Toward Reducing Surfactant Adsorption on Clay Minerals by Lignin for Enhanced Oil Recovery Application

Colloidal and Thermal Stability of Three-Component Hybrid Materials Containing Clay Mineral, Polysaccharide and Surfactant

The paper presents the colloidal and thermal stability of the three-component hybrid materials containing halloysite, polysaccharides (alginic acid, cationic cellulose and hydroxyethyl cellulose) and Tritons. TX-100, TX-165 and TX-405 were used as non-ionic surfactants. Stability and other properties of the hybrid materials were tested by the following methods: UV-Vis, TGA (thermogravimetric analysis) and DSC (differential scanning calorimetry), CHN (elemental analysis), SEM-EDX (scanning electron microscopy with energy dispersive X-ray spectroscopy) and tensiometry. According to the results with the increasing polymer concentration the colloidal stability of the tested systems also increases. Moreover, the addition of the surfactants causes the increase of polysaccharide adsorption but the colloidal stability of the tested systems decreases due to large weights of formed aggregates. As follows from the thermal analysis, the comparison of the TG/DTG-DSC curves obtained for the investigated polymers confirms that their thermal decomposition courses have some common features. The obtained results have the application potential in the formation of the materials for the pollutants removal from water and sewages.

Pillarization of Sumatera Bentonite by Sodium-assisted As Effective Adsorbent of Anionic Surfactants Sodium Lauryl Sulphate (SLS) Waste

In this work, the Sumatera bentonite was sodium-pillarized in a new low-temperature and restricted time preparation route and then applied in anionic surfactant sodium lauryl sulphate removal. Structure characterization used Fourier Transform Infra Red (FT-IR), Scanning Electron Microscope - Energy Dispersive X-ray (SEM-EDX), X-ray Diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. A strong peak at 22° and 35.66° in XRD analysis was detected as Sodium-pillar that increased crystallinity, then the functional changes of dehydration in lattice structure were detected in 1013 cm−1 by FTIR analysis. The morphology and compositional transformation were analyzed by SEM-EDX and BET analysis, denoted by increasing particle shape and sodium intercalant composition homogeneity. Moreover, the surface area increased from 61.791 to 66.086 m2/g. The sodium lauryl sulphate adsorption by bentonite-Na reached maximum capacity at 8.403 mg/g, which is higher than the pristine bentonite (5.747 mg/g) under the optimum condition. The adsorption mechanism is feasible, endothermic, and conformed to the pseudo-second-order and Freundlich adsorption model. The new route proposed for sodium intercalation effectively improves the Sumatera bentonite adsorption ability to remove sodium lauryl sulphate waste. Copyright © 2023 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Effect of Sulfate-Based Scales on Calcite Mineral Surface Chemistry: Insights from Zeta-Potential Experiments and Their Implications on Wettability

Scale formation and deposition in the subsurface and surface facilities have been recognized as a major cause of flow assurance issues in the oil and gas industry. Sulfate-based scales such as sulfates of calcium (anhydrite and gypsum) and barium (barite) are some of the commonly encountered scales during hydrocarbon production operations. Oilfield scales are a well-known flow assurance problem, which occurs mainly due to the mixing of incompatible brines. Researchers have largely focused on the rocks' petrophysical property modifications (permeability and porosity damage) caused by scale precipitation and deposition. Little or no attention has been paid to their influence on the surface charge and wettability of calcite minerals. Thus, this study investigates the effect of anhydrite and barite scales' presence on the calcite mineral surface charge and their propensity to alter the wetting state of calcite minerals. This was achieved vis-à-vis zeta-potential (ζ-potential) measurement. Furthermore, two modes of the scale control (slug and continuous injections) using ethylenediaminetetraacetic acid (EDTA) were examined to determine the optimal control strategy as well as the optimal inhibitor dosage. Results showed that the presence of anhydrite and barite scales in a calcite reservoir affects the colloidal stability of the system, thus posing a threat of precipitation, which would result in permeability and porosity damage. Also, the calcite mineral surface charge is affected by the presence of calcium and barium sulfate scales; however, the magnitude of change in the surface charge via ζ-potential measurement is insignificant to cause wettability alteration by the mineral scales. Slug and continuous injections of EDTA were implemented, with the optimal scale control strategy being the continuous injection of EDTA solutions. The optimal dosage of EDTA for anhydrite scale control is 5 and 1 wt % for the formation water and seawater environments, respectively. In the case of barite, in both environments, an EDTA dosage of 1 wt % suffices. Findings from this study not only further the understanding of the scale effects on calcite mineral systems but also provide critical insights into the potential of scale formation and their mechanisms of interactions for better injection planning and the development of a scale control strategy.