Identification of Catalytic Active Sites in Nitrogen-Doped Carbon for Electrocatalytic Dechlorination of 1,2-Dichloroethane

Dopamine-modified cobalt spinel nanoparticles as an active catalyst for the acidic oxygen evolution reaction

The development of efficient non-noble metal electrocatalysts for the oxygen evolution reaction (OER) under acidic conditions remains a critical challenge. Herein, we report a N-doped carbonaceous component-engineered Co3O4 (NCEC) catalyst synthesized via the sol-gel method. Dopamine hydrochloride (DA)-derived nitrogen-doped carbonaceous components were found to boost the OER performance of Co3O4. The optimized catalyst can reach an overpotential as low as 330 mV in 1 M H2SO4 at a current density of 10 mA cm-2 and maintains a good long-term stability of 60 hours. In particular, we found that the thermodynamic overpotential was inversely proportional to the content of oxidized N and pyridinic N, whereas it was directly proportional to the pyrrolic-N content. Our experiments and density functional theory (DFT) calculations confirm that the optimized catalyst exhibits enhanced charge transfer and the oxidized N species on Co3O4 is responsible for the high catalytic activity. Our study suggests that the performance of NCEC in acidic media can be further optimized by enhancing the content of oxidized N species.

P-doped Co3S4/NiS2 heterostructures embedded in N-doped carbon nanoboxes: Synergistical electronic structure regulation for overall water splitting

Water splitting using transition metal sulfides as electrocatalysts has gained considerable attention in the field of renewable energy. However, their electrocatalytic activity is often hindered by unfavorable free energies of adsorbed hydrogen and oxygen-containing intermediates. Herein, phosphorus (P)-doped Co3S4/NiS2 heterostructures embedded in N-doped carbon nanoboxes were rationally synthesized via a pyrolysis-sulfidation-phosphorization strategy. The hollow structure of the carbon matrix and the nanoparticles contained within it not only result in a high specific surface area, but also protects them from corrosion and acts as a conductive pathway for efficient electron transfer. Density functional theory (DFT) calculations indicate that the introduction of P dopants improves the conductivity of NiS2 and Co3S4, promotes the charge transfer process, and creates new electrocatalytic sites. Additionally, the NiS2-Co3S4 heterojunctions can enhance the adsorption efficiency of hydrogen intermediates (H*) and lower the energy barrier of water splitting via a synergistic effect with P-doping. These characteristics collectively enable the titled catalyst to exhibit excellent electrocatalytic activity for water splitting in alkaline medium, requiring only small overpotentials of 150 and 257 mV to achieve a current density of 10 mA cm-2 for hydrogen and oxygen evolution reactions, respectively. This work sheds light on the design and optimization of efficient electrocatalysts for water splitting, with potential implications for renewable energy production.

Electrochemical reduction of wastewater by non-noble metal cathodes: From terminal purification to upcycling recovery

A shift beyond conventional environmental remediation to a sustainable pollutant upgrading conversion is extremely desirable due to the rising demand for resources and widespread chemical contamination. Electrochemical reduction processes (ERPs) have drawn considerable attention in recent years in the fields of oxyanion reduction, metal recovery, detoxification and high-value conversion of halogenated organics and benzenes. ERPs also have the potential to address the inherent limitations of conventional chemical reduction technologies in terms of hydrogen and noble metal requirements. Fundamentally, mechanisms of ERPs can be categorized into three main pathways: direct electron transfer, atomic hydrogen mediation, and electrode redox pairs. Furthermore, this review consolidates state-of-the-art non-noble metal cathodes and their performance comparable to noble metals (e.g., Pd, Pt) in electrochemical reduction of inorganic/organic pollutants. To overview the research trends of ERPs, we innovatively sort out the relationship between the electrochemical reduction rate, the charge of the pollutant, and the number of electron transfers based on the statistical analysis. And we propose potential countermeasures of pulsed electrocatalysis and flow mode enhancement for the bottlenecks in electron injection and mass transfer for electronegative pollutant reduction. We conclude by discussing the gaps in the scientific and engineering level of ERPs, and envisage that ERPs can be a low-carbon pathway for industrial wastewater detoxification and valorization.

Electrocatalytic hydro-dehalogenation of halogenated organic pollutants from wastewater: A critical review

Halogenated organic pollutants are often found in wastewater effluent although it has been usually treated by advanced oxidation processes. Atomic hydrogen (H*)-mediated electrocatalytic dehalogenation, with an outperformed performance for breaking the strong carbon-halogen bonds, is of increasing significance for the efficient removal of halogenated organic compounds from water and wastewater. This review consolidates the recent advances in the electrocatalytic hydro-dehalogenation of toxic halogenated organic pollutants from contaminated water. The effect of the molecular structure (e.g., the number and type of halogens, electron-donating or electron-withdrawing groups) on dehalogenation reactivity is firstly predicted, revealing the nucleophilic properties of the existing halogenated organic pollutants. The specific contribution of the direct electron transfer and atomic hydrogen (H*)-mediated indirect electron transfer to dehalogenation efficiency has been established, aiming to better understand the dehalogenation mechanisms. The analyses of entropy and enthalpy illustrate that low pH has a lower energy barrier than that of high pH, facilitating the transformation from proton to H*. Furthermore, the quantitative relationship between dehalogenation efficiency and energy consumption shows an exponential increase of energy consumption for dehalogenation efficiency increasing from 90% to 100%. Lastly, challenges and perspectives are discussed for efficient dehalogenation and practical applications.

Cubic CuFe2O4 Spinel with Octahedral Fe Active Sites for Electrochemical Dechlorination of 1,2-Dichloroethane

CuFe₂O₄ spinel has been considered as a promising catalyst for the electrochemical reaction, while the nature of the crystal phase on its intrinsic activity and the kind of active site need to be further explored. Herein, the crystal phase-dependent catalytic behavior and the main active sites of CuFe₂O₄ spinel for electrochemical dechlorination of 1,2-dichloroethane are carefully studied based on the combination of experiments and theoretical calculations. Cubic and tetragonal CuFe₂O₄ are successfully prepared by a facile sol-gel method combined with high temperature calcination. Impressively, CuFe₂O₄ with the cubic phase shows a higher activity and ethylene selectivity compared to CuFe₂O₄ with the tetragonal phase, suggesting a significant facilitation of electrocatalytic performance by the cubic crystal structure. Moreover, the octahedral Fe atom on the surface of cubic CuFe₂O₄(311) is the active site responsible to produce ethylene with the energy barrier of 0.40 eV. This work demonstrates the significance of crystal phase engineering for the optimization of electrocatalytic performance and offers an efficient strategy for the development of advanced electrocatalysts.

Selective dechlorination degradation of chlorobenzenes by dual single-atomic Fe/Ni catalyst with M-N/M-O active sites synergistic

Removal and detoxification of chlorobenzenes have attracted public concern, multiple active sites single-atom Fe and single-atom Ni composite nitrogen-doped graphene (Fe_SA/CN/Ni_SA) cathode catalyst supplied generation and adsorption capacity of hydrogen and hydroxyl active species. M-O active sites coupled with M-N improved activity and stability of the catalyst, and decreased bond breaking energy barrier of C-Cl, Fe_SA/CN/Ni_SA-NiF cathode showed superior removal performance of chlorinated aromatic hydrocarbons (monochlorobenzene: 98.9%, dichlorobenzene: over 90.4%, trichlorobenzene: over 85.7%) and selectivity. Chlorobenzenes were dechlorinated under low stepwise voltage on the Fe_SA/CN/Ni_SA-NiF cathode. The efficiencies of stepwise dechlorination reactions of chlorobenzenes were all above 76%, Faradaic efficiencies were above 71.8%. The Fe_SA/CN/Ni_SA-NiF cathode was not sensitive to the molecular structure and has overcome the high energy barrier of chlorobenzenes molecular structure. The electrophilic attack of H*_ads formed hyperconjugation bond weakened the possibility of the Cl atom forming a bond with the benzene ring, and was favorable for the Cl position to achieve single-electron transfer dechlorination. The selective stepwise dechlorination degradation of chlorobenzenes by Fe_SA/CN/Ni_SA-NiF cathode with multiple active sites demonstrated the advantaged performance of M-O and M-N active sites coupled synergistic in electrochemical reduction and degradation, providing a strategy for product-selective degradation of chlorinated aromatic hydrocarbons.

Efficient electrocatalytic valorization of chlorinated organic water pollutant to ethylene

Electrochemistry can provide an efficient and sustainable way to treat environmental waters polluted by chlorinated organic compounds. However, the electrochemical valorization of 1,2-dichloroethane (DCA) is currently challenged by the lack of a catalyst that can selectively convert DCA in aqueous solutions into ethylene. Here we report a catalyst comprising cobalt phthalocyanine molecules assembled on multiwalled carbon nanotubes that can electrochemically decompose aqueous DCA with high current and energy efficiencies. Ethylene is produced at high rates with unprecedented ~100% Faradaic efficiency across wide electrode potential and reactant concentration ranges. Kinetic studies and density functional theory calculations reveal that the rate-determining step is the first C-Cl bond breaking, which does not involve protons-a key mechanistic feature that enables cobalt phthalocyanine/carbon nanotube to efficiently catalyse DCA dechlorination and suppress the hydrogen evolution reaction. The nanotubular structure of the catalyst enables us to shape it into a flow-through electrified membrane, which we have used to demonstrate >95% DCA removal from simulated water samples with environmentally relevant DCA and electrolyte concentrations.

Adsorption and membrane separation for removal and recovery of volatile organic compounds

Volatile organic compounds (VOCs) are a crucial kind of pollutants in the environment due to their obvious features of severe toxicity, high volatility, and poor degradability. It is particularly urgent to control the emission of VOCs due to the persistent increase of concentration and the stringent regulations. In China, clear directions and requirements for reduction of VOCs have been given in the "national plan on environmental improvement for the 13th Five-Year Plan period". Therefore, the development of efficient technologies for removal and recovery of VOCs is of great significance. Recovery technologies are favored by researchers due to their advantages in both recycling VOCs and reducing carbon emissions. Among them, adsorption and membrane separation processes have been extensively studied due to their remarkable industrial prospects. This overview was to provide an up-to-date progress of adsorption and membrane separation for removal and recovery of VOCs. Firstly, adsorption and membrane separation were found to be the research hotspots through bibliometric analysis. Then, a comprehensive understanding of their mechanisms, factors, and current application statuses was discussed. Finally, the challenges and perspectives in this emerging field were briefly highlighted.

Catalytic Oxygen Activation over the Defective CuO Nanoparticles for Ultrafast Dehalogenation

The nucleophilic superoxide radical (O₂^•-)-based dehalogenation reaction shows great potential to degrade the toxic halogenated organic compounds (HOCs). But such an O₂^•--mediated reductive reaction often suffers from the competition of the secondary oxidative species (e.g., •OH), leading to inferior electron efficiency and possible disinfection byproduct formation. Here, an O₂^•--dominant ultrafast dehalogenation system is developed via molecular O₂ activation by the oxygen vacancy (OV)-rich CuO nanoparticles (nCuO). The nCuO delivers a remarkable dechlorination rate constant of 3.92 × 10^-2 L min^-1 m^-2 for 2,4-dichlorophenol, much higher than that of the conventional zerovalent (bi)metals. The absorbed O₂ on the nCuO surface is exclusively responsible for O₂^•- generation, and its reactivity increases with the elevated OV content because of the enhanced orbital hybridization between the O p- and Cu d-orbitals. More importantly, the ubiquitous carbonate species firmly bound to the surface OVs block the formation of the secondary oxidative species via H₂O₂ activation, assuring the dominant role of the in situ generated O₂^•- for the selective HOC dehalogenation. The carbonate-deactivated OVs of the nCuO can be feasibly recovered via air annealing for sustainable dehalogenation. This work provides a new opportunity for selective O₂^•- generation via interfacial defect engineering for dehalogenation and other environmental applications.

Highly Efficient Electrocatalytic Upgrade of n-Valeraldehyde to Octane over Au SACs-NiMn2 O4 Spinel Synergetic Composites

In this work, electrocatalytic upgrade of n-valeraldehyde to octane with higher activity and selectivity is achieved over Au single-atom catalysts (SACs)-NiMn₂ O₄ spinel synergetic composites. Experiments combined with density functional theory calculation collaboratively demonstrate that Au single-atoms occupy surface Ni²⁺ vacancies of NiMn₂ O₄ , which play a dominant role in n-valeraldehyde selective oxidation. A detailed investigation reveals that the initial n-valeraldehyde molecule preferentially adsorbs on the Mn tetrahedral site of NiMn₂ O₄ spinel synergetic structures, and the subsequent n-valeraldehyde molecule easily adsorbs on the Ni site. Specifically, Au single-atom surficial derivation over spinel lowers the adsorption energy (E_ads ) of the initial n-valeraldehyde molecule, which will facilitate its adsorption on the Mn site of Au SACs-NiMn₂ O₄ . Furthermore, the single-atom Au surficial derivation not only alters the electronic structure of Au SACs-NiMn₂ O₄ but also lower the E_ads of subsequent n-valeraldehyde molecule. Hence, the subsequent n-valeraldehyde molecules prefer adsorption on Au sites rather than Ni sites, and the process of two alkyl radicals originating from Mn-C₄ H₉ and Au-C₄ H₉ dimerization into an octane is accordingly accelerated. This work will provide an avenue for the rational design of SACs and supply a vital mechanism for understanding the electrocatalytic upgrade of n-valeraldehyde to octane.

Functionalized Activated Carbon for Competing Adsorption of Volatile Organic Compounds and Water

The interfacial interaction of activated carbon with volatile organic compounds (VOCs) is seriously affected by water vapor. Therefore, it is vital to enhance the hydrophobic performance of activated carbon for expanding its application in industrial and environmental fields. Herein, a series of hydrophobic activated carbon was fabricated by tailored mixed siloxane and applied in dynamic competitive adsorption at 0, 50, and 90% humidity. Simultaneously, the diffusion molecular models and multicomponent adsorption experiments were used to study the adsorption and diffusion mechanisms. The hydrophobicity of activated carbon was significantly improved by loading of mixed siloxane, in which the equilibrium water absorption decreased from 21.9 to 7.2% and the contact angles increased by 70.10°. Meanwhile, dynamic competitive adsorption at different humidities indicated that the siloxane-functionalized activated carbons (SACs) showed much better competitive adsorption performances for VOCs than original activated carbon, which was further confirmed by the theoretical calculations of adsorption energy. In addition, a remarkable adsorption selectivity and reusability could be demonstrated to VOCs with different polarities on SACs. This study not only provides a new strategy for the hydrophobic modification of activated carbon materials but also offers theoretical guidance for the treatment of gas streams with significant water contents.

Ozone-Activated Cataluminescence Sensor System for Dichloroalkanes Based on Silica Nanospheres

The detection and monitoring of dichloroalkanes, which are typical chlorinated volatile organic compounds (CVOCs) with obvious biological toxicity, is of significance for environmental pollution and public health. Herein, a novel ozone-activated cataluminescence (CTL) sensor system based on silica nanospheres was developed for highly sensitive and fast quantification of dichloroalkanes. A typical CTL system coupled with a plasma-ozone-assist unit was designed for promoting the CTL response of dichloroalkanes. The ozone generated by plasma provides a new pathway of catalytic oxidation process, which accompanied by the CTL signal amplification of dichloroalkanes results in an enhanced CTL sensor system with improved limit of detection (1,2-dichloroethane: 0.04 μg mL^-1, 1,2-dichloropropane: 0.03 μg mL^-1) and benign selective performance under the interference of CO₂, H₂O, NO, NO₂, SO₂, CS₂, and other common CVOCs. Moreover, a segmented CTL mechanism including co-adsorption of ozone and dichloroalkanes, thermal elimination, the ozonation route, and a luminous step was ratiocinated based on multiple characterizations and discussion. The proposed methodology and theory open up an attractive perspective for the analysis of less active volatile organic compounds.

Hexachloroethane dechlorination in sulfide-containing aqueous solutions catalyzed by nitrogen-doped carbon materials

This study demonstrated that nitrogen-doped carbon materials (NCMs) could effectively catalyze the chlorine elimination process in hexachloroethane (HCA) declorination in sulfide-containing environments for the first time. The k_obs values of HCA dechlorination by sulfide in the presence of 10 mg/L NCMs were higher than that of no mediator at pH 7.3 by one or two orders of magnitude. The catalytic capabilities of NCMs on HCA dechlorination were evident in common ranges of natural pH (5.3-8.9) and it could be accelerated by the increase of pH but be suppressed by the presence of dissolved humic acid. Moreover, NCMs exhibited much better catalytic capability on HCA dechlorination compared to the carbon materials, mainly owing to the combined contributions of pyridine N, including enhanced nucleophilic attack to HCA molecule by generating newborn C-S-S and activation of HCA molecule by elongating C-Cl bonds. The functions of pyridine N in micron-sized NCMs with mesopores were better than in nano-sized NCMs on HCA dechlorination. These findings displayed the potential of NCMs, when released into sulfide-containing environments, may significantly increase the dechlorination of chlorinated aliphatic hydrocarbons.

Electrocatalytic Dechlorination of Dichloromethane in Water Using a Heterogenized Molecular Copper Complex

The remediation of organohalides from water is a challenging process in environment protection and water treatment. Herein, we report a molecular copper(I) complex with two triazole units, CuT2, in a heterogeneous aqueous system that is capable of dechlorinating dichloromethane (CH₂Cl₂) to afford hydrocarbons (methane, ethane, and ethylene). The catalytic performance is evaluated in water and presented high Faradaic efficiency (average 70% CH₄) across a range of potentials (-1.1 to -1.6 V vs Ag/AgCl) and high activity (maximum -25.1 mA/cm² at -1.6 V vs Ag/AgCl) with a turnover number of 2.0 × 10⁷. The CuT2 catalyst also showed excellent stability for 14 h of constant exposure to CH₂Cl₂ and 10 h of CH₂Cl₂ exposure cycling. The control compound, a copper-free triazole unit (T1), was also investigated under the same condition and showed inferior catalytic activity, indicating the importance of the copper center. Plausible catalytic mechanisms are proposed for the formation of C₁ and C₂ products via radical intermediates. Computational studies provided additional insight into the reaction mechanism and the selectivity toward the CH₄ formation. The findings in this study demonstrate that complex CuT2 is an efficient and stable catalyst for the dehalogenation of CH₂Cl₂ and could potentially be used for the exploration of the removal of halogenated species from aqueous systems.

Surface Ligand Environment Boosts the Electrocatalytic Hydrodechlorination Reaction on Palladium Nanoparticles

We present an enhanced catalytic efficiency of palladium (Pd) nanoparticles (NPs) for the electrocatalytic hydrodechlorination (EHDC) reaction by incorporating the tetraethylammonium chloride (TEAC) ligand into the surface of NPs. Both experimental and theoretical analyses reveal that the surface-adsorbed TEAC is converted to molecular amine (primarily triethylamine) under reductive potentials, forming a strong ligand-Pd interaction that is beneficial to the EHDC kinetics. Using the EHDC of 2,4-dichlorophenol (2,4-DCP), a dominant persistent pollutant identified by the U.S. Environmental Protection Agency, as an example, the Pd/amine composite delivers a mass activity of 2.32 min^-1 g_Pd^-1 and a specific activity of 0.16 min^-1 cm^-2 at -0.75 V versus Ag/AgCl, outperforming Pd and most of the previously reported catalysts. The mechanistic study reveals that the amine ligand offers three functions: the H⁺-pumping effect, the electronic effect, and the steric effect, providing a favorable environment for the generation of reactive hydrogen radicals (H*) for hydrogenolysis of the C-Cl bond. It also weakens the adsorption strength of EHDC products, alleviating their poisoning on Pd. Investigation into the intermediate products of EHDC on Pd/amine and the biological safety of the 2,4-DCP-contaminated water after EHDC treatment demonstrates that EHDC on Pd/amine is environmentally benign for halogenated organic pollutant abatement. This work suggests that the tuning of NP catalysis using facile ligand post-treatment may lead to new strategies to improve EHDC for environmental remediation applications.

Active Sites in Single-Atom Fe-Nx-C Nanosheets for Selective Electrochemical Dechlorination of 1,2-Dichloroethane to Ethylene

Electrochemical dechlorination of 1,2-dichloroethane (DCE) is one of the prospective and economic strategies for the preparation of high-value ethylene. However, the exploration of advanced electrocatalysts with high reactivity and selectivity and the identification of their active sites are still a challenge. Herein, a single-atom (SA) Fe-N_x-C nanosheet with the presence of a highly efficient Fe-N₄ coordination pattern is reported. The as-prepared single-atom electrocatalyst exhibits a higher reactivity and ethylene selectivity for DCE dechlorination reaction than those of the commercially adopted 20% Pt-C catalyst. By a combination of experiments and theoretical calculations, the atomically dispersed Fe center in the Fe-N₄ structure was unveiled to be the dominating active site for electrochemical production of ethylene. Our work would offer an approach for the rational development of SA materials and supply crucial insight into the mechanism of ethylene production through the DCE dechlorination reaction.