Implementation of Laser-Induced Anti-Stokes Fluorescence Power Cooling of Ytterbium-Doped Silica Glass

Optical cooling of a Yb-doped alumino-phosphosilicate fiber in air by -250 mK

Recent progress in the fabrication of Yb-doped silicate fibers with low concentration quenching and low background absorption loss has led to the demonstration of anti-Stokes-fluorescence cooling in several aluminosilicate compositions. This breakthrough is critical to combat deleterious thermal effects due to the quantum defect in fiber lasers and amplifiers. Since cooling efficiencies remain low (1-2.7%), it is paramount to engineer compositions that improve this metric. We report a silica fiber with a core glass heavily doped with aluminum and phosphorus that sets, to our knowledge, a few new records. This few-mode fiber (16-µm core) was cooled in air by -0.25 K from room temperature with ∼0.5 W of 1040-nm power. The measured cooling efficiency is 3.3% at low pump power and 2.8% at the power that produced maximum cooling. The critical quenching concentration inferred from the measured dependence of cooling on pump power and careful calibration of the pump absorption and saturation is 79 wt.%. The inferred background absorption loss is 15 dB/km. Together with the fiber's average Yb concentration of 4.2 wt.%, these metrics rank among the best reported in a silica glass.

Laser cooling ytterbium doped silica by 67 K from ambient temperature

Laser cooling of a 5 cm long, 1 mm diameter ytterbium doped (6.56×1025 ions/m3) silica rod by 67 K from room temperature was achieved. For the pump source, a 100 W level ytterbium fiber amplifier was constructed along with a 1032 nm fiber Bragg grating seed laser. Experiments were done in vacuum and monitored with the non-contact differential luminescence thermometry method. Direct measurements of the absorption spectrum as a function of temperature were made, to avoid any possible ambiguities from site-selectivity and deviations from McCumber theory at low temperature. This allowed direct computation of the cooling efficiency versus temperature at the pump wavelength, permitting an estimated heat lift of 1.42 W/m as the sample cooled from ambient temperature to an absolute temperature of 229 K.

Impact of site-selective spectroscopy on laser cooling parameter characterization

From laser design to optical refrigeration, experimentally measured fluorescence spectra are often utilized to obtain input parameters for predictive models. However, in materials that exhibit site-selectivity, the fluorescence spectra depend on the excitation wavelength employed to take the measurement. This work explores different conclusions that predictive models reach after inputting such varied spectra. Here, temperature-dependent site-selective spectroscopy is carried out on an ultra-pure Yb, Al co-doped silica rod fabricated by the modified chemical vapor deposition technique. The results are discussed in the context of characterizing ytterbium doped silica for optical refrigeration. Measurements made between 80 K and 280 K at several different excitation wavelengths yield unique values and temperature dependencies of the mean fluorescence wavelength. For the excitation wavelengths studied here, the variation in emission lineshapes ultimately lead to calculated minimum achievable temperatures (MAT) ranging between 151 K and 169 K, with theoretical optimal pumping wavelengths between 1030 nm and 1037 nm. Direct evaluation of the temperature dependence of the fluorescence spectra band area associated with radiative transitions out of the thermally populated ²F_5/2 sublevel may be a better approach to identifying the MAT of a glass where site-selective behavior precludes unique conclusions.

Potential of ytterbium doped silica glass for solid-state optical refrigeration to below 200 K

We report on the optical refrigeration of ytterbium doped silica glass by >40 K starting at room temperature, which represents more than a two-fold improvement over the previous state-of-the-art. A spectroscopic investigation of the steady-state and time-dependent fluorescence was carried out over the temperature range 80 K to 400 K. The calculated minimum achievable temperature for our Yb³⁺ doped silica sample is ≈150 K, implying the potential for utilizing ytterbium doped silica for solid-state optical refrigeration below temperatures commonly achieved by standard Peltier devices.

Laser cooling experiments to measure the quantum efficiency of Yb-doped silica fibers

A detailed investigation into the wavelength-dependent cooling efficiencies of two ultra-pure large core diameter ytterbium-doped silica fibers is carried out by means of the laser-induced thermal modulation spectroscopy (LITMoS) method. From these measurements, an external quantum efficiency of 0.99 is obtained for both fibers. Optimal cooling is seen for pump wavelengths between 1032 and 1035 nm. The crossover wavelength from heating to cooling is identified to be between 1018 and 1021 nm. The fiber with higher Yb³⁺ ion density exhibits better cooling, seen by the input power normalized temperature differential.

Anti-Stokes fluorescence cooling of nanoparticle-doped silica fibers

The first observation of cooling by anti-Stokes pumping in nanoparticle-doped silica fibers is reported. Four Yb-doped fibers fabricated using conventional modified chemical vapor deposition (MCVD) techniques were evaluated, namely, an aluminosilicate fiber and three fibers in which the Yb ions were encapsulated in CaF₂, SrF₂, or BaF₂ nanoparticles. The nanoparticles, which oxidize during preform processing, provide a modified chemical environment for the Yb³⁺ ions that is beneficial to cooling. When pumped at the near-optimum cooling wavelength of 1040 nm at atmospheric pressure, the fibers experienced a maximum measured temperature drop of 20.5 mK (aluminosilicate fiber), 26.2 mK (CaF₂ fiber), and 16.7 mK (SrF₂ fiber). The BaF₂ fiber did not cool but warmed slightly. The three fibers that cooled had a cooling efficiency comparable to that of the best previously reported Yb-doped silica fiber that cooled. Data analysis shows that this efficiency is explained by the fibers' high critical quenching concentration and low residual absorptive loss (linked to sub-ppm OH contamination). This study demonstrates the large untapped potential of nanoparticle doping in the current search for silicate compositions that produce optimum anti-Stokes cooling.

Accurate Characterization of the Properties of the Rare-Earth-Doped Crystal for Laser Cooling

We present a method for calibrating a commercial thermal camera adopted to accurately measure the temperature change of the sample in a laser-induced temperature modulation spectrum (LITMoS) test, which is adopted for measuring two crucial parameters of the external quantum efficiency ηext and the background absorption coefficient αb for assessing the laser cooling grade of the rare-earth-doped materials. After calibration, the temperature resolution of the calibrated thermal camera is better than 0.1 K. For the cooling grade Czochralski-grown 5% Yb3+:LuLiF4 crystal, the corresponding values of ηext and αb are LITMoS = measured to be ηext=99.4 (±0.1)% and αb=1.5 (±0.1)×10−4 cm−1, respectively.

Laser cooling of a Yb doped silica fiber by 18 Kelvin from room temperature

An ytterbium doped silica optical fiber with a core diameter of 900µm has been cooled by 18.4 K below ambient temperature by pumping with 20 W of 1035 nm light in vacuum. In air, cooling by 3.6 K below ambient was observed with the same 20 W pump. The temperatures were measured with a thermal imaging camera and differential luminescence thermometry. The cooling efficiency is calculated to be 1.2±0.1%. The core of the fiber was codoped with Al³⁺ for an Al to Yb ratio of 6:1, to allow for a larger Yb concentration and enhanced laser cooling.