Influence of Molecular Weight on Structure and Catalytic Characteristics of Ordered Mesoporous Carbon Derived from Lignin

Efficient isomerization of glucose into fructose by MgO-doped lignin-derived ordered mesoporous carbon

The conversion of glucose into fructose can transform cellulose into high-value chemicals. This study introduces an innovative synthesis method for creating an MgO-based ordered mesoporous carbon (MgO@OMC) catalyst, aimed at the efficient isomerization of glucose into fructose. Throughout the synthesis process, lignin serves as the exclusive carbon precursor, while Mg2+ functions as both a crosslinking agent and a metallic active center. This enables a one-step synthesis of MgO@OMC via a solvent-induced evaporation self-assembly (EISA) method. The synthesized MgO@OMCs exhibit an impeccable 2D hexagonal ordered mesoporous structure, in addition to a substantial specific surface area (378.2 m2/g) and small MgO nanoparticles (1.52 nm). Furthermore, this catalyst was shown active, selective, and reusable in the isomerization of glucose to fructose. It yields 41 % fructose with a selectivity of up to 89.3 % at a significant glucose loading of 7 wt% in aqueous solution over MgO0.5@OMC-600. This performance closely rivals the current maximum glucose isomerization yield achieved with solid base catalysts. Additionally, the catalyst retains a fructose selectivity above 60 % even after 4 cycles, a feature attributable to its extended ordered mesoporous structure and the spatial confinement effect of the OMCs, bestowing it with high catalytic efficiency.

Advancing mesoporous carbon synthesis for supercapacitors: a systematic investigation of cross-linking agent effects on pore structure and functionality

Soft-templating synthesis provides an effective route to prepare ordered mesoporous carbons (MCs) that can be used for supercapacitors. During this process, the cross-linking of carbon precursors is critical to obtain tailored pore structural MCs, thus careful selection of appropriate cross-linking agents is required. Despite the shift from the prevailing cross-linker formaldehyde to its more environmentally friendly alternatives, detailed understanding on the influence of different cross-linking agents on templating synthesis is still lacking. Therefore, it remains challenging to draw a conclusion regarding which cross-linker can effectively enable an ideal cross-linking and a robust templating synthesis of ordered MCs. This work presents a systematic study, by comparing three typical cross-linkers (formaldehyde, glyoxal, and glyoxylic acid), on the pore architecture, surface functionality, and electrochemical performance of resulting MCs. Both the type of cross-linker and its ratio with precursor monomer were found to be crucial for the pore architecture and electrochemical performance of resulting MCs. Glyoxal showed to be a promising cross-linker for easily generating ordered mesopores between 3.3-6.1 nm when the molar ratio between cross-linker and carbon precursor ranged from 1 to 2, whereas glyoxylic acid and formaldehyde induced interrupted or disordered mesopores. When the resulting MCs were used as supercapacitor electrodes, those cross-linked with glyoxal also led to overall higher capacitance in both 6 M KOH aqueous and ionic liquid [N2220][NTf2]/acetonitrile electrolytes thanks to the dominance of ordered mesopore channels, especially MC prepared at glyoxal/precursor molar ratio of 1.5. These findings on the effect of cross-linking on templating synthesis can be used to guide the customisation of MCs for supercapacitors and other applications by smartly choosing a suitable cross-linking agent and its ratio with the precursor.

Synthesis and Characterization of MC/TiO2 NPs Nanocomposite for Removal of Pb2+ and Reuse of Spent Adsorbent for Blood Fingerprint Detection

The removal of toxic heavy metals from wastewater through the use of novel adsorbents is expensive. The challenge arises after the heavy metal is removed by the adsorbent, and the fate of the adsorbent is not taken care of. This may create secondary pollution. The study aimed to prepare mesoporous carbon (MC) from macadamia nutshells coated with titanium dioxide nanoparticles (TiO2 NPs) using a hydrothermal method to remove Pb2+ and to test the effectiveness of reusing the lead-loaded spent adsorbent (Pb2+-MC/TiO2 NP nanocomposite) in blood fingerprint detection. The samples were characterized using SEM, which confirmed spherical and flower-like structures of the nanomaterials, whereas TEM confirmed a particle size of 5 nm. The presence of functional groups such as C and Ti and a crystalline size of 4 nm were confirmed by FTIR and XRD, respectively. The surface area of 1283.822 m2/g for the MC/TiO2 NP nanocomposite was examined by BET. The removal of Pb2+ at pH 4 and the dosage of 1.6 g/L with the highest percentage removal of 98% were analyzed by ICP-OES. The Langmuir isotherm model best fit the experimental data, and the maximum adsorption capacity of the MC/TiO2 NP nanocomposite was 168.919 mg/g. The adsorption followed the pseudo-second-order kinetic model. The ΔH° (-54.783) represented the exothermic nature, and ΔG° (-0.133 to -4.743) indicated that the adsorption process is spontaneous. In the blood fingerprint detection, the fingerprint details were more visible after applying the Pb2+-MC/TiO2 NP nanocomposite than before the application. The reuse application experiments showed that the Pb2+-MC/TiO2 NP nanocomposite might be a useful alternative material for blood fingerprint enhancement when applied on nonporous surfaces, eliminating secondary pollution.

Synthesis of sulfonated lignin-derived ordered mesoporous carbon for catalytic production of furfural from xylose

Sulfonated lignin-derived ordered mesoporous carbon (OMC-SO₃H) solid acid was synthesized through solvent evaporation induced self-assembly (EISA) method followed by sulfonation, using lignin as carbon precursor and glyoxal as cross-linking agent during the preparation process. The as-synthesized OMC-SO₃H exhibited a typical 2D hexagonal meso-structure (space group p6mm) and showed a good catalytic performance for the catalytic conversion of hemicellulose-derived xylose to furfural. A highest furfural yield of 76.7% with 100% xylose conversion was achieved at 200 °C for 45 min in γ-valerolactone (GVL)-water (85:15 v/v%) mixture. The lignin-derived OMC-SO₃H solid acid catalyst showed superior stability and reusability, and was also applicable to the catalytic production of furfural from xylan. This work provides a promising strategy for the synthesis of ordered mesoporous carbon solid acid from green and sustainable lignin biomass resource, which has wide range of applications in the utilization of cellulose and hemicellulose.

An Efficient Catalyst Derived from Carboxylated Lignin-Anchored Iron Nanoparticle Compounds for Carbon Monoxide Hydrogenation Application

Catalytic activity and target product selectivity are strongly correlated to the size, crystallographic phase, and morphology of nanoparticles. In this study, waste lignin from paper pulp industry is employed as the carbon source, which is modified with carboxyl groups at the molecular level to facilitate anchoring of metals, and a new type of carbon-based catalyst was obtained after carbonization. As a result, the size of the metal particles is effectively controlled by the chelation between -COO- and Fe3+. Furthermore, Fe/CM-CL with a particle size of 1.5-2.5 nm shows excellent catalytic performance, the conversion of carbon monoxide reaches 82.3%, and the selectivity of methane reaches 73.2%.

Development of Lignin-Based Mesoporous Carbons for the Adsorption of Humic Acid

There is an increasing urge to make the transition toward biobased materials. Lignin, originating from lignocellulosic biomass, can be potentially valorized as humic acid (HA) adsorbents via lignin-based mesoporous carbon (MC). In this work, these materials were synthesized for the first time starting from modified lignin as the carbon precursor, using the soft-template methodology. The use of a novel synthetic approach, Claisen rearrangement of propargylated lignin, and a variety of surfactant templates (Pluronic, Kraton, and Solsperse) have been demonstrated to tune the properties of the resulting MCs. The obtained materials showed tunable properties (BET surface area: 95-367 m²/g, pore size: 3.3-36.6 nm, V _BJH pore volume: 0.05-0.33 m³/g, and carbon and oxygen content: 55.5-91.1 and 3.0-12.2%, respectively) and good performance in terms of one of the highest HA adsorption capacities reported for carbon adsorbents (up to 175 mg/g).

Controllable synthesis of spherical carbon particles transition from dense to hollow structure derived from Kraft lignin

The tailored synthesis of carbon particles with controllable shapes and structures from biomass as a raw material would be highly beneficial to meet the demands of various applications of carbon materials from the viewpoint of sustainable development goals. In this work, the spherical carbon particles were successfully synthesized through a spray drying method followed by the carbonization process, using Kraft lignin as the carbon source and potassium hydroxide (KOH) as the activation agent. As the results, the proposed method successfully controlled the shape and structure of the carbon particles from dense to hollow by adjusting the KOH concentration. Especially, this study represents the first demonstration that KOH plays a crucial role in the formation of particles with good sphericity and dense structures. In addition, to obtain an in-depth understanding of the particle formation of carbon particles, a possible mechanism is also investigated in this article. The resulting spherical carbon particles exhibited dense structures with a specific surface area (1233 m²g^-1) and tap density (1.46 g cm^-3) superior to those of irregular shape carbon particles.

Rational production of highly acidic sulfonated carbons from kraft lignins employing a fractionation process combined with acid-assisted hydrothermal carbonization

Highly acidic lignin-derived sulfonated carbons (LDSCs) were produced from hardwood and softwood kraft lignins under mild conditions by applying fractionation and/or pre-carbonization treatments combined with acid-assisted hydrothermal carbonization. The use of lignin fraction with higher amount oxygen, obtained from the fractionation process, resulted in carbon with the highest density of surface acid groups and improved catalytic activity. The LDSCs were successful tested in the dehydration reaction of fructose to obtain 5-hydroxymethylfurfural, and the best catalyst can be recycled without loss in its catalytic activity after perform a simple regeneration process. In contrast, the pre-carbonization step, commonly performed in several works, resulted in LDSCs with low acidity. A simple and optimized methodology for obtaining LDSCs under mild conditions was developed, and the correlations between the preparation method and the physicochemical and catalytic properties established in this work may be extendible to other starting materials for rational sulfonated carbons production.

Sustainable lignin-derived hierarchically porous carbon for capacitive deionization applications

Cross-linked lignin with glyoxal leads to a support mesopore structure of lignin-based porous carbon with improved capacitive deionization performance.

Major advances in the development of ordered mesoporous materials

This feature article presents the main developments in the area of ordered mesoporous materials (OMMs) since their discovery in 1992, which is considered one of the milestones in the history of porous materials.