Density Functional Theory Study of NiFeCo Trinary Oxy-Hydroxides for an Efficient and Stable Oxygen Evolution Reaction Catalyst

Evaluation of electrosynthesized reduced graphene oxide-Ni/Fe/Co-based (oxy)hydroxide catalysts towards the oxygen evolution reaction

In this work, the specific role of the addition of graphene oxide (GO) to state-of-the-art nickel-iron (NiFe) and cobalt-nickel-iron (CoNiFe) mixed oxides/hydroxides towards the oxygen evolution reaction (OER) is investigated. Morphology, structure, and OER catalytic activity of the catalysts with and without GO were studied. The catalysts were fabricated via a two-step electrodeposition. The first step included the deposition of GO flakes, which, in the second step, were reduced during the simultaneous deposition of NiFe or CoNiFe. As a result, NiFe-GO and CoNiFe-GO were fabricated without any additives directly on the nickel foam substrate. A significant improvement of the OER activity was observed after combining NiFe with GO (OER overpotential η(10 mA·cm^-2): 210 mV) compared to NiFe (η: 235 mV) and GO (η: 320 mV) alone. A different OER activity was observed for CoNiFe-GO. Here, the overall catalytic activity (η: 230 mV) increased compared to GO alone. However, it was reduced in comparison to CoNiFe (η: 224 mV). The latter was associated with the change in the morphology and structure of the catalysts. Further OER studies showed that each of the catalysts specifically influenced the process. The improvement in the OER by NiFe-GO results mainly from the structure of NiFe and the electroactive surface area of GO.

Wet Catalytic Oxidation of a FeMnCe-Activated Semi-Coke Catalyst for Treating Piperazine Wastewater

A FeMnCe-activated semi-coke catalyst (FeMnCe/ASC) was prepared by the co-precipitation method using semi-coke as the raw material. The structure and morphology were characterized by X-ray diffraction, Brunauer-Emmett-Teller, scanning electron microscopy, and transmission electron microscopy analyses. The catalytic activity and stability of the FeMnCe/ASC catalyst were investigated with piperazine as the target degradation pollutant and ammonia nitrogen and chemical oxygen demand (COD) as the evaluation indexes. The results showed that the average pore size of FeMnCe/ASC mesopores was 6.68 nm, and the active components were uniformly dispersed on the carrier surface. Under the optimum conditions of piperazine solution including a mass concentration of 100 mg/L, a catalyst mass concentration of 4.0 g/L, a reaction temperature of 240 °C, an oxygen partial pressure of 1.2 MPa, a stirring speed of 500 rpm, and a reaction time of 120 min, the degradation rates of both ammonia nitrogen and COD reached 100%. After the catalyst was recycled five times, the degradation rates of ammonia nitrogen and COD still reached more than 90%. The elemental valence changes before and after the reaction were analyzed by X-ray photoelectron spectroscopy, and the intermediate products generated from piperazine degradation were analyzed by gas chromatography-mass spectroscopy to evaluate the mechanism of piperazine degradation and speculate about the degradation pathway of piperazine.

Kinetic analysis of p-rGO/n-TiO2 nanocomposite generated by hydrothermal technique for simultaneous photocatalytic water splitting and degradation of methylene blue dye

In this study, the nanocomposites of reduced graphene oxide/TiO₂ (rGO/TiO₂ with different percentages) have been synthesized using a modified Hummers' method followed by hydrothermal treatment. The morphology and bonding structure of the prepared samples have been characterized by Fourier-transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffractometry (XRD), and X-ray photoelectron spectroscopy (XPS). The photo-characteristic aspects of the prepared samples have been indicated by photoluminescence (PL) emission spectroscopy and ultraviolet-visible diffuse reflection spectroscopy (DRS). The photocatalytic performance of rGO/TiO₂ demonstrated that it is an effective photocatalyst for methylene blue (MB) dye decomposition through illumination by a mercury lamp. Within 60 min of continuous irradiation, the nanocomposite-induced MB decomposition reached a rate of over 99%. Different MB concentrations and optimal percent loadings in catalysts have been investigated. Furthermore, the results showed that as the amount of catalyst increased, the decomposition of MB enhanced. Finally, the loading percentage of rGO with TiO₂ has been studied, and an empirical equation relating the reaction rate constant until the mass of the photocatalyst and dye concentration has been proposed. The results showed that the prepared nanocomposites had good photocatalytic activity toward water splitting and photo-decomposition of MB.

One-Dimensional CoMoP Nanostructures as Bifunctional Electrodes for Overall Water Splitting

As high-quality substitutes for conventional catalysts, the bifunctional catalytic properties of the coating of transition-metal-based materials are pivotal for improving water-splitting efficiency. Herein, cobalt-molybdenum bimetallic phosphide nanofibers (CoMoP NFs) were synthesized via a series of facile strategies, which are divided into pyrolysis electrospun PAN and metal salts, to obtain one-dimensional morphology and a gas-solid phosphating precursor. The obtained CoMoP NFs catalyst has superior catalytic activity performance in 1M KOH. Serving as an oxygen evolution reaction (OER) catalyst, the electrode of the CoMoP NFs affords different kinds of current densities at 50 mA cm^-2 and 100 mA cm^-2, with low overpotentials of 362 and 391 mV, respectively. In addition, the hydrogen evolution reaction (HER) performance of the CoMoP NFs mainly shows when under a low overpotential of 126 mV, which can deliver a current density of 10 mA cm^-2. In order to further detect the stability of the catalyst, we used multiple cyclic voltammetry and chronopotentiometry tests for OERs and HERs, which maintain performance and carry a current density of 10 mA cm^-2 for longer. As an integrated high-performance bifunctional electrode for overall water splitting, the CoMoP NFs only require 1.75 V@10 mA cm^-2 for 40 h. This work highlights a facile method to create an electrocatalyst with fiber nanostructures which possesses excellent activity as an alkaline electrolyte.

Highly Active Ni–Fe Based Oxide Oxygen Evolution Reaction Electrocatalysts for Alkaline Anion Exchange Membrane Electrolyser

Oxygen evolution reaction (OER) electrocatalysts are pivotal for sustainable hydrogen production through anion exchange membrane electrolysis. Cost-effective transition metals such as nickel and iron-based oxides (Ni–Fe–Ox) have been recognized as viable catalysts for the oxygen evolution process in alkaline media. In this work, we study the electrochemical characterization and stability of the Ni–Fe–Ox to find the suitability for AEM electrolysis. The results indicate that Ni–Fe–Ox has 5 times higher activity than pure Ni. The Ni–Fe–Ox electrodes exhibit an exceptionally high catalytic activity of 22 mA cm−2 at 1.55 V vs. RHE, and a Tafel value as low as 97 dec−1, for OER to occur. These findings imply that OER occurs at similar places along the Ni–Fe–Ox interface and that the Ni—Fe2O3 contact plays a significant role as the OER active site. Furthermore, it is also worth noting that the presence of metallic Ni allows for fast electron transit within the interface, which is necessary for successful electrocatalysis. Aside from the excellent OER performance, the exfoliated Ni–Fe–Ox demonstrated great stability with almost constant potential after 10 h of electrolysis at a current density of 10 mA cm−2. This work confirms Ni–Fe–Ox is a promising, highly efficient and cost-effective OER catalyst for AEM electrolysis.

Efficient fish-scale CeO2/NiFeCo composite material as electrocatalyst for oxygen evolution reaction

An electrochemical catalyst with efficient, stable, inexpensive energy storage for oxygen evolution and hydrogen evolution has raised global concerns on energy, calling for high-performance materials for effective treatments. In this paper, novel amorphous polymetallic doped CeO₂particles were prepared for an electrochemical catalyst via homogeneous phase precipitation at room temperature. Metal ions can be easily embedded into the oxygen vacancies formed by CeO₂, and the the electron transport capacity of the CeO₂/NiFeCo electrocatalyst is improved owing to the increase in active sites. In addition, the amorphous CeO₂/NiFeCo composite material is in a metastable state and will transform into different active states in a reducing or oxidizing environment. Furthermore, the amorphous material drives oxygen evolution reaction (OER) through the lattice oxygen oxidation mechanism (LOM), while LOM can effectively bypass the adsorption of strongly related intermediates in the adsorbate release mechanism, thus promoting OER procedure in a timely manner. As a result, CeO₂/NiFeCo exhibits a lower oxygen evolution overpotential of 260 mV at 10 mA cm^-2current density, which shows a predatorily competitive advantage compared with commercially available RuO₂and the reported catalysts.

Bismuth-Graphene Nanohybrids: Synthesis, Reaction Mechanisms, and Photocatalytic Applications—A Review

Photocatalysis is a classical solution to energy conversion and environmental pollution control problems. In photocatalysis, the development and exploration of new visible light catalysts and their synthesis and modification strategies are crucial. It is also essential to understand the mechanism of these reactions in the various reaction media. Recently, bismuth and graphene’s unique geometrical and electronic properties have attracted considerable attention in photocatalysis. This review summarizes bismuth-graphene nanohybrids’ synthetic processes with various design considerations, fundamental mechanisms of action, heterogeneous photocatalysis, benefits, and challenges. Some key applications in energy conversion and environmental pollution control are discussed, such as CO2 reduction, water splitting, pollutant degradation, disinfection, and organic transformations. The detailed perspective of bismuth-graphene nanohybrids’ applications in various research fields presented herein should be of equal interest to academic and industrial scientists.

Structural Characteristics and Environmental Applications of Covalent Organic Frameworks

Covalent organic frameworks (COFs) are emerging crystalline polymeric materials with highly ordered intrinsic and uniform pores. Their synthesis involves reticular chemistry, which offers the freedom of choosing building precursors from a large bank with distinct geometries and functionalities. The pore sizes of COFs, as well as their geometry and functionalities, can be pre-designed, giving them an immense opportunity in various fields. In this mini-review, we will focus on the use of COFs in the removal of environmentally hazardous metal ions and chemicals through adsorption and separation. The review will introduce basic aspects of COFs and their advantages over other purification materials. Various fabrication strategies of COFs will be introduced in relation to the separation field. Finally, the challenges of COFs and their future perspectives in this field will be briefly outlined.

Fe-Induced electronic optimization of mesoporous Co–Ni oxide nanosheets as an efficient binder-free electrode for the oxygen evolution reaction

An efficient binder-free OER electrode CoNiFeO_x/NF with mesoporous structure was synthesized by a facile strategy of hydrothermal method and post-annealing.

The Techno-Economic Benefit of Sorption Enhancement: Evaluation of Sorption-Enhanced Dimethyl Ether Synthesis for CO2 Utilization

Dimethyl ether (DME) is an important platform chemical and fuel that can be synthesized from CO2 and H2 directly. In particular, sorption-enhanced DME synthesis (SEDMES) is a novel process that uses the in situ removal of H2O with an adsorbent to ensure high conversion efficiency in a single unit operation. The in situ removal of steam has been shown to enhance catalyst lifetime and boost process efficiency. In addition, the hydrogen may be supplied through water electrolysis using renewable energy, making it a promising example of the (indirect) power-to-X technology. Recently, major advances have been made in SEDMES, both experimentally and in terms of modeling and cycle design. The current work presents a techno-economic evaluation of SEDMES using H2 produced by a PEM electrolyzer. A conceptual process design has been made for the conversion of CO2 and green H2 to DME, including the purification section to meet ISO fuel standards. By means of a previously developed dynamic cycle model for the SEDMES reactors, a DME yield per pass of 72.4 % and a carbon selectivity of 84.7% were achieved for the studied process design after optimization of the recycle streams. The production costs for DME by the power-to-X technology SEDMES process at 23 kt/year scale are determined at ∼€1.3 per kg. These costs are higher than the current market price but lower than the cost of conventional DME synthesis from CO2. Factors with the highest impact on the business cases are the electricity and CO2 cost price as well as the CAPEX of the electrolyzer, which is considered an important component for technology development. Furthermore, as the H2 cost constitutes the largest part of the DME production cost, SEDMES is demonstrated to be a powerful technology for efficient conversion of green H2 into DME.