Polyethyleneimine-Modified Amorphous Silica for the Selective Adsorption of CO2/N2 at High Temperatures

Development and Characterization of Polyethylenimine-Infiltrated Mesoporous Silica Foam Pellets for CO2 Capture

Polyethylenimine (PEI) has been shown to be promising for direct air capture (DAC) of carbon dioxide and has potential for commercial scale-up globally. Laboratory scale processes include multiple steps, such as mixing, solvent extraction, vacuum application, sonication, and various flushes and activation steps. It is critical to properly control these operating parameters to achieve higher capture capacity as a result of the optimized material configuration. This study adopts previously published pelletization processes for PEI-infiltrated mesoporous foam silica (mesoporous silica foam) to uncover the adsorption mechanisms and optimize the associated fabrication steps, such as sonication, to achieve higher sorbent productivity. A high capture capacity was achieved at 46 °C for 75 wt % PEI loading (2.27 mmol/g) followed by PEI_MSF 70 (1.81 mmol/g) and PEI_MSF 80 (1.44 mmol/g). As part of the optimization, sonication parameters of frequency, amplitude, and time were modified for PEI_MSF 75 sorbent, which resulted in the highest uptake capacity of 3.04 mmol/g (sonicated at 40 kHz and a wave amplitude of 50% for 30 s). These preliminary results would tend to prove that sonication energy affects carbon capture capacity, although there is still a lack of understanding regarding the exact underlying mechanism, suggesting the need for further investigation. It is important to note that the present work is focused on the adsorption mechanisms and not desorption or durability of the capture performance. Ongoing research addresses these factors. This paper is intended to establish baseline DAC behavior of a promising capture medium and begins probing the optimization spectrum by considering the effects of sonication energy on adsorption. Ongoing work intends to address potential abbreviations of the full range of process steps and furthers the understanding of kinetics by considering the desorption and resorption attributes.

Fabrication of Highly Efficient ZIF-8@PEI Monoliths for CO2 Capture Using Phosphorylated Cellulose Nanofiber as a Binder

This study involves the synthesis and comparison of zeolitic imidazolate frameworks (ZIFs), specifically ZIF-8 and ZIF-67 pristine with a commercial zeolite, emphasizing their CO2 affinity and sorption capability. To overcome challenges persisting in the handling and integration of these materials into industrial adsorption processes, particularly when limited to microcrystalline fine powders, we present herein an innovative manufacturing method to produce standalone monolithic supports. This process involves pseudoplastic paste formulations utilizing polyethylenimine (PEI) as a coagulant and locally fabricated phosphorylated cellulose nanofiber (PCNF) as a binding agent. Rheological investigation was conducted to anticipate the required shaping and design by means of paste flowability, consistency, and stiffness. XRD and FTIR results confirm the preservation of crystalline structure and the occurrence of amine functionalization associated with the presence of PEI, respectively. The proposed method significantly enhances the CO2 adsorption performance of the produced ZIF-8 monolith in comparison with that reached when using the pristine material, achieving a capacity of 1.25-2 mmol·g-1 at 30 °C under dry conditions in a pressure range of 1-13 bar, respectively. In other words, this work clearly highlights an effective applicability of the ZIF-8 monolith as an innovative sorbent for further designing CO2 capture industrial setups.

Facile fabrication of temperature/pH dual sensitive hydrogels based on cellulose and polysuccinimide through aqueous amino-succinimide reaction

A temperature/pH dual sensitive hydrogel with a semi-interpenetrating network (semi-IPN) structure was synthesized through an aqueous amino-succinimide reaction between water-soluble polysuccinimide and polyethyleneimine in the presence of thermosensitive cellulose derivatives. Single-factor experiments were carried out to optimize the preparation conditions of the semi-IPN hydrogel. The swelling behavior and cytotoxicity assay of the hydrogel were tested. Finally, taking 5- fluorouracil (5-Fu) as a model drug, the release performance of the 5-Fu-loaded hydrogel was investigated. The results indicated that the swelling ratio (SR) first decreased and then increased when the pH of the solutions ascended from 2 to 10. The SR decreased with the increase in temperature. In addition, the swelling behavior of the hydrogel was reversible and reproducible under different pH values and temperatures. The prepared hydrogels had good cytocompatibility. The release behavior of 5-Fu was most consistent with the Korsmeyer-Peppas model and followed the case II diffusion. The acidic environment was beneficial for the release of 5-Fu. The preparation process of the semi-IPN hydrogel is simple and the reaction can proceed quickly in water. The strategy introduced here has great potential for application in the preparation of drug carriers.

Three-Dimensional Cross-Linking Network Coating for the Flame Retardant of Bio-Based Polyamide 56 Fabric by Weak Bonds

Weak bonds usually make macromolecules stronger; therefore, they are often used to enhance the mechanical strength of polymers. Not enough studies have been reported on the use of weak bonds in flame retardants. A water-soluble polyelectrolyte complex composed of polyethyleneimine (PEI), sodium tripolyphosphate (STPP) and melamine (MEL) was designed and utilized to treat bio-based polyamide 56 (PA56) by a simple three-step process. It was found that weak bonds cross-linked the three compounds to a 3D network structure with MEL on the surface of the coating under mild conditions. The thermal stability and flame retardancy of PA56 fabrics were improved by the controlled coating without losing their mechanical properties. After washing 50 times, PA56 still kept good flame retardancy. The cross-linking network structure of the flame retardant enhanced both the thermal stability and durability of the fabric. STPP acted as a catalyst for the breakage of the PA56 molecular chain, PEI facilitated the char formation and MEL released non-combustible gases. The synergistic effect of all compounds was exploited by using weak bonds. This simple method of developing structures with 3D cross-linking using weak bonds provides a new strategy for the preparation of low-cost and environmentally friendly flame retardants.

Unlocking High-Current Performance in Silicon Anode: Synergistic Phosphorus Doping and Nitrogen-Doped Carbon Encapsulation to Enhance Lithium Diffusivity

The silicon (Si) offers enormous theoretical capacity as a lithium-ion battery (LIB) anode. However, the low charge mobility in Si particles hinders its application for high current loading. In this study, ball-milled phosphorus-doped Si nanoparticles encapsulated with nitrogen-doped carbon (P-Si@N-C) are employed as an anode for LIBs. P-doped Si nanoparticles are first obtained via ball-milling and calcination of Si with phosphoric acid. N-doped carbon encapsulation is then introduced via carbonization of the surfactant-assisted polymerization of pyrrole monomer on P-doped Si. While P dopant is required to support the stability at high current density, the encapsulation of Si particles with N-doped carbon is influential in enhancing the overall Li+ diffusivity of the Si anode. The combined approaches improve the anode's Li+ diffusivity up to tenfold compared to the untreated anode. It leads to exceptional anode stability at a high current, retaining 87 % of its initial capacity under a large current rate of 4000 mA g-1. The full-cell comprising P-Si@N-C anode and LiFePO4 cathode demonstrates 94 % capacity retention of its initial capacity after 100 cycles at 1 C. This study explores the effective strategies to improve Li+ diffusivity for high-rate Si-based anode.

Interfacial Triboelectricity Lights Up Phosphor-Polymer Elastic Composites: Unraveling the Mechanism of Mechanoluminescence in Zinc Sulfide Microparticle-Embedded Polydimethylsiloxane Films

Composites comprising copper-doped zinc sulfide phosphor microparticles embedded in polydimethylsiloxane (ZnS:Cu-PDMS) have received significant attention over the past decade because of their bright and durable mechanoluminescence (ML); however, the underlying mechanism of this unique ML remains unclear. This study reports empirical and theoretical findings that confirm this ML is an electroluminescence (EL) of the ZnS:Cu phosphor induced by the triboelectricity generated at the ZnS:Cu microparticle-PDMS matrix interface. ZnS:Cu microparticles that exhibit bright ML are coated with alumina, an oxide with strong positive triboelectric properties; the contact separation between this oxide coating and PDMS, a polymer with strong negative triboelectric properties, produces sufficient interfacial triboelectricity to induce EL in ZnS:Cu microparticles. The ML of ZnS:Cu-PDMS composites varies on changing the coating material, exhibiting an intensity that is proportional to the amount of interfacial triboelectricity generated in the system. Finally, based on these findings, a mechanism that explains the ML of phosphor-polymer elastic composites (interfacial triboelectric field-driven alternating-current EL model) is proposed in this study. It is believed that understanding this mechanism will enable the development of new materials (beyond ZnS:Cu-PDMS systems) with bright and durable ML.