Development of Photosensitive Natural Rubber as a Mechanical Modifier for Ultraviolet-Curable Resin Applied in Digital Light Processing-Based Three-Dimensional Printing Technology

Mechanical Properties' Strengthening of Photosensitive 3D Resin in Lithography Technology Using Acrylated Natural Rubber

Acrylated natural rubber (ANR) with various acrylate contents (0.0-3.5 mol%) was prepared from natural rubber as a raw material and then incorporated with commercial 3D resin to fabricate specimens using digital light processing. As a result, the utilization of ANR with 1.5 mol% acrylate content could provide the maximum improvement in stretchability and impact strength, approximately 155% and 221%, respectively, over using pure 3D resin, without significant deterioration of tensile modulus and mechanical strength. According to evidence from a scanning electron microscope, this might be due to the partial interaction between the dispersed small rubber particles and the resin matrix. Additionally, the glass-transition temperature of the 3D-printed sample shifted to a lower temperature by introducing a higher acrylate content in the ANR. Therefore, this work might offer a practical way to effectively enhance the properties of the fundamental commercial 3D resin and broaden its applications. It also makes it possible to use natural rubber as a bio-based material in light-based 3D printing.

Soft Wearable Piezoresistive Sensors Based on Natural Rubber Fabricated with a Customized Vat-Based Additive Manufacturing Process

Piezoresistive sensors for monitoring human motions are essential for the prevention and treatment of injury. Natural rubber is a material of renewable origin that can be used for the development of soft wearable sensors. In this study, natural rubber was combined with acetylene black to develop a soft piezoresistive sensing composite for monitoring the motion of human joints. An additive manufacturing technique based on stereolithography was used, and it was seen that the sensors produced with the method could detect even small strains (<10%) successfully. With the same sensor composite fabricated by mold casting, it was not possible to detect low strains reliably. TEM microscopy revealed that the distribution of the filler was not homogeneous for the cast samples, suggesting a directionality of the conductive filler network. For the sensors fabricated through the stereolithography-based method, a homogeneous distribution could be achieved. Based on mechano-electrical characterization, it was seen that the samples produced with AM combined the ability to endure large elongations with a monotonic sensor response. Under dynamic conditions, the sensor response of the samples produced by 3D printing showed lower drift and lower signal relaxation. The piezoresistive sensors were examined for monitoring the motion of the human finger joints. By increasing the bending angle of the sensor, it was possible to increase the sensitivity of the response. With the renewable origin of natural rubber and manufacturing method, the featured sensors can expand the applicability of soft flexible electronics in biomedical applications and devices.

3D printing of bone and cartilage with polymer materials

Damage and degeneration to bone and articular cartilage are the leading causes of musculoskeletal disability. Commonly used clinical and surgical methods include autologous/allogeneic bone and cartilage transplantation, vascularized bone transplantation, autologous chondrocyte implantation, mosaicplasty, and joint replacement. 3D bio printing technology to construct implants by layer-by-layer printing of biological materials, living cells, and other biologically active substances in vitro, which is expected to replace the repair mentioned above methods. Researchers use cells and biomedical materials as discrete materials. 3D bio printing has largely solved the problem of insufficient organ donors with the ability to prepare different organs and tissue structures. This paper mainly discusses the application of polymer materials, bio printing cell selection, and its application in bone and cartilage repair.

Three-Dimensional Printing Materials for Cultural Innovation Products of Historical Buildings

Innovation products from historical cultural architectural have widely adopted 3D printing technology in recent years. To study the applicability of existing 3D printing materials, it is necessary to analyze the performance indicators of 3D printing materials and carry out material science experiments. Step 1: the material performance index composition of cultural innovation products was derived by integrating the literature of cultural heritage, product design, quality system, and material science. Step 2: The columns of Chengs’ Miyake in Huizhou were taken as the creative source. Its geometric shape model was obtained through 3D scanning, and the design of the cultural innovation products was completed. Step 3: Photosensitive resin, nylon, and stainless steel, three commonly used 3D printing materials, were used to make samples, with one sample of each material. Finally, we carried out material science tests according to the material performance index. The experimental data of three materials were obtained and compared. The properties of the three 3D printing materials, photosensitive resin, nylon, and stainless steel, have advantages and disadvantages. Still, they all struggle to meet the needs of cultural and creative products in historical buildings. It is necessary to integrate the three materials’ properties to develop new 3D printing materials.