direct Writing

Many biological surfaces with hierarchical structures exhibit super wetting properties, but a multiscale hierarchical metal surface with superhydrophilic performance is difficult to be fabricated using a simple method. In this work, we report a large area micro/nanotextured superhydrophilic silicon surface fabricated by a laser direct writing technique. The combination of a microscale column structure and randomization-distributed nano-bumps decorated on the column enhances the superhydrophilic properties, with the contact angle reduced substantially from about 46° to 0°, where the droplets are able to spread rapidly within 591 ms. The water wetting orientation can be regulated by controlling the shape of microcolumns on the surface. Moreover, our results show that the fabricated surface with the hierarchical structure has better droplet shape control performance and higher fog collection efficiency compared to a smooth surface. These surfaces have potential applications in heat exchangers, biosensors, cell adhesives, and self-cleaning solar cells.

Highly stable gold nanolayer membrane for efficient solar water evaporation under a harsh environment

Interfacial solar water evaporation has attracted tremendous attention for sunlight harvesting for water purification. However, salt formation and stability of the photothermal materials (PTMs) remain a challenge that need addressing before bringing this technology to real-world applications. In this work, a nanoscale thin film of gold (Au) on a polytetrafluoroethylene (PTFE) membrane has been prepared using a magnetic sputtering technique. The fabricated membrane displays a robust mechanical strength and chemical stability arising from the adhesiveness of the thin film Au nanolayer on the PTFE membrane as well as the chemical inertness of the noble metal PTM. The Au nanolayer/PTFE membrane with cellulose sponge substrate resulted in an evaporation rate of 0.88 kg m^-2 h^-1 under 1 sun intensity. Remarkable salt ion rejection of 99.9% has been obtained, meeting the required standard for drinking water. Moreover, the membrane exhibited excellent stability and reusability in natural seawater and high salinity brine (150 g/L) and even in severe conditions (acidic, basic, and oxidized). No noticeable salt formation was observed on the evaporator surface after the tests. These findings reveal promising prospects for using a magnetron sputtering technique to fabricate a stable photothermal membrane for seawater and high salinity brine desalination.

Research Progress on the Photo-Driven Catalytic Production of Biodiesel

Biodiesel considered a green, environmentally friendly, and renewable energy source is one of the most promising candidates to replace fossil fuels to supply energy for the world. The conventional thermocatalytic methods have been extensively explored for producing biodiesel, while inevitably encountering some drawbacks, such as harsh operating conditions and high energy consumption. The catalytic production of biodiesel under mild conditions is a research hotspot but with difficulty. Photocatalysis has recently been highlighted as an eco-friendly and energy-saving approach for biodiesel production. This mini-review summarizes typical photocatalysts for biodiesel production and discusses in detail the catalytic mechanism and strategies of the photo-driven (trans)esterification to produce biodiesel. The current challenges and future opportunities of photo-driven catalysis to prepare biodiesel are also outlined, in steps towards guiding the design of advanced photocatalysts for biodiesel production.

Magnesium hydroxide coated hollow glass microspheres/chitosan composite aerogels with excellent thermal insulation and flame retardancy

The development of an environmental-friendly thermal insulation and flame retardant material has attracted widespread attention in modern architecture. In this work, a kind of novel aerogel composites were prepared by incorporation of Mg(OH)₂ coated hollow glass microspheres (HGM) into chitosan (CSA) matrix and then cross-linking by glutaraldehyde (abbreviated as CSA-HGM-Mg(OH)₂). The as-prepared composite aerogel exhibits vertical directional channel with high porosity and excellent thermal insulation with a low thermal conductivity of 0.035 W m^-1 k^-1. Besides, it shows excellent flame retardancy with a high limit oxygen index (LOI) value up to 50.8, which is one of the highest values among the most of flame retardants reported previously. Also, a very low peak heat release rate (pHRR) of 24.12 kW m^-2 was obtained which makes the aerogel composite reaching UL-94 V-0 rating. Such results may be attributed to a synergy effect by combination of its abundantly porous structure derived from HGM to give a better thermal insulation and excellent nonflammability of CSA and Mg(OH)₂ to offer a superior flame retardancy. Taking advantages of its high mechanical strength, low cost materials, simple and scalable preparation method, CSA-HGM-Mg(OH)₂ aerogel composites may hold great potential for future thermal insulation and flame retardant applications.

Chemical treatment of biomasswastes as carbon dot carriers for solar-driven water purification

A purely chemical method is demonstrated to treat a variety of biomass wastes for extracting cellulose nanofibrils (CNFs) with a consistent property. By hydrothermal reaction, carbon dots (CDs) can be easily grafted on the surface of CNFs to act as photo-thermal agents and enable fast water evaporation rate at 2.5 kg m^-2h^-1 with about 96.45% solar-to-vapor efficiency under one sun irradiation. This derives from good hydration ability of this system, which lowers the evaporation enthalpy. Moreover, this system not only adsorbs dye contaminants effectively by the formation of hydrogen bonds, but also possesses long-term antifouling solar desalination by means of rationally drilled millimeter-sized channels. Given the sustainable biomass resources and scalable fabrication process, this work offers a promising strategy towards construct low-cost evaporators with the excellent water purification performance.

Coffee Grounds-Doped Alginate Porous Materials for Efficient Solar Steam Generation

Solar steam generation (SSG) devices have emerged as one of the promising technologies for seawater desalination to meet the worldwide demand for clean water. Herein, we fabricated a new monolithic SSG system derived from waste coffee grounds (CG) through a simple carbonization followed by a freeze-drying process (named as CCGA). The as-prepared CCGA possesses a porous structure with superhydrophilic, abundant porosity (81.7%); low thermal conductivity (0.129 W m^-1 K^-1) in a wet state; low apparent density (25 mg cm^-3); and broad sunlight absorption in a wet state (ca. 93%). The combination of its carbon nature and abundant porous structure endowed barrier-free water transmission channels, a self-floating property, and a superb photothermal conversion performance to the SSG. The temperature of the CCGA's upper surface can reach up to 42.6 °C under 1 sun irradiation, and for pure water, the evaporation rate of CCGA can be up to 1.486 kg m^-2 h^-1, corresponding to a good photothermal conversion efficiency of 86.96%. It also exhibits an excellent desalination capability; e.g., the photothermal conversion efficiency of CCGA in NaCl (20 wt %) brine is measured to be 75.77% under 1 sun irradiation, and the fresh water obtained from artificial seawater can achieve the WHO's standard for domestic water. With the advantages of low cost and a simple preparation process, such biomass-based CCGA materials may have great potential as an efficient SSG device for seawater desalination.

Scalable Fabrication of Conjugated Microporous Polymer Sponges for Efficient Solar Steam Generation

Seawater evaporation realized by solar-thermal conversion represents one of the most sustainable and effective strategies to obtain fresh water. Many approaches have been proposed to achieve high efficiencies of solar-thermal conversion, but their practical applications are limited by the low scalability. Herein, novel porphyrin/aniline-based conjugated microporous polymers (PACMPs) are synthesized via a Buchwald-Hartwig coupling reaction, which are then integrated with polyurethane sponges via a simple dip-coating technique. The PACMP-modified sponges (PACSs) retain the high porosity of the sponge substrate and excellent solar-thermal conversion properties of PACMPs. Under standard solar irradiation (1 kW m^-2), PACSs achieve a high seawater evaporation rate of 1.31 kg m^-2 h^-1 with a solar-thermal conversion efficiency of 86.3%. PACSs show no salt accumulation and high performance of desalination and dye decolorization, removing >99.9% salt and >99.2% dye, respectively. The self-floating characteristic, recyclability, and durable solar-thermal evaporation efficiencies enable PACSs to be promising candidate materials for seawater desalination and sewage purification.

Efficient Solar-Driven Water Purification Based on Biochar with Multi-Level Pore Bundle Structure for Preparation of Drinking Water

Water is an important source for humankind. However, the amount of available clean water has rapidly reduced worldwide. To combat this issue, the solar-energy-driven evaporation technique is newly proposed to produce clean water. Here, biochar derived from sorghum stalk with a multi-level pore bundle structure is utilized to fabricate a solar-driven evaporator for the first time. The biochar displays rapid water transfer and low thermal conductivity (ca. 0.0405 W m⁻¹ K⁻¹), which is vitally important for such an application purpose. The evaporation rate and energy conversion efficiency of the solar evaporator based on carbonized sorghum stalk can achieve up to 3.173 kg m⁻² h⁻¹ and 100%, respectively, which are better than most of the previously reported biomass materials. Furthermore, the carbonized sorghum stalk also displays good resistance to salt crystallization, anti-acidic/basic, and organic pollutants by producing drinking water using seawater, acidic/basic waste water, and organic polluted water, respectively. The direct application of processed water in food production was also investigated. The present solar steam evaporator based on the carbonized sorghum stalk has the potential to create practical drinking water production by using various water sources.

Fe3O4/PPy-Coated Superhydrophilic Polymer Porous Foam: A Double Layered Photothermal Material with a Synergistic Light-to-Thermal Conversion Effect toward Desalination

Solar steam generation has been considered as one of the most promising strategies for production of fresh water using renewable solar energy. Herein, we prepared a polymer porous foam (HPSS) by a facile hydrothermal method. The HPSS presents a superhydrophilic wettability, an interpenetrating macroporous structure, and low thermal conductivity, which can well satisfy the criteria as an ideal candidate for photothermal materials. The HPSS/Fe₃O₄/PPy (polypyrrole) evaporator, of which a Fe₃O₄/PPy binary optical system served as a light absorption layer and HPSS was used as a porous substrate, was constructed through in situ growth of Fe₃O₄ particles followed by interfacial polymerization of PPy on the surface of HPSS. HPSS/Fe₃O₄/PPy shows an excellent light absorption capacity (92%) and photothermal conversion performance, with the solar energy conversion efficiency reaching up to 94.7% under 1 sun irradiation, which is much higher than that of HPSS/PPy (84.8%) composed of a unitary PPy light absorption layer. Interestingly, the presence of Fe₃O₄ particles could make directional migration in a magnetic field possible, thus facilitating its recovery as a self-floating solar generator in an open water area. Moreover, the HPSS/Fe₃O₄/PPy evaporator displays outstanding salt resistance properties and stability in various saline solutions, thus having great potential in practical desalination.

Aligned Millineedle Arrays for Solar Power Seawater Desalination with Site-Specific Salt Formation

As a sustainable and clean water production technology, solar thermal water evaporation has been extensively studied in the past few years. One challenge is that upon operation, salt would form on surface of the solar absorbers leading to inefficient water supply and light absorption and thus much reduced water vaporization rate. To address this problem, a simple solar evaporator based on an array of aligned millineedles for efficient solar water evaporation and controlled site-specific salt formation is demonstrated. The maximum solar evaporation rate achieved is 2.94 kg m^-2 h^-1 under one Sun irradiation in brine of high salinity (25 wt% NaCl), achieving energy conversion efficiency of 94.5% simultaneously. More importantly, the spontaneously site-specific salt formation on the tips of millineedles endows this solar evaporator with salt harvesting capacity. Rationally separating the clean water and salt from brine by condensation and gravity assistance, this tip-preferential crystallization solar evaporator is not affected by the salt clogging compared with conventional 2D solar evaporators. This study provides new insights on the design of solar evaporators and advances their applications in sustainable seawater desalination and wastewater management.

Flexible, affordable and environmentally sustainable solar vapor generation based on ferric tannate/bacterial cellulose composite for efficient desalination solutions

Desalination by solar steam generation (SSG) system is a green technology to produce pure water, which can address the issue of water scarcity. A novel photothermal material for the SSG system was fabricated by immersing bacterial cellulose (BC) sequentially into tannic acid (TA) and iron(iii) (Fe³⁺) solutions. Surface analysis of the resulting BC–TA–Fe³⁺ (BTF) material showed that coordination nanocomplexes between Fe³⁺ and hydroxyl groups of TA were formed on the surface of cellulose nanofibers. BTF material exhibited high sunlight absorption (∼95%), hydrophilic, self-cleaning properties, and excellent structural stability. SSG systems based on BTF had an evaporation efficiency of 91% and an evaporation rate of 1.56 kg m⁻² h⁻¹ under 1 sun illumination. Then, an efficient desalination device based on the larger-scale BTF material was fabricated to produce freshwater, the amount of freshwater per day was 5.6 kg m⁻² on a sunny day. BTF material, thus, showed great potential in seawater desalination applications along with simple, versatile, scalable, and affordable fabrication methods.

The BTF material showed a great potential for seawater desalination applications along with a simple, versatile, scalable, and affordable fabrication method.

Modified Hollow Glass Microspheres/Reduced Graphene Oxide Composite Aerogels with Low Thermal Conductivity for Highly Efficient Solar Steam Generation

Solar steam generation (SSG) as a pollution-free and sustainable way for desalination or wastewater treatment has attracted great attention in recent years. Herein, we report the fabrication of novel aerogels GAHAS and GAHAF composed of 3-aminopropyltriethoxysilane (KH550)-modified hollow glass microspheres (HGM) and reduced graphene oxide (RGO) by a sol-gel method for highly efficient SSG. The RGO can well wrap on modified HGM and form an interpenetrated porous structure with an excellent mechanical property. In addition, benefiting from the hollow structure of HGM, GAHAS obtained by supercritical CO₂ drying well maintains the original structure of the hydrogel and shows low thermal conductivity (0.0823 W m^-1 K^-1) in the wet state and self-floating ability. Combined with its superhydrophilic wettability and high light absorption (ca. 93%), the as-prepared GAHAS shows an outstanding photothermal conversion efficiency of 89.13% under 1 sun (1 kW m^-2) illumination and excellent stability. Moreover, from the simulated seawater outdoor solar desalination experiment, it was found that the concentrations of the four primary ions K⁺, Ca²⁺, Na⁺, and Mg²⁺ in purified water are 1.65, 0.09, 1.42, and 0.32 mg L^-1, respectively, and fully meet drinking water standards. Thus, our GAHAS aerogel shows great potential for practical application in SSG. This work enriches the photothermal materials and may provide a new idea for design and creation of HGM-based photothermal materials with low thermal conductivity, tunable porosity, high mechanical strength, self-floating ability, and high solar energy conversion efficiency for SSG.

Dual-Functional Graphene Oxide-Based Photothermal Materials with Aligned Channels and Oleophobicity for Efficient Solar Steam Generation

Desalination by solar steam generation (SSG) has emerged as one of the most efficient approaches to address the issue of global water shortage. In this work, novel graphene oxide (GO)-based solar steam generators (GO-SSGs) with aligned channels were prepared by directional freezing and simple carbonization of a hydrogel composed of GO and poly(vinyl alcohol) (PVA). Benefitting from their excellent light absorption (light absorption efficiency exceeds 94%), better thermal insulation (thermal conductivity, 0.259 W/(m K)), and suitable porous structure, which facilitates rapid water transportation, the GO-SSGs show superior SSG performance with a high solar energy conversion efficiency of up to 92% achieved under an irradiation of 1.0 kW/m². Interestingly, uniquely aligned channels endow them with good salt-rejection performance; the solar energy conversion efficiency of GO-SSGs in 20 wt % NaCl, KCl, and MgCl₂ brine can reach more than 85%. To improve their antifouling performance, a chemically hydrophilic and oleophobic modification was conducted, making it possible to run SSG even in oily wastewater; for instance, a solar energy conversion efficiency of 84% was obtained in an aqueous solution containing 10 wt % n-hexadecane. Compared with the existing photothermal materials, these materials show advantages of simple manufacture, high SSG efficiency, superior salt tolerance, and antifouling performance, which make them promising candidates as a kind of new high-performance photothermal materials for desalination even in oily wastewater, thus further expanding the scope of their practical SSG application.

Cationic Photothermal Hydrogels with Bacteria-Inhibiting Capability for Freshwater Production via Solar-Driven Steam Generation

Solar-driven steam generation has been recognized as a sustainable and low-cost solution to freshwater scarcity using abundant solar energy. To harvest freshwater, various interfacial evaporators with rational designs of photothermal materials and structures have been developed concentrating on increasing the evaporation rate in the past few years. However, pathogenic microorganism accumulation on the evaporators by long-duration contact with natural water resources may lead to the deterioration of water transportation and the reduction of the evaporation rate. Here, we develop cationic photothermal hydrogels (CPHs) based on [2-(methacryloyloxy)ethyl]trimethylammonium chloride (METAC) and photothermal polypyrrole (PPy) with bacteria-inhibiting capability for freshwater production via solar-driven steam generation. A rapid water evaporation rate of 1.592 kg m^-2 h^-1 under simulated solar irradiation is achieved with CPHs floating on the water surface. Furthermore, we find that CPHs possess nearly 100% antibacterial performance against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). The significant bacteria-inhibiting capability is mainly attributed to the large number of ammonium groups on the CPH network. Moreover, we show that CPHs exhibit good applicability with stable evaporation in natural lake water over 2 weeks, and the number of bacteria in purified lake water is significantly reduced. The device based on CPHs can achieve ∼0.49 kg m^-2 h^-1 freshwater production from lake water under natural sunlight. This study provides an attractive strategy for the evaporator to inhibit biological contamination and a potential way for long-term stable freshwater production from natural water resources in practical application.

Facile Preparation of a Carbon-Based Hybrid Film for Efficient Solar-Driven Interfacial Water Evaporation

Solar-driven interfacial water evaporation is one promising technology for seawater desalination and sewage purification because it offers a feasible and sustainable strategy to relieve global water scarcity. Herein, a novel hybrid film composed of recycled carbon soot and poly(vinyl alcohol) is developed by a very simple, green, and highly scalable "salt-assisted" assembling method. The hybrid film possesses characteristics with a porous structure, superhydrophilicity, ∼100% light absorption, and low thermal conductivity, which can effectively convert light into heat under solar illumination. Consequently, the hybrid film can achieve a photothermal conversion efficiency of 91.5% under a stimulated solar irradiation of 1 kW m^-2. Furthermore, the hybrid film can be applied for seawater desalination and dye wastewater purification. The findings of our work not only provide a new photothermal platform with high light-to-thermal conversion ability and good reusability but also open a new avenue for the applications of carbon soot-based hybrid films in solar-assisted water evaporation and sewage purification.

Three-dimensional hierarchical oxygen vacancy-rich WO3-decorated Ni foam evaporator for high-efficiency solar-driven interfacial steam generation

Solar steam generation is considered to be an effective strategy to alleviate the global water shortage problem. Therefore, exploring highly efficient and thermal stability photothermal conversion materials is highly essential and urgent. In this work, we develop a three-dimensional (3D) oxygen vacancy-rich WO₃ with ''nanorod array grown on nanosheet array" unique architecture decorated on Ni foam (denoted as WO_3-x/NF) through a simple and effective hydrothermal method followed by an annealing route, which is applied as light-absorbing material. The 3D hierarchical porous unique structure of the WO_3-x/NF evaporator can supply a channel steam escaping and enhance the light trapping due to the multi-scattering effect, and the localized surface plasmon resonance (LSPR) effects of WO_3-x also contribute to increase the light absorption in the full solar spectrum. The as-prepared WO_3-x/NF evaporator reveals a high solar absorption (95%), an evaporation rate of 1.50 kg m^-2 h^-1 under one sun illumination, and a light-to-heat conversion efficiency of about 88%, as well as stable salt-resistance performance. The water purification results show that WO_3-x/NF evaporator has a significant effect on seawater desalination without significant salt accumulation and purification of heavy metal wastewater. Furthermore, the first-principles calculations reveal that WO₃ with oxygen vacancies has a narrower bandgap, which is more conducive to absorb solar energy from the whole spectrum. This work can provide a new avenue toward the design of other high photothermal conversion system.

Self-cleaning and flexible filters based on aminopyridine conjugated microporous polymers nanotubes for bacteria sterilization and efficient PM2.5 capture

The capture and elimination of harmful particulate matter (PM) both in air and water is of great importance for human health and environmental sustainability. Here, we demonstrate a novel strategy for the exploitation of conjugated microporous polymer bearing aminopyridine moiety (A-CMPs) as an advanced filter for bacteria sterilization and efficient PM capture. The A-CMPs network shows a hierarchically porous structure with mechanical robustness and flexibility, which facilitates to filtration especially for PM with different particle sizes. The capture efficiency of A-CMPs aerogels for PM_2.5 and PM₁₀ were respectively up to PM_2.5 ≥ 99.57 ± 0.19% and PM₁₀ ≥ 99.98 ± 0.01% in a long-term durability test and easy to be regenerated. Moreover, the A-CMPAs features excellent superhydrophobicity, which is difficult to saturate with water aerosols in humid air (RH: 89 ± 3%) and in turn shows superior stability and high-performance in terms to capture efficiency. More importantly, the A-CMP monolith exhibits excellent antimicrobial activity and high concentrations of bacterial suspension (e.g., using E. coli as probe bacterial) could be effectively captured and quickly killed during filtration, which endows the A-CMPs additional sterilization performance and thus is of great technological significance with remarkable potentials as a new kind of advanced filter for multifunctional filtration in both air and water.

Ionic Liquid-Assisted Alignment of Corn Straw Microcrystalline Cellulose Aerogels with Low Tortuosity Channels for Salt-Assistance Solar Steam Evaporators

The development of a highly salt-resistant solar evaporator with long-term energy conversion is essential for practical solar desalination. Herein, we first report the ionic liquid-assisted alignment of corn straw-based microcrystalline and oxidized microcrystalline cellulose for preparation of biomass aerogel (abbreviated as CSMCA and CSOMCA) evaporators with low tortuosity channels for salt-assistance solar steam generation. By coating of carbonized cornstalk nanoparticles onto CSMCA and CSOMCA as light-absorbing layers (named C-CSMCA and C-CSOMCA), the light absorption of C-CSMCA and C-CSOMCA reaches 92 and 95%, respectively. The formation of strong H-bonding between pyranoid rings of cellulose in the presence of the ionic liquid would result in a reorientation of microcrystalline cellulose, which makes it possible to create vertically aligned channels of CSMCA and CSOMCA after replacement of solvents, followed by freeze drying. Combined with their low thermal conductivity (0.037 and 0.043 W m^-1 K^-1), high porosity, and intrinsic superhydrophilicity, C-CSMCA and C-CSOMCA exhibit high evaporation rates (1.44 and 1.36 kg m^-2 h^-1) and excellent energy conversion efficiencies (88 and 84%). In particular, bearing with vertically aligned channels, C-CSMCA and C-CSOMCA possess excellent salt tolerance for solar desalination due to a rapid resolving and return of the crystalline salt into water, for example, no surface salt crystallization for C-CSMCA after 20 days of continuous evaporation. Moreover, both C-CSMCA and C-CSOMCA have excellent sewage treatment capacity and can efficiently absorb dyes and heavy-metal ions in water bodies, showing great potential in actual desalination and sewage treatment based on their cost-effective, simple, scalable, and green manufacture.