Ultrasonic Synthesis of Carbon Nanotube-Titanium Dioxide Composites: Process Optimization via Response Surface Methodology

Investigating the carcinogenic and non-carcinogenic health hazards of heavy metal ions in Spinacia oleracea grown in agricultural soil treated with biochar and humic acid

This study addressed the bioaccumulation and human health risk among the consumption of Spinacia oleracea grown in agricultural soil treated with humic acid (189-2310 ppm) and biochars (0.00-5.10%.wt). The biochars came from two local feedstocks of rice-husk (RH) and sugar-beet-pulp (SBP) pyrolyzed at temperatures 300 and 600 °C. Total concentrations of Cu, Cd, and Ni found in both the soil and biomass/biochar exceeded global safety thresholds. The bioaccumulation levels of HMs in spinach leaves varied, with Fe reaching the highest concentration at 765.27 mg kg-1 and Cd having the lowest concentration at 3.31 mg kg-1. Overall, the concentrations of Zn, Cd, Pb, and Ni in spinach leaves exceeded the safety threshold limits, so that its consumption is not recommended. The assessment of hazard quotient (HI) for the HMs indicated potential health hazards for humans (HI > 1) from consuming the edible parts of spinach. The biochar application rates of 4.35%wt and 0.00%.wt resulted in the highest (3.69) and lowest (3.15) HI values, respectively. The cumulative carcinogenic risk (TCR) ranged from 0.0085 to 0.0119, exceeding the cancer risk threshold. Introducing 5.10%wt biomass/biochar resulted in a 36% rise in TCR compared to the control. The utilization of humic acid alongside HMs-polluted biochars results in elevated levels of HMs bioaccumulation exceeding the allowable thresholds in crops (with a maximum increase of 49% at 2000 ppm humic acid in comparison to 189 ppm). Consequently, this raised the HI by 46% and the TCR by 22%. This study demonstrated that the utilization of HMs-polluted biochars could potentially pose supplementary health hazards. Moreover, it is evident that the utilization of HMs-polluted biochars in treating metal-contaminated soil does not effectively stabilize or reduce pollution.

Optimization of tetracycline removal from water by iron-coated pine-bark biochar

We synthesized iron-coated pine-bark biochar (Fe-PBB) and determined the optimal conditions for removing the antibiotic tetracycline from water. The Fe-PBB was synthesized by depositing iron oxide on pyrolyzed pine-bark waste via a facile co-precipitation method. Characterization (SEM, EDX, and TGA) showed successful deposition of a mass of approximately 27% (w/w) iron on the PBB to synthesize Fe-PBB. Fe-PBB exhibited five times higher adsorption capacity (~ 10 mg/g) for tetracycline compared with PBB. The effects of initial tetracycline concentration, pH, temperature, and Fe-PBB dose on the adsorption removal of tetracycline from water were systematically investigated and optimized using a statistical experimental design and response surface methodology. The empirical relationship between the experimental factors and tetracycline removal was modeled, statistically validated through the analysis of variance, and used to predict the optimal conditions for adsorption removal of tetracycline. We found that ≥ 95% of the tetracycline can be removed at a tetracycline concentration of 1 mg/L, pH of 7, temperature of 50 °C, and a Fe-PBB dose of 2 g/L. The adsorption isotherm modeling study suggests that the adsorption of tetracycline can be attributed to the pore filling phenomenon and multilayer adsorption on the Fe-PBB. A thermodynamics study showed that the adsorption occurs spontaneously with an endothermic reaction.

Optimized removal of hexavalent chromium from water using spent tea leaves treated with ascorbic acid

Spent tea leaves were functionalized with ascorbic acid to obtain treated tea waste (t-TW) to encourage the adsorption of hexavalent chromium from water. The adsorption removal of Cr(VI) was systematically investigated as a function of four experimental factors: pH (2–12), initial Cr(VI) concentration (1–100 mg L⁻¹), t-TW dosage (0–4 g L⁻¹), and temperature (10–50 °C) by following a statistical experimental design. A central composite rotatable experimental design based on a response surface methodology was used to establish an empirical model that assessed the individual and combined effects of factors on adsorptive removal of Cr(VI). The model was experimentally verified and statistically validated then used to predict optimal adsorption removal of Cr(VI) from water. At optimized conditions, ≥ 99% of 1 mg L⁻¹ Cr(VI) can be removed by 4 g L⁻¹ t-TW at a pH of 9. The adsorptive mechanism was assessed by conducting kinetics and equilibrium studies. The adsorption of Cr(VI) by t-TW followed a pseudo-second-order kinetics model (k₂ = 0.001 g mg⁻¹ h⁻¹) and could be described by Langmuir and Temkin isotherms, indicating monolayer adsorption and predominantly adsorbate-adsorbent interactions. The t-TW exhibited a competitive Cr(VI) adsorption capacity of 232.2 mg g⁻¹ compared with the other low-cost adsorbents. These results support the utilization of tea waste for the removal of hazardous metal contaminants from aqueous systems.

Ionic Liquid and Tween-80 Mixture as an Effective Dispersant for Oil Spills: Toxicity, Biodegradability, and Optimization

Chemical dispersants are used extensively for oil spill remediation. Most of these dispersants are composed of a mixture of surfactants and organic solvents, which raises concerns about aquatic toxicity and environmental impact. In this study, the toxicity and biodegradability of an oil spill dispersant composed of the surface-active ionic liquid 1-butyl-3-methylimidazolium lauroyl sarcosinate [Bmim][Lausar] and Tween-80 were investigated. In addition, important environmental factors including salinity, temperature, and wave-mixing energy were optimized to obtain maximum dispersion effectiveness. The acute toxicity against zebrafish (Danio rerio) showed that the developed dispersant was practically non-toxic with a median lethal dose of more than 100 mg L^-1 after 96 h. The dispersant also demonstrated outstanding biodegradability of 66% after 28 days. A model was developed using a response surface methodology that efficiently (R ² = 0.992) related the salinity, temperature, and wave-mixing energy of seawater to dispersion effectiveness. The system was then optimized, and a high dispersion effectiveness of 89.70% was obtained with an experimental error of less than 2%. Our findings suggest that the surface-active ionic liquid and Tween-80 mixture could be a viable alternative to toxic chemical dispersants for oil spill remediation.

Rhodamine B Photodegradation in Aqueous Solutions Containing Nitrogen Doped TiO2 and Carbon Nanotubes Composites

In this work, new results concerning the potential of mixtures based on nitrogen doped titanium dioxide (TiO₂:N) and carbon nanotubes (CNTs) as possible catalyst candidates for the rhodamine B (RhB) UV photodegradation are reported. The RhB photodegradation was evaluated by UV-VIS absorption spectroscopy using samples of TiO₂:N and CNTs of the type of single-walled carbon nanotubes (SWNTs), double-wall carbon nanotubes (DWNTs), multi-wall carbon nanotubes (MWNTs), and single-walled carbon nanotubes functionalized with carboxyl groups (SWNT-COOH) having various concentrations of CNTs. The best photocatalytic performance was obtained for sample containing TiO₂:N and 2.5 wt.% SWNTs-COOH, when approx. 85% of dye removal was achieved after 300 min. of UV irradiation. The reaction kinetics of RhB aqueous solutions containing TiO₂:N/CNT mixtures followed a complex first-order kinetic model. The TiO₂:N/CNTs catalyst induced higher photodegradation efficiency of RhB than TiO₂:N due to the presence of CNTs, which act as adsorbent and dispersing agent and capture the photogenerated electrons of TiO₂:N hindering the electron-hole recombination.

Experimental modeling and optimization for the reduction of hexavalent chromium in aqueous solutions using ascorbic acid

In this study, we investigated the reduction of toxic Cr(VI) to less toxic Cr(III) using ascorbic acid in various aqueous solutions: deionized water, synthetic soft water, synthetic hard water, and real tap water. The experiments were performed using a statistical experimental design. Response surface methodology (RSM) was used to correlate Cr(VI) reduction (response variable) with experimental parameters such as initial Cr(VI) concentration, humic acid concentration, and ascorbic acid dosage. The empirical model obtained from the experiments was used to estimate and optimize the quantity of ascorbic acid required for the reduction of ≥ 99% Cr(VI) in water. The optimized dosages of ascorbic acid were predicted and experimentally validated for > 99.5% reduction of Cr(VI) (1, 10, 20, and 100 mg/L) in the solutions. Even a solution containing an initial Cr(VI) concentration of 100 mg/L was reduced in concentration ≥ 99.9% with optimal dosage of ascorbic acid (500 mg/L) in the presence of 20 mg/L humic acid. Moreover, the reaction kinetics (kobs-Cr(VI) = 0.71 mM-1 s-1) were sufficient to reduce the ≥ 99.9% Cr(VI) in 20 min. This study sheds new light on the effect of ascorbic acid on Cr(VI) reduction, and provides knowledge fundamental to optimize treatment of Cr(VI) contaminated water to environmentally acceptable endpoints.