Aldehyde-Functionalized Magnetic Particles to Capture Off-Target Chemotherapeutic Agents

Sulfonated Azocalix[4]arene-Modified Metal-Organic Framework Nanosheets for Doxorubicin Removal from Serum

Chemotherapy is one of the most commonly used methods for treating cancer, but its side effects severely limit its application and impair treatment effectiveness. Removing off-target chemotherapy drugs from the serum promptly through adsorption is the most direct approach to minimize their side effects. In this study, we synthesized a series of adsorption materials to remove the chemotherapy drug doxorubicin by modifying MOF nanosheets with sulfonated azocalix[4]arenes. The strong affinity of sulfonated azocalix[4]arenes for doxorubicin results in high adsorption strength (Langmuir adsorption constant = 2.45-5.73 L mg-1) and more complete removal of the drug. The extensive external surface area of the 2D nanosheets facilitates the exposure of a large number of accessible adsorption sites, which capture DOX molecules without internal diffusion, leading to a high adsorption rate (pseudo-second-order rate constant = 0.0058-0.0065 g mg-1 min-1). These adsorbents perform effectively in physiological environments and exhibit low cytotoxicity and good hemocompatibility. These features make them suitable for removing doxorubicin from serum during "drug capture" procedures. The optimal adsorbent can remove 91% of the clinical concentration of doxorubicin within 5 min.

A 3D-printed PCL/PEI/DNA bioactive scaffold for chemotherapy drug capture in vivo

Systemic chemotherapy after surgery is necessary to control tumor recurrence, but the severe side effects caused by chemotherapeutic drugs pose a great threat to patients' health. In this study, we originally develop a porous scaffold used for chemotherapy drug capture by using 3D printing technology. The scaffold is mainly composed of poly (ε-caprolactone) (PCL) and polyetherimide (PEI) with a mass ratio of 5/1. Subsequently, the printed scaffold is modified with DNA through the strong electrostatic integration between DNA and PEI to endow the scaffold with the specific absorption to doxorubicin (DOX, a widely used chemotherapy drug). The results show that pore diameter has an important influence on DOX adsorption, and smaller pores will ensure a higher DOX absorption. In vitro, the printed scaffold can absorb about 45 % DOX. While in vivo, it remains a higher absorption ability to DOX when the scaffold is successfully implanted into the common jugular vein of rabbits. What's more, the scaffold has good hemocompatibility and biocompatibility, indicating its safety for in vivo application. Taken together, the 3D-printed scaffold with excellent capture of chemotherapy drugs will play an important role in reducing the toxic side effects of chemotherapy drugs and improving the life quality of patients.

Self-Healing Chitosan Hydrogels: Preparation and Rheological Characterization

The paper aims at the preparation of chitosan self-healing hydrogels, designed as carriers for local drug delivery by parenteral administration. To this aim, 30 hydrogels were prepared using chitosan and pyridoxal 5-phosphate (P5P), the active form of vitamin B6 as precursors, by varying the ratio of glucosamine units and aldehyde on the one hand and the water content on the other hand. The driving forces of hydrogelation were investigated by nuclear magnetic resonance (NMR), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction, and polarized light microscopy (POM) measurements. NMR technique was also used to investigate the stability of hydrogels over time, and their morphological particularities were assessed by scanning electron microscopy (SEM). Degradability of the hydrogels was studied in media of four different pH, and preliminary self-healing ability was visually established by injection through a syringe needle. In-depth rheological investigation was conducted in order to monitor the storage and loss moduli, linear viscoelastic regime, and structural recovery capacity. It was concluded that chitosan crosslinking with pyridoxal 5-phosphate is a suitable route to reach self-healing hydrogels with a good balance of mechanical properties/structural recovery, good stability over time, and degradability controlled by pH.

Chitosan crosslinking with pyridoxal 5-phosphate vitamer toward biocompatible hydrogels for in vivo applications

Vitamin B6 is an essential micronutrient in the mammalian diet, with role of coenzyme and synergistic effect with some antibiotics and antitumor drugs. Based on these, we hypothesized that its use for the preparation of hydrogels can yield multifunctional biomaterials suitable for in vivo applications. To this aim, chitosan was reacted with the active form of vitamin B6, pyridoxal 5-phosphate, via acid condensation, when clear hydrogels were obtained. Their investigation by structural characterization methods proved that the hydrogelation was a consequence of both covalent imine formation and physical interactions. The novel hydrogels had microporous morphology and showed shrinking effect in phosphate buffer, indicating good shape preservation and slow dissolution in in vivo environment. Their enzymatic biodegradation could be controlled by the imination degree, varying from 40 to 61% in 21 days. They demonstrated very good in vitro cytocompatibility on normal human dermal fibroblasts cells and no harmful effect on experimental mice, confirming their safely use for in vivo application.

3D-Printed Drug Capture Materials Based on Genomic DNA Coatings

The toxic side effects of chemotherapy have long limited its efficacy, prompting expensive and long-drawn efforts to develop more targeted cancer therapeutics. An alternative approach to mitigate off-target toxicity is to develop a device that can sequester chemotherapeutic agents from the veins that drain the target organ before they enter systemic circulation. This effectively localizes the chemotherapy to the target organ, minimizing any hazardous side effects. 3D printing is ideal for fabricating these devices, as the geometric control afforded allows us to precisely dictate its hemodynamic performance in vivo. However, the existing materials compatible with 3D printing do not have drug-binding capabilities. Here, we report the stable coating of genomic DNA on a 3D-printed structure for the capture of doxorubicin. Genomic DNA is an effective chemotherapeutic-agent capture material due to the intrinsic DNA-targeting mechanism of action of these drugs. Stable DNA coatings were achieved through a combination of electrostatic interactions and ultraviolet C (UVC, 254 nm) cross-linking. These UVC cross-linked DNA coatings were extremely stable-leaching on average 100 pg of genomic DNA per mm2 of 3D-printed structure over a period of 30 min. In vitro studies of these materials in phosphate buffered saline and human serum demonstrated that they were able to capture, on average, 72 and 60 ng of doxorubicin per mm2 of structure, respectively. The stability and efficacy of these genomic DNA-coated 3D-printed materials represent a significant step forward towards the translation of these devices to clinical applications for the potential improvement of chemotherapy treatment.