Spatially Resolved Dissolution and Speciation Changes of ZnO Nanorods during Short-Term in Situ Incubation in a Simulated Wastewater Environment

Toward Understanding the Environmental Risks of Combined Microplastics/Nanomaterials Exposures: Unveiling ZnO Transformations after Adsorption onto Polystyrene Microplastics in Environmental Solutions

Over recent decades, there has been a dramatic increase in the manufacture of engineered nanomaterials, which has inevitably led to their environmental release. Zinc oxide (ZnO) is among the more abundant nanomaterial manufactured due to its advantageous properties, used for piezoelectric, semiconducting, and antibacterial purposes. Plastic waste is ubiquitous and may break down or delaminate into smaller microplastics, leaving open the question of whether these small polymers may alter the fate of ZnO through adsorption within aquatic media (tap-water and seawater). Here, scanning electron microscopy analysis confirms the effective Zn nano/microstructures adsorption onto polystyrene surfaces after only 24-h incubation in the aquatic media. After pre-aging the nanomaterials for 7-days in different environmental media, nanoprobe X-ray absorption near-edge spectroscopy analysis reveals significant ZnO transformation toward Zn-sulfide and Zn-phosphate. The interaction between a commercial ZnO-based sunscreen with polystyrene and a cleanser consumer containing microbeads with ZnO nanomaterials is also studied, revealing the adsorption of transformed Zn-species in the microplastics surfaces, highlighting the environmental relevancy of this work. Understanding the structural and functional impacts of the microplastics/ZnO complexes, and how they evolve, will provide insights into their chemical nature, stability, transformations, and fate, which is key to predicting their bioreactivity in the environment.

In Situ Tracking of Crystal-Surface-Dependent Cu2O Nanoparticle Dissolution in an Aqueous Environment

Metal-oxide-based nanoparticles (MONPs) such as Cu₂O NPs have attracted growing attention, but the potential discharges of MONPs have raised considerable concern of their environmental fate including their dissolution behavior. The impacts of morphology on MONP dissolution are largely uncertain due to the lack of in situ tracking techniques. In this study, we combined a series of in situ technologies including liquid-cell transmission electron microscopy and fluorescence probes to reveal the in situ dissolution process of Cu₂O NPs in freshwater. Our results suggest that cubic Cu₂O NPs exhibit a higher dissolution quantity compared with spherical NPs of the same surface area. The difference was mainly related to the crystal surface, while other factors such as particle size or aggregation status showed minor effects. Importantly, we demonstrated the simultaneous growth of new small NPs and the dissolution of pristine Cu₂O NPs during the dissolution of Cu₂O NPs. Cubic Cu₂O NPs became much less soluble under O₂-limited conditions, suggesting that O₂ concentration largely affected the dependence of dissolution on the NP morphology. Our findings highlight the potential application of in situ techniques to track the environmental fates of MONPs, which would provide important information for assessing the ecological risks of engineered NPs.

Current Methods and Prospects for Analysis and Characterization of Nanomaterials in the Environment

Analysis and characterization of naturally occurring and engineered nanomaterials in the environment are critical for understanding their environmental behaviors and defining real exposure scenarios for environmental risk assessment. However, this is challenging primarily due to the low concentration, structural heterogeneity, and dynamic transformation of nanomaterials in complex environmental matrices. In this critical review, we first summarize sample pretreatment methods developed for separation and preconcentration of nanomaterials from environmental samples, including natural waters, wastewater, soils, sediments, and biological media. Then, we review the state-of-the-art microscopic, spectroscopic, mass spectrometric, electrochemical, and size-fractionation methods for determination of mass and number abundance, as well as the morphological, compositional, and structural properties of nanomaterials, with discussion on their advantages and limitations. Despite recent advances in detecting and characterizing nanomaterials in the environment, challenges remain to improve the analytical sensitivity and resolution and to expand the method applications. It is important to develop methods for simultaneous determination of multifaceted nanomaterial properties for in situ analysis and characterization of nanomaterials under dynamic environmental conditions and for detection of nanoscale contaminants of emerging concern (e.g., nanoplastics and biological nanoparticles), which will greatly facilitate the standardization of nanomaterial analysis and characterization methods for environmental samples.

ZnO Nanomaterials and Ionic Zn Partition within Wastewater Sludge Investigated by Isotopic Labeling

The increasing commercial use of engineered zinc oxide nanomaterials necessitates a thorough understanding of their behavior following their release into wastewater. Herein, the fates of zinc oxide nanoparticles (ZnO NPs) and ionic Zn in a real primary sludge collected from a municipal wastewater system are studied via stable isotope tracing at an environmentally relevant spiking concentration of 15.2 µg g-1. Due to rapid dissolution, nanoparticulate ZnO does not impart particle-specific effects, and the Zn ions from NP dissolution and ionic Zn display indistinguishable behavior as they partition equally between the solid, liquid, and ultrafiltrate phases of the sludge over a 4-h incubation period. This work provides important constraints on the behavior of engineered ZnO nanomaterials in primary sludge-the first barrier in a wastewater treatment plant-at low, realistic concentrations. As the calculated solid-liquid partition coefficients are significantly lower than those reported in prior studies that employ unreasonably high spiking concentrations, this work highlights the importance of using low, environmentally relevant doses of engineered nanomaterials in experiments to obtain accurate risk assessments.

Combination of biodegradation and fenton process for efficient removal of PDM/ZnO

In the present study, an investigation was conducted on the removal of polydiallyldimethylammonium chloride-acrylic-acrylamide-hydroxyethyl acrylate/ZnO nanocomposites (PDM/ZnO) through biodegradation and Fenton process coupled treatments. As revealed from the results of the chemical oxygen demand, the total organic carbon, the biochemical oxygen demand and the CO₂ production analysis, PDM/ZnO could be partially biodegraded. The optimal initial pH, the mixed liquid suspended solids concentration and additional carbon source (glucose) dosage in the biodegradation were 7.0, 4.0 g/L and 1.0 g/L, respectively. On the whole, NaCl, the coexisted metal cations (Cu²⁺, Zn²⁺ and Cr³⁺) and additional NH₄Cl inhibited the biodegradation of PDM/ZnO. PDM/ZnO was suggested to adversely affect on microbial community structure and activity. Optimum conditions for Fenton treatment were 50 mg/L Fe²⁺, 20 mL/L H₂O₂ and pH 2.0. Biodegradation showed that 64% of PDM/ZnO was removed. Besides, the combination of Fenton post-treatment could achieve an over 97% removal of PDM/ZnO. Thus, Fenton process combined biodegradation pre-treatment can act as an effective method to remove PDM/ZnO.

The Hard X-ray Nanoprobe beamline at Diamond Light Source

The Hard X-ray Nanoprobe beamline, I14, at Diamond Light Source is a new facility for nanoscale microscopy. The beamline was designed with an emphasis on multi-modal analysis, providing elemental mapping, speciation mapping by XANES, structural phase mapping using nano-XRD and imaging through differential phase contrast and ptychography. The 185 m-long beamline operates over a 5 keV to 23 keV energy range providing a ≤50 nm beam size for routine user experiments and a flexible scanning system allowing fast acquisition. The beamline achieves robust and stable operation by imaging the source in the vertical direction and implementing horizontally deflecting primary optics and an overfilled secondary source in the horizontal direction. This paper describes the design considerations, optical layout, aspects of the hardware engineering and scanning system in operation as well as some examples illustrating the beamline performance.

Lanthanum ions decorated 2-dimensional g-C3N4 for ciprofloxacin photodegradation

The low band gap energy and high surface area two-dimensional materials allow it to tune its basic properties using surface decoration. Here, La³⁺ are decorated on two-dimensional graphitic carbon nitride using a simple and easily scalable chemisorption process with an adsorption capacity of 657.32 mg g^-1. In the X-ray diffraction (XRD) study, the positive slope of the W-H plot elucidates the tensile strain generation (0.103) in La³⁺ ions decorated 2D-g-C₃N₄ (La³⁺-2D-g-C₃N₄). The high-resolution transmission electron microscope (HR-TEM) study and the higher I_D/I_G ratio (0.82) in the Raman spectroscopy study confirm the more defects intensification in La³⁺-2D-g-C₃N₄. The reduction in band gap energy for La³⁺-2D-g-C₃N₄ (from 2.83 eV to 2.21 eV) has shown a good correspondence with the band structures study as obtained from the DFT study. In the DFT study, the significant contributions of N atoms in charge transfer validate the N 1s findings from the X-ray photoelectron spectroscopy (XPS) study for La³⁺-2D-g-C₃N₄. La³⁺-2D-g-C₃N₄ shows the photodegradation efficiency (93%) of ciprofloxacin under UV irradiation, which is superior to pristine 2D-g-C₃N₄ (82%) as well as other g-C₃N₄ based nanocatalysts. Also, La³⁺ decoration results in enhancement (32.3%) in photodegradation kinetics rate. The degradation and kinetics studies in the presence of different scavengers ensure that the O₂- and OH^- radicals are mostly responsible for the ciprofloxacin photodegradation. The Liquid chromatographic-mass spectroscopy and the high-performance liquid chromatography studies confirm the photodegradation. The reusability of La³⁺-2D-g-C₃N₄ is tested up to the fifth cycle. FTIR and UV-visible absorption spectroscopy confirm the stability of the used photocatalyst.