Ammonium Nitrate-Assisted Synthesis of Nitrogen/Sulfur-Codoped Hierarchically Porous Carbons Derived from Ginkgo Leaf for Supercapacitors

The Impact of N/O-Functional Groups on the Sorption Capabilities of Activated Carbons Derived from Furfuryl Alcohol

This work describes the effect of nitrogen and oxygen functional groups on the sorption properties of activated carbons produced from furfuryl alcohol. The poly(furfuryl) alcohol underwent carbonization in nitrogen, ammonia, and ammonia and air (in a 3:2 proportion) atmospheres at 600 °C for 4 h. The resulting materials were subsequently activated in a carbon dioxide atmosphere for 1 h at temperatures of 700 °C, 800 °C, 900 °C, and 1000 °C. The X-ray photoelectron spectroscopy (XPS) findings suggest that ammoxidation is superior to amination in terms of nitrogen doping. The maximum nitrogen concentration achieved after ammoxidation was 25 at.%, which decreased to 4 at.% after activation. Additionally, it was observed that oxygen functional groups have a greater impact on porous structure development compared to nitrogen functional groups. The materials activated through carbonization under an ammonia/air atmosphere attained the highest oxygen concentration of roughly 19 at.% as confirmed by XPS. The materials were evaluated for their sorption capacities for carbon dioxide and ethylene, which were 2.2 mmol/g and 2.9 mmol/g, respectively, at 30 °C.

Inorganic Skeleton Reinforcement-A Generic Approach to Improve the Mechanical Properties of Biochar

Biochar is considered as a promising candidate for emerging sustainable energy systems and environmental technology applications. However, the improvement of mechanical properties remains challenges. Herein, we propose a generic strategy to enhance the mechanical properties of bio-based carbon materials through inorganic skeleton reinforcement. As a proof-of-concept, silane, geopolymer, and inorganic gel are selected as precursors. The composites' structures are characterized and an inorganic skeleton reinforcement mechanism is elucidated. Specifically, two types of reinforcement of the silicon-oxygen skeleton network formed in situ with biomass pyrolysis and the silica-oxy-al-oxy network are constructed to improve the mechanical properties. A significant improvement in mechanical strength was achieved for bio-based carbon materials. The compressive strength of well-balanced porous carbon materials modified by silane can reach up to 88.9 kPa, geopolymer-modified carbon material exhibits an enhanced compressive strength of 36.8 kPa, and that of inorganic-gel-polymer-modified carbon material is 124.6 kPa. Moreover, the prepared carbon materials with enhanced mechanical properties show excellent adsorption performance and high reusability for organic pollutant model compound methylene blue dye. This work demonstrates a promising and universal strategy for enhancing the mechanical properties of biomass-derived porous carbon materials.

A non-heat-source process for preparing graphene oxide with low energy consumption

As the most widely used method for preparing graphene oxide (GO), Hummers' method always involves a key step, that is adding water to concentrated sulfuric acid. We found that if this process is cancelled, the oxidation degree of GO will be significantly reduced. This means that the heat released during concentrated sulfuric acid dilution will promote further oxidation of GO. In this paper, we fully utilize the heat released during concentrated sulfuric acid dilution to develop a new non-heat-source process without any low-/high-temperature auxiliar, exponentially reducing the energy consumption and largely avoiding the frequent temperature control. The result shows that GO prepared by Hummers' method and that prepared by the proposed process show a similar structure, composition, morphology, and defect degree. Meanwhile, the corresponding reduced GO (rGO) obtained after reduction shows similar capacitive behavior. Their specific capacitances are 243.6 F g^-1 and 240.3 F g^-1 at 1 A g^-1, respectively, and they both have a long-term cycling performance (with a 100% capacitance retention after 10 000 cycles at 30 A g^-1). This study provides a new strategy for the preparation of GO with low energy consumption.

The Influence of NH4NO3 and NH4ClO4 on Porous Structure Development of Activated Carbons Produced from Furfuryl Alcohol

The influence of NH₄NO₃ and NH₄ClO₄ on the porous texture and structure development of activated carbons produced from a non-porous polymeric precursor synthesized from furfuryl alcohol has been studied. The non-doped counterparts were prepared and studied for comparison purposes. NH₄NO₃ and NH₄ClO₄-doped polymers were carbonized under N₂ atmosphere at 600 °C, followed by CO₂ activation at 1000 °C and the obtained carbon materials and activated carbons were thoroughly characterized. The porosity characterization data have shown that NH₄NO₃-derived ACs present the highest specific surface area (up to 1523 m²/g in the experimental conditions studied), and the resulting porosity distributions are strongly dependent on the activation conditions. Thus, 1 h activation is optimum for the microporosity development, whereas larger activation times lead to micropores enlargement and conversion into mesopores. The type of doping salts used also has a substantial impact on the surface chemical composition, i.e., C=O groups. Moreover, NH₄NO₃ and NH₄ClO₄ constitute good sources of nitrogen. The type and contribution of nitrogen species are dependent on the preparation conditions. Quaternary nitrogen only appears in doped samples prepared by carbonization and pyrrolic, pyrydinic, and nitrogen oxide groups appear in the NH₄NO₃ -series. NH₄NO₃ incorporation has led to optimized materials towards CO₂ and C₂H₄ sorption with just 1 h activation time.

Synthesis of lignin-derived nitrogen-doped carbon as a novel catalyst for 4-NP reduction evaluation

In this study, nitrogen-doped carbon (NC) was fabricated using lignin as carbon source and g-C₃N₄ as sacrificial template and nitrogen source. The structural properties of as-prepared NC were characterized by TEM, XRD, FT-IR, Raman, XPS and BET techniques. Attractively, NC has proved efficient for reducing 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) using NaBH₄ as hydrogen donor with high apparent rate constant (k_app = 4.77 min^-1) and specific mass activity (s = 361 mol kgcat^-1 h^-1), which values are superior to the previously reported catalysts in the literature. Density functional theory (DFT) calculations demonstrate that four kinds of N dopants can change the electronic structure of the adjacent carbon atoms and contribute to their catalytic properties dependant on N species, however, graphitic N species has much greater contribution to 4-NP adsorption and catalytic reduction. Furthermore, The preliminary mechanism of this transfer hydrogenation reaction over as-prepared NC is proposed on the basis of XPS and DFT data. Astoundingly, NC has excellent stability and reusability of six consecutive runs without loss of catalytic activity. These findings open up a vista to engineer lignin-derived NC as metal-free catalyst for hydrogenation reaction.