Individual and Simultaneous Voltammetric Determination of Ultra-Trace Environmental Contaminant Dihydroxybenzene Isomers Based on a Composite Electrode Sandwich-like Structure

Voltammetric determination of hydrogen peroxide at decorated palladium nanoparticles/poly 1,5-diaminonaphthalene modified carbon-paste electrode

In this work, palladium nanoparticles (PdNPs)/p1,5-DAN/ carbon paste electrode (CPE) and p1,5-DAN/CPE sensors have been developed for determination of hydrogen peroxide. Both sensors showed a highly sensitive and selective electrochemical behaviour, which were derived from a large specific area of poly 1,5 DAN and super excellent electroconductibility of PdNPs. PdNPs/p1,5-DAN/CPE exhibited excellent performance over p1,5-DAN/CPE. Thus, it was used for detecting hydrogen peroxide (H2O2) with linear ranges of 0.1 to 250 µM and 0.2 to 300 µM as well as detection limits (S/N = 3) of 1.0 and 5.0 nM for square wave voltammetry (SWV) and cyclic voltammetry (C.V) techniques, respectively. The modified CPE has good reproducibility, adequate catalytic activity, simple synthesis and stability of peak response during H2O2 oxidation on long run that exceeds many probes. Both reproducibility and stability for H2O2 detection are attributable to the PdNPs immobilized on the surface of p1,5-DAN/CPE. The modified CPE was used for determining H2O2 in real specimens with good stability, sensitivity, and reproducibility.

Synthesis of morphology-controlled N-doped porous carbon for simultaneous electrochemical sensing of dihydroxybenzene isomers

Different morphology of N-doped carbon materials, including three-dimensional interconnected N-doped hierarchically porous carbon networks (3D-NC), two-dimensional ultrathin porous carbon nanosheets (2D-NC), and bulk N-doped carbon with micron size (bulk-NC), was easily prepared by using NaCl crystal templates-assisted strategy. Compared with bare glassy carbon, bulk-NC, and 2D-NC, the as-synthesized 3D-NC exhibits excellent electrochemical activity toward the oxidation and sensing of three kinds of common environmental pollutants dihydroxybenzene isomers (hydroquinone (HQ), catechol (CC), and resorcinol (RS)). The impressive electrochemical activity of 3D-NC can be interpreted by its large specific surface area, continuous network-like morphology, superior electro-catalytic ability, and strong accumulation efficiency. Differential pulse voltammetry (DPV) test showed the 3D-NC-modified electrode exhibited three well-separated oxidation peaks at 0.05 V, 0.14 V, and 0.45 V vs. saturated calomel electrode (SCE) for HQ, CC, and RS, and their detection limits were evaluated to be as low as 0.0044, 0.012, and 0.016 mg L^-1, respectively. Finally, a novel electrochemical analytical platform is successfully fabricated for the simultaneous monitoring of hydroquinone, catechol, and resorcinol with high sensitivity. When used for real wastewater samples analysis, recovery ratio ranging from 94 to 108% with lower than 5% of relative standard deviation (RSD) values was achieved. This work proves a facile strategy to prepare morphology-controlled N-doped carbon-based material and demonstrates its high application potential for environmental monitoring and electrochemical analysis.

Electrochemical Detection of Dihydroxybenzene Isomers at a Pencil Graphite Based Electrode

In this work, an HB pencil electrode (HBPE) was electrochemically modified by amino acids (AAs) glycine (GLY) and aspartic acid (ASA) and designated as GLY-HB and ASA-HB electrodes. They were used in the detection of dihydroxybenzene isomers (DHBIs) such as hydroquinone (HQ), catechol (CC), and resorcinol (RS), by cyclic voltammetry (CV), and by differential pulse voltammetry. HBPE was characterized by scanning electron microscopy and energy-dispersive X-ray spectroscopy. These three electrodes showed a linear relationship of current with concentration of DHBIs, and the electrochemical processes were diffusion controlled in all cases. In simultaneous detection, the limit of detection, based on signal-to-noise ratio (S/N = 3), for HQ, CC, and RS was 12.473, 16.132, and 25.25 μM, respectively, at bare HBPE; 5.498, 7.119, and 14.794 μM, respectively, at GLY-HB; and 22.459, 25.478, and 38.303 μM, respectively, at ASA-HB. The sensitivity for HQ, CC, and RS was 470.481, 363.781, and 232.416 μA/mM/cm², respectively, at bare HBPE; 364.785, 282.712, and 135.560 μA/mM/cm², respectively, at GLY-HB; and 374.483, 330.108, and 219.574, respectively, at ASA-HB. The interference studies clarified the suitability and reliability of the electrodes for the detection of HQ, CC, and RS in an environmental system. Real sample analysis was done using tap water, and the proposed electrodes expressed recovery with high reproducibility. Meanwhile, these three electrodes have excellent sensitivity and selectivity, which can be used as a promising technique for the detection of DHBIs simultaneously.

Design of imprinting matrix for dual template sensing via electropolymerized polythiophene films

This work presents the design of 3-thiophene acetic acid (3-TAA) polymer matrix based molecularly imprinted polymer (MIP)/reduced graphene oxide (RGO) composite for sensitive and selective detection of antipyrine (AnP) and ethionamide (ETH) simultaneously. Dual drug embedded molecularly imprinted polymer (MIP) based electrochemical sensor was developed via electropolymerization of 3-TAA. AnP and ETH were embedded inside a polymer matrix based on their 3-D orientation and interaction(s) with functional monomer(s). Their extraction from polymeric matrix generates cavities complimentary to shape and size of AnP and ETH. The extraction of templates was confirmed by differential pulse voltammetry (DPV) as well as high-performance liquid chromatography (HPLC). The designed sensor selectively captures and produces the electrochemical signal for imprinted drugs. The electrochemical behaviour of AnP and ETH was investigated by DPV technique. The sensitivity for both drug molecules was commendable on a single polymeric composite with RGO on GC electrode (LOD of 0.117 μM for AnP and 0.15 μM for ETH). Also, the sensor exhibited excellent selectivity towards AnP and ETH in the presence of other analogous interferent molecules. Thus, the designed sensor showed high sensitivity as well as high selectivity for imprinted dual drug molecules on a single platform.

Picomolar level electrochemical detection of hydroquinone, catechol and resorcinol simultaneously using a MoS2 nano-flower decorated graphene

A Graphene-Molybdenum disulphide nanocomposite was developed for the simultaneous electrochemical detection of dihydroxy benzene isomers attributed to the structural aspects.