Piezoelectric Property Enhancement of PZT/Poly(vinylidenefluoride-co-trifluoroethylene) Hybrid Films for Flexible Piezoelectric Energy Harvesters

Self-Reinforced Piezoelectric Response of an Electroluminescent Film for the Dual-Channel Signal Monitoring of Damaged Areas

Organic piezoelectric nanogenerators (PENGs) show promise for monitoring damage in mechanical equipment. However, weak interfacial bonding between the reinforcing phase and the fluorinated material limits the feedback signal from the damaged area. In this study, we developed a PENG film capable of real-time identification of the damage location and extent. By incorporating core-shell barium titanate (BTO@PVDF-HFP) nanoparticles, we achieved enhanced piezoelectric characteristics, flexibility, and processability. The composite film exhibited an expanded output voltage range, reaching 41.8 V with an increase in frequency, load, and damage depth. Additionally, the film demonstrated self-powered electroluminescence (EL) during the wear process, thanks to its inherent ferroelectric properties and the presence of luminescent ZnS:Cu particles. Unlike conventional PENG electroluminescent devices, the PENG film exhibited luminescence at the damage location over a wide temperature range. Our findings offer a novel approach for realizing modular and miniaturized real-time damage mapping systems in the field of safety engineering.

Self-Polarized P(VDF-TrFE)/Carbon Black Composite Piezoelectric Thin Film

Self-polarized energy harvesting materials have seen increasing research interest in recent years owing to their simple fabrication method and versatile application potential. In this study, we systematically investigated self-polarized P(VDF-TrFE)/carbon black (CB) composite thin films synthesized on flexible substrates, with the CB content varying from 0 to 0.6 wt.% in P(VDF-TrFE). The presence of -OH functional groups on carbon black significantly enhances its crystallinity, dipolar orientation, and piezoelectric performance. Multiple characterization techniques were used to investigate the crystalline quality, chemical structure, and morphology of the composite P(VDF-TrFE)/CB films, which indicated no significant changes in these parameters. However, some increase in surface roughness was observed when the CB content increased. With the application of an external force, the piezoelectrically generated voltage was found to systematically increase with higher CB content, reaching a maximum value at 0.6 wt.%, after which the sample exhibited low resistance. The piezoelectric voltage produced by the unpoled 0.6 wt.% CB composite film significantly exceeded the unpoled pure P(VDF-TrFE) film when subjected to the same applied strain. Furthermore, it exhibited exceptional stability in the piezoelectric voltage over time, exceeding the output voltage of the poled pure P(VDF-TrFE) film. Notably, P(VDF_TrFE)/CB composite-based devices can be used in energy harvesting and piezoelectric strain sensing to monitor human motions, which has the potential to positively impact the field of smart wearable devices.

Graphene Nanoplatelet/Multiwalled Carbon Nanotube/Polypyrrole Hybrid Fillers in Polyurethane Nanohybrids with 3D Conductive Networks for EMI Shielding

This work reports the preparation of graphene nanoplatelet (GNP)/multiwalled carbon nanotube (MWCNT)/polypyrrole (PPy) hybrid fillers via in situ chemical oxidative polymerization with the addition of a cationic surfactant, hexadecyltrimethylammonium bromide. These hybrid fillers were incorporated into polyurethane (PU) to prepare GNP/MWCNT/PPy/PU nanohybrids. The electrical conductivity of the nanohybrids was synergistically enhanced by the high conductivity of the hybrid fillers. Furthermore, the electromagnetic interference (EMI) shielding effectiveness (SE) was greatly increased by interfacial polarization between the GNPs, MWCNTs, PPy, and PU. The optimal formulation for the preparation of GNP/MWCNT/PPy three-dimensional (3D) nanostructures was determined by optimization experiments. Using this formulation, we successfully prepared GNP/PPy nanolayers (two-dimensional) that are extensively covered by MWCNT/PPy nanowires (one-dimensional), which interconnect to form GNP/MWCNT/PPy 3D nanostructures. When incorporated into a PU matrix to form a nanohybrid, these 3D nanostructures form a continuous network of conductive GNP-PPy-CNT-PPy-GNP paths. The EMI SE of the nanohybrid is 35-40 dB at 30-1800 MHz, which is sufficient to shield over 99.9% of electromagnetic waves. Therefore, this EMI shielding material has excellent prospects for commercial use. In summary, a nanohybrid with excellent EMI SE performance was prepared using a facile and scalable method and was shown to have great commercial potential.

A hybrid microwave sintered PZT composite as a flexible piezoelectric nanogenerator

Interest in piezoelectric nanogenerators has grown extensively due to high piezoelectric coefficients. Piezoelectric ceramic-based devices have dominated research in large-scale energy harvesting. Morphotropic phase boundary PbZr_0.52Ti_0.48O₃ (MPB-PZT) synthesized using Hybrid Microwave Sintering (HMS) at a low temperature (940 °C) for 20 min has emerged as a dense ceramic. The Rietveld refinement studies confirm its dual phase (tetragonal (P4mm) and rhombohedral (R3m)). The PZT ceramic is exploited as a piezoelectric material, which can improve the output piezoelectric potential of a piezoelectric nanogenerator (PENG). Multi-walled carbon nanotubes (MWCNTs) are evenly distributed in the PZT composite to reduce the internal resistance of the PENG. According to the percolation theory, small amounts of MWCNTs dispersed within the composite ink can significantly improve the output voltage of the PENG by acting as conductive bridges between the polymer (polyvinylpyrrolidone (PVP)) and ceramic particles. The concentration of PZT and the amount of MWCNTs are changed to enhance the device's output voltage. As a result, an optimized PENG with a PZT (1.5 g)/MWCNT (0.06 wt%)/PVP (4 g) (PVP - polyvinylpyrrolidone) composite film is obtained. The PENGs are mechanically poled. The optimised output voltage of the PENG is 16 Vpp, which could light up a series of 20 commercial light emitting diodes (LEDs). The PENG is attached to footwear and is noticed to efficiently harvest energy from daily human activities which demonstrate its practical applications.

Synthesis of a nitrogen doped reduced graphene oxide based ceramic polymer composite nanofiber film for wearable device applications

In this study, piezoelectric composite nanofiber films were fabricated by introducing nitrogen-doped-reduced-graphene-oxide as a conductive material to a P(VDF-TrFE) polymer and a BiScO₃–PbTiO₃ ceramic composite employing an electrospinning process. Nitrogen was doped/substituted into rGO to remove or compensate defects formed during the reduction process. Electro-spinning process was employed to extract piezoelectric composite nanofiber films under self-poling condition. Interdigital electrodes was employed to make planner type energy harvesters to collect electro-mechanical energy applied to the flexible energy harvester. From the piezoelectric composite with interdigital electrode, the effective dielectric permittivity extracted from the conformal mapping method. By introducing BS–PT ceramics and N-rGO conductors to the P(VDF-TrFE) piezoelectric composite nanofiber films, the effective dielectric permittivity was improved from 8.2 to 15.5. This improved effective dielectric constant probably come from the increased electric flux density due to the increased conductivity. Fabricated interdigital electrode using this thin composite nanofiber film was designed and tested for wearable device applications. An external mechanical force of 350 N was applied to the composite nanofiber-based energy harvester with interdigital electrodes at a rate of 0.6 Hz, the peak voltage and current were 13 V and 1.25 μA, respectively. By optimizing the device fabrication, the open-circuit voltage, stored voltage, and generated output power obtained were 12.4 V, 3.78 V, and 6.3 μW, respectively.

Screen Printing of Surface-Modified Barium Titanate/Polyvinylidene Fluoride Nanocomposites for High-Performance Flexible Piezoelectric Nanogenerators

Piezoelectric energy harvesters are appealing for the improvement of wearable electronics, owing to their excellent mechanical and electrical properties. Herein, screen-printed piezoelectric nanogenerators (PENGs) are developed from triethoxy(octyl)silane-coated barium titanate/polyvinylidene fluoride (TOS-BTO/PVDF) nanocomposites with excellent performance based on the important link between material, structure, and performance. In order to minimize the effect of nanofiller agglomeration, TOS-coated BTO nanoparticles are anchored onto PVDF. Thus, composites with well-distributed TOS-BTO nanoparticles exhibit fewer defects, resulting in reduced charge annihilation during charge transfer from inorganic nanoparticles to the polymer. Consequently, the screen-printed TOS-BTO/PVDF PENG exhibits a significantly enhanced output voltage of 20 V, even after 7500 cycles, and a higher power density of 15.6 μW cm^-2, which is 200 and 150% higher than those of pristine BTO/PVDF PENGs, respectively. The increased performance of TOS-BTO/PVDF PENGs is due to the enhanced compatibility between nanofillers and polymers and the resulting improvement in dielectric response. Furthermore, as-printed devices could actively adapt to human movements and displayed excellent detection capability. The screen-printed process offers excellent potential for developing flexible and high-performance piezoelectric devices in a cost-effective and sustainable way.

Mitigating the Negative Piezoelectricity in Organic/Inorganic Hybrid Materials for High-performance Piezoelectric Nanogenerators

The conversion of ecofriendly waste energy into useable electrical energy is of significant interest for energy harvesting technologies. Piezoelectric nanogenerators based on organic/inorganic hybrid materials are a key promising technology for harvesting mechanical energy due to their high piezoelectric coefficient and good mechanical flexibility. However, the negative piezoelectric effect of the polymer component in composite devices severely undermines its overall piezoelectricity, compromising the output performance of PVDF-based piezoelectric hybrid nanogenerators. Here, to conquer this, we report a two-step poling schedule to orient the dipoles of organic and inorganic components in the same direction. The optimized nanogenerator delivers a combination of high piezoelectric coefficient, great output performance, and remarkable stability. The isotropic piezoelectricity in the composite device collaborates to output a maximum voltage of 110 V and a power density of 7.8 μW cm^-2. This strategy is also applied to elevate the piezoelectricity of other organic/inorganic-hybrid-based nanogenerators, substantiating its universal applicability for composite piezoelectric nanogenerators. This study presents a feasible strategy for enhancing the effective output capability of composite nanogenerator technologies.