Discrimination of Bulk and Surface Refractive Index Change in Plasmonic Sensors with Narrow Bandwidth Resonance Combs

Double-layer optical fiber interferometer with bio-layer-modified reflector for label-free biosensing of inflammatory proteins

This work discusses label-free biosensing application of a double-layer optical fiber interferometer where the second layer tailors the reflection conditions at the external plain and supports changes in reflected optical spectrum when a bio-layer binds to it. The double-layer nanostructure consists of precisely tailored thin films, i.e., titanium (TiO2) and hafnium oxides (HfO2) deposited on single-mode fiber end-face by magnetron sputtering. It has been shown numerically and experimentally that the approach besides well spectrally defined interference pattern distinguishes refractive index (RI) changes taking place in a volume and on the sensor surface. These are of interest when label-free biosensing applications are considered. The case of myeloperoxidase (MPO) detection-a protein, which concentration rises during inflammation-is reported as an example of application. The response of the sensor to MPO in a concentration range of 1 × 10-11-5 × 10-6 g/mL was tested. An increase in the MPO concentration was followed by a redshift of the interference pattern and a decrease in reflected power. The negative control performed using ferritin proved specificity of the sensor. The results reported in this work indicate capability of the approach for diagnostic label-free biosensing, possibly also at in vivo conditions.

Hydrogel binding sodium alginate based optical fiber surface plasmon resonance for calcium ion trace detection

A plasmonic tilted fiber Bragg grating (TFBG)-based sensor for the detection of calcium ion (Ca2+) was proposed and demonstrated experimentally. Hydrogel material was synthesized by utilizing hydrogen bond recombination between cellulose nanocrystals (CNC) and polyvinyl alcohol (PVA). Sodium alginate (SA) was incorporated into this hydrogel material, resulting in a composite membrane with specific binding properties for Ca2+. The membrane was applied as a coating on the surface of a gold-coated TFBG. The CNC/PVA-SA modified gold on the TFBG surface enhanced the localized refractive index changes caused by variations of Ca2+ concentrations. The experimental results demonstrated an impressive limit of detection (LOD) of approximately 0.025 fM, which is five orders of magnitude better than the current LODs of similar Ca2+ sensors. And the proposed Ca2+ sensor exhibited a wide dynamic range of 10-16 M to 10-6 M.

Dual-Mode Comb Plasmonic Optical Fiber Sensing

Surface plasmon (SP) excitation in metal-coated tilted fiber Bragg gratings (TFBGs) has been a focal point for highly sensitive surface biosensing. Previous efforts focused on uniform metal layer deposition around the TFBG cross section and temperature self-compensation with the Bragg mode, requiring both careful control of the core-guided light polarization and interrogation over most of the C + L bands. To circumvent these two important practical limitations, we studied and developed an original platform based on partially coated TFBGs. The partial metal layer enables the generation of dual-comb resonances, encompassing highly sensitive (TM/EH mode families) and highly insensitive (TE/HE mode families) components in unpolarized transmission spectra. The interleaved comb of insensitive modes acts as wavelength and power references within the same spectral region as the SP-active modes. Despite reduced fabrication and measurement complexity, refractometric accuracy is not compromised through statistical averaging over seven individual resonances within a narrowband window of 10 nm. Consequently, measuring spectra over 60 nm is no longer needed to compensate for small temperature or power fluctuations. This sensing platform brings the following important practical assets: (1) a simpler fabrication process, (2) no need for polarization control, (3) limited bandwidth interrogation, and (4) maintained refractometric accuracy, which makes it a true game changer in the ever-growing plasmonic sensing domain.

Insulin biotrapping using plasmofluidic optical fiber chips: A benchmark

Plasmonic optical fiber-based biosensors are currently in their early stages of development as practical and integrated devices, gradually making their way towards the market. While the majority of these biosensors operate using white light and multimode optical fibers (OFs), our approach centers on single-mode OFs coupled with tilted fiber Bragg gratings (TFBGs) in the near-infrared wavelength range. Our objective is to enhance surface sensitivity and broaden sensing capabilities of OF-based sensors to develop in situ sensing with remote interrogation. In this study, we comprehensively assess their performance in comparison to the gold-standard plasmonic reference, a commercial device based on the Kretschmann-Raether prism configuration. We present their refractive index sensitivity and their capability for insulin sensing using a dedicated microfluidics approach. By optimizing a consistent surface biotrapping methodology, we elucidate the dynamic facets of both technologies and highlight their remarkable sensitivity to variations in bulk and surface properties. The one-to-one comparison between both technologies demonstrates the reliability of optical fiber-based measurements, showcasing similar experimental trends obtained with both the prismatic configuration and gold-coated TFBGs, with an even enhanced limit of detection for the latter. This study lays the foundation for the detection of punctual molecular interactions and opens the way towards the detection of spatially and temporally localized events on the surface of optical probes.

Ultrasensitive and Multiple Biomarker Discrimination for Alzheimer's Disease via Plasmonic & Microfluidic Sensing Technologies

As the population ages, the worldwide prevalence of Alzheimer's disease (AD) as the most common dementia in the elderly is increasing dramatically. However, a long-term challenge is to achieve rapid and accurate early diagnosis of AD by detecting hallmarks such as amyloid beta (Aβ42). Here, a multi-channel microfluidic-based plasmonic fiber-optic biosensing platform is established for simultaneous detection and differentiation of multiple AD biomarkers. The platform is based on a gold-coated, highly-tilted fiber Bragg grating (TFBG) and a custom-developed microfluidics. TFBG excites a high-density, narrow-cladding-mode spectral comb that overlaps with the broad absorption of surface plasmons for high-precision interrogation, enabling ultrasensitive monitoring of analytes. In situ detection and in-parallel discrimination of different forms of Aβ42 in cerebrospinal fluid (CSF) are successfully demonstrated with a detection of limit in the range of ≈30-170 pg mL-1, which is one order of magnitude below the clinical cut-off level in AD onset, providing high detection sensitivity for early diagnosis of AD. The integration of the TFBG sensor with multi-channel microfluidics enables simultaneous detection of multiple biomarkers using sub-µL sample volumes, as well as combining initial binding rate and real-time response time to differentiate between multiple biomarkers in terms of binding kinetics. With the advantages of multi-parameter, low consumption, and highly sensitive detection, the sensor represents an urgently needed potentials for large-scale diagnosis of diseases at early stage.

Application of fiber loop ringdown spectroscopy technique for a new approach to beta-amyloid monitoring for Alzheimer Disease's early detection

A novel fiber optic biosensor was purposed for a new approach to monitor amyloid beta protein fragment 1-42 (Aβ42) for Alzheimer's Disease (AD) early detection. The sensor was fabricated by etching a part of fiber from single mode fiber loop in pure hydrofluoric acid solution and utilized as a Local Optical Refractometer (LOR) to monitor the change Aβ42 concentration in Artificial Cerebrospinal Fluid (ACSF). The Fiber Loop Ringdown Spectroscopy (FLRDS) technique is an ultra-sensitive measurement technique with low-cost, high sensitivity, real-time measurement, continuous measurement and portability features that was utilized with a fiber optic sensor for the first time for the detection of a biological signature in an ACSF environment. Here, the measurement is based on the total optical loss detection when specially fabricated sensor heads were immersed into ACSF solutions with and without different concentrations of Aβ42 biomarkers since the bulk refractive index change was performed. Baseline stability and the reference ring down times of the sensor head were measured in the air as 0.87% and 441.6μs ± 3.9μs, respectively. Afterward, the total optical loss of the system was measured when the sensor head was immersed in deionized water, ACSF solution, and ACSF solutions with Aβ42 in different concentrations. The lowest Aβ42 concentration of 2 ppm was detected by LOR. Results showed that LOR fabricated by single-mode fibers for FLRDS system design are promising candidates to be utilized as fiber optic biosensors after sensor head modification and have a high potential for early detection applications of not only AD but possibly also several fatal diseases such as diabetes and cancer.

Operando monitoring of dendrite formation in lithium metal batteries via ultrasensitive tilted fiber Bragg grating sensors

Lithium (Li) dendrite growth significantly deteriorates the performance and shortens the operation life of lithium metal batteries. Capturing the intricate dynamics of surface localized and rapid mass transport at the electrolyte-electrode interface of lithium metal is essential for the understanding of the dendrite growth process, and the evaluation of the solutions mitigating the dendrite growth issue. Here we demonstrate an approach based on an ultrasensitive tilted fiber Bragg grating (TFBG) sensor which is inserted close to the electrode surface in a working lithium metal battery, without disturbing its operation. Thanks to the superfine optical resonances of the TFBG, in situ and rapid monitoring of mass transport kinetics and lithium dendrite growth at the nanoscale interface of lithium anodes have been achieved. Reliable correlations between the performance of different natural/artificial solid electrolyte interphases (SEIs) and the time-resolved optical responses have been observed and quantified, enabling us to link the nanoscale ion and SEI behavior with the macroscopic battery performance. This new operando tool will provide additional capabilities for parametrization of the batteries' electrochemistry and help identify the optimal interphases of lithium metal batteries to enhance battery performance and its safety.

Rapid ultra-sensitive nucleic acid detection using plasmonic fiber-optic spectral combs and gold nanoparticle-tagged targets

Nucleic acid (NA) is a widely-used biomarker for viruses. Accurate quantification of NA can provide a reliable basis for point-of-care diagnosis and treatment. Here, we propose a tilted fiber Bragg grating (TFBG)-based plasmonic fiber-optic spectral comb for fast response and ultralow limit NA detection. The TFBG is coated with a gold film which enables excitation of surface plasmon resonance (SPR), and single-stranded probe NAs with known base sequences are assembled on the gold film. To enhance sensitivity of refractive index (RI) for sensing a chosen combination of probe and target NAs around the TFBG surface, gold nanoparticles (AuNPs) are bonded to the target NA molecules as "RI-labels". The NA combination-induced aggregation of AuNPs induces significant spectral responses in the TFBG that would be below the detection threshold for the NAs in the absence of the AuNPs. The proposed TFBG-SPR NA sensor shows a fast response time of 30 s and an ultra-wide NA detection range from 1 × 10-18 mol/L to 1 × 10-7 mol/L. In the NA concentration range of 1 × 10-12 mol/L (1 pM) to 105 pM, an ultra-high sensitivity of 1.534 dB/lg(pM) is obtained. The sensor achieves an ultra-low limit of detection down to 1.0 × 10-18 mol/L (1 aM), which is more than an order of magnitude lower than the previous reports. The proposed sensor not only shows potentials in practical applications of NA detection, but also provides a new way for TFBG-SPR biochemical sensors to achieve higher RI sensitivity.

Detangling electrolyte chemical dynamics in lithium sulfur batteries by operando monitoring with optical resonance combs

Challenges in enabling next-generation rechargeable batteries with lower cost, higher energy density, and longer cycling life stem not only from combining appropriate materials, but from optimally using cell components. One-size-fits-all approaches to operational cycling and monitoring are limited in improving sustainability if they cannot utilize and capture essential chemical dynamics and states of electrodes and electrolytes. Herein we describe and show how the use of tilted fiber Bragg grating (TFBG) sensors to track, via the monitoring of both temperature and refractive index metrics, electrolyte-electrode coupled changes that fundamentally control lithium sulfur batteries. Through quantitative sensing of the sulfur concentration in the electrolyte, we demonstrate that the nucleation pathway and crystallization of Li2S and sulfur govern the cycling performance. With this technique, a critical milestone is achieved, not only towards developing chemistry-wise cells (in terms of smart battery sensing leading to improved safety and health diagnostics), but further towards demonstrating that the coupling of sensing and cycling can revitalize known cell chemistries and break open new directions for their development.

Rapid detection of hydrogen using narrow bandwidth fiber-optic spectral combs with a low limit of detection

The all-fiber detection solutions are the key technology to detecting hydrogen leakage in time because of the low explosive limit of the hydrogen-air mixture gas. However, most of the fiber-optic-based hydrogen sensing platforms must disrupt their structure to achieve a special architecture for interacting with the hydrogen. Here, we report a promising non-damaged structure of fiber-optic narrow bandwidth spectral combs, that can be developed to determine the refractive change as low as 10-5 using its cut-off cladding resonance mode. Such high performance of response for the refractive index induces a rapid detection of hydrogen after a proper thickness of palladium was deposited on the device. An average response time of hydrogen of 4 min with a low limit of detection of 348 ppm was achieved. It is demonstrated that these narrow bandwidth fiber-optic resonance combs can be used for gas detection after being combined with functional materials.

Ultra-sensitive and specific detection of pathogenic nucleic acids using composite-excited hyperfine plasma spectroscopy combs sensitized by Au nanoarrays functionalized with 2D Ta2C-MXene

Accurate and rapid screening techniques on a population scale are crucial for preventing and managing epidemics like COVID-19. The standard gold test for nucleic acids in pathogenic infections is primarily the reverse transcription polymerase chain reaction (RT-PCR). However, this method is not suitable for widespread screening due to its reliance on large-scale equipment and time-consuming extraction and amplification processes. Here, we developed a collaborative system that combines high-load hybridization probes targeting N and OFR1a with Au NPs@Ta2C-M modified gold-coated tilted fiber Bragg grating (TFBG) sensors to enable direct nucleic acid detection. Multiple activation sites of SARS-CoV-2 were saturable modified on the surface of a homogeneous arrayed AuNPs@Ta2C-M/Au structure based on a segmental modification approach. The combination of hybrid probe synergy and composite polarisation response in the excitation structure results in highly specific hybridization analysis and excellent signal transduction of trace target sequences. The system demonstrates excellent trace specificity, with a limit of detection of 0.2 pg/mL, and achieves a rapid response time of 1.5 min for clinical samples without amplification. The results showed high agreement with the RT-PCR test (Kappa index = 1). And the gradient-based detection of 10-in-1 mixed samples exhibits high-intensity interference immunity and excellent trace identification. Therefore, the proposed synergistic detection platform has a good tendency to curb the global spread of epidemics such as COVID-19.

Decoupling bulk and surface characteristics with a bare tilted fiber Bragg grating

The tilted fiber Bragg grating (TFBG) with dense comb-like resonances offers a promising fiber-optic sensing platform but could suffer from cross sensitivity dependent on bulk and surface environment. In this work, the decoupling of bulk and surface characteristics (indicated by bulk refractive index (RI) and surface-localized binding film) from each other is attained theoretically with a bare TFBG sensor. This is realized with the proposed decoupling approach based on differential spectral responses of cut-off mode resonance and mode dispersion represented as wavelength interval between P- and S-polarized resonances of the TFBG to the bulk RI and surface film thickness. The results demonstrate that with this method the sensing performance for decoupling bulk RI and surface film thickness is comparative to the cases in which either the bulk or surface environment of the TFBG sensor changes, with the bulk and surface sensitivities over 540 nm/RIU and 12 pm/nm, respectively.

Accurate compensation and prediction of the temperature cross-sensitivity of tilted FBG cladding mode resonances

The temperature dependence of core mode resonance has been thoroughly studied in fiber Bragg gratings (FBGs), but it is not the case for cladding mode resonances in multi-resonance gratings such as tilted FBGs (TFBGs). In this work, the temperature sensitivity of ultraviolet written TFBGs in SMF-28 fibers is assessed, demonstrating in the first, to the best of our knowledge, place that a single gauge factor K T =6.25⋅10-6±0.02⋅10-6 ∘ C -1 can be employed to characterize the response to temperature of the resonances over the full spectrum in the 10°-50°C range. Then, a simulation model is obtained, enabling to predict TFBG spectra in the 10°-50°C range with high accuracy. This requires a calibration of the core index and dispersion of the TFBG measured in air at 25°C, and determination of the glass refractive index thermo-optic coefficient (d n/d T=8.46⋅10-6±0.1⋅10-6 ∘ C -1, common to both core and cladding glasses), leading to a mean error on the wavelength position of resonances between 1 and 3 pm. This mean error can be further reduced (less than 1 pm) by considering a linear dependence with temperature of d n/d T. Therefore, this model will enable to completely remove the temperature-induced shifts of all resonances in TFBG sensing applications and measure with great accuracy the variables of interest by using the scaled averages of groups of resonances instead of (less accurate) individual shifts.

High confidence plasmonic sensor based on photonic crystal fibers with a U-shaped detection channel

In order to improve the performance of optical fiber sensing and expand its application, a photonic crystal fiber (PCF) plasmonic sensor with a U-shaped channel based on surface plasmon resonance (SPR) is proposed. We have studied the general influence rules of structural parameters such as the radius of the air hole, the thickness of the gold film and the number of U-shaped channels using COMSOL based on the finite element method. The dispersion curves and loss spectrum of the surface plasmon polariton (SPP) mode and the Y-polarization (Y-pol) mode as well as the distribution of the electric field intensity (normE) under various conditions are studied using the coupled mode theory. The maximum refractive index (RI) sensitivity achieved in the RI range of 1.38-1.43 is 24.1 μm RIU^-1, which corresponds to a full width at half maximum (FWHM) of 10.0 nm, a figure of merit (FOM) of 2410 RIU^-1 and a resolution of 4.15 × 10^-6 RIU. The results show that the proposed sensor combines the SPR effect, which is extremely sensitive to changes in the RI of the surrounding medium and realizes real-time detection of the external environment by analyzing the light signal modulated by the sensor. In addition, the detection range and sensitivity can be extended by adjusting the structural parameters. The proposed sensor has a simple structure with excellent sensing performance, which provides a new idea and implementation method for real-time detection, long-range measurement, complex environment monitoring and highly integrated sensing, and has a strong potential practical value.

Long Period Grating Mach-Zehnder Interferometer Based Immunosensor with Temperature and Bulk Refractive Index Compensation

A long period grating Mach-Zehnder interferometer (LPGMZI) that consists of two identical long period gratings (LPGs) in a single fibre was developed to measure immunoglobulin M (IgM). The measured spectrum has fringes due to the interference between the core mode and cladding mode. This immunosensor inherits the advantages of an LPG and has the potential to compensate for unwanted signal changes due to bulk refractive index (RI) and temperature fluctuations by analysing interference fringes and their envelope. The external RI was measured from 1.3384 to 1.3670 in two different cases: (i) only the connecting section between the two LPGs is immersed or (ii) the whole LPGMZI is immersed. The fringes shift with an external RI in both scenarios, whereas the envelope stays still in case (i) or shifts at the same rate as the fringes in case (ii). The LPGMZI was also characterised at different temperatures between 25 °C and 30 °C by placing the whole LPGMZI in a water bath. The fringes and envelope shift at the same rate with temperature. The LPGMZI platform was then used to create an IgM immunosensor. The connecting section between the two LPGs was functionalised with anti-IgM and immersed into solutions with IgM concentrations from 20 μg/mL to 320 μg/mL. The fringes shift with IgM concentration and the envelope remains static. The results from this work show that LPGMZI has the potential to compensate for the temperature and bulk RI fluctuations and perform as a portable biosensor platform.

Design and Implementation of a Dual-Region Self-Referencing Fiber-Optic Surface Plasmon Resonance Biosensor

The need for self-referencing is extremely important in the field of biosensing. In this manuscript, we report on the study, design, and validation of a dual-region self-referencing fiber-optic surface plasmon resonance biosensor. One region is intended to measure and monitor the binding events of the biological sample under test, while the other one is designed to be used as a reference channel to compensate for external factors, such as bulk refractive index modifications and temperature oscillations, that can negatively affect the biomolecular interaction measurement. Two different configurations for the biosensor probe are presented and investigated here, both theoretically and experimentally. First, the theoretical performance of the proposed biosensor probes, in terms of surface plasmon resonance wavelength shift, was simulated using a numerical model. Afterward, they were experimentally validated in sucrose-water solutions and showed a response to refractive index and temperature changes with sensitivities up to 2000 nm/RIU and 1.559 nm/°C, respectively. Finally, an aptamer-based bioassay and a high-resolution melting assay were successfully implemented on the two proposed configurations, demonstrating the feasibility of analyzing the binding events and measuring other external signal modifications simultaneously using the same biosensor probe.

Novel Optical Fiber-Based Structures for Plasmonics Sensors

Optical fiber sensors based on surface plasma technology have many unique advantages in specific applications such as extreme environmental monitoring, physical parameter determination, and biomedical indicators testing. In recent decades, various kinds of fiber probes with special structures were developed according to special processing such as tapering, splicing, etching, fiber balls, grating etc. In this paper, the fabrication technology, characteristics, development status and application scenarios of different special optical fiber structures are briefly reviewed, including common processing equipment. Furthermore, many special novel optical fiber structures reported in recent years are summarized, which have been used in various kinds of plasmonic sensing work. Then, the fiber-plasmonic sensors for practical applications are also introduced and examined in detail. The main aim of this review is to provide guidance and inspiration for researchers to design and fabricate special optical fiber structures, thus facilitating their further research.

Partially gold-coated tilted FBGs for enhanced surface biosensing

To date, there is clear experimental evidence that gold-coated tilted fiber Bragg gratings (TFBGs) are highly sensitive plasmonic biosensors that provide temperature-compensated detection of analytes at concentrations in the picomolar range. As most optical biosensors, they bring an evanescent wave in the surrounding medium, which makes them sensitive to both surface refractive index variations (= the useful biosensing signal) and to bulk refractive index changes (= the non-useful signal for biosensing). This dual sensitivity makes them prone to drift. In this work, we study partially gold-coated TFBGs around their cross-section. These gratings present the ability to discriminate both volume and surface refractive index changes, which is interesting in biosensing to enhance the signal-to-noise ratio. The effects induced in the TFBGs transmitted amplitude spectra were analyzed for surrounding refractive index (SRI) changes in the range 1.3360-1.3370. Then, the gold film was biofunctionalized with human epidermal growth factor receptor (HER2) aptamers using thiol chemistry. The detection of HER2 proteins (a relevant cancer biomarker) at 10^-9 g/mL, 10^-8 g/mL and 10^-6 g/mL demonstrated the advantage to identify environmental perturbations through the bare area of the TFBGs, which is left not functionalized. The non-specific drifts that could exist in samples are eliminated and a wavelength shift only related to the surface modification is obtained.

Accurate Correction of the "Bulk Response" in Surface Plasmon Resonance Sensing Provides New Insights on Interactions Involving Lysozyme and Poly(ethylene glycol)

Surface plasmon resonance is a very well-established surface sensitive technique for label-free analysis of biomolecular interactions, generating thousands of publications each year. An inconvenient effect that complicates interpretation of SPR results is the “bulk response” from molecules in solution, which generate signals without really binding to the surface. Here we present a physical model for determining the bulk response contribution and verify its accuracy. Our method does not require a reference channel or a separate surface region. We show that proper subtraction of the bulk response reveals an interaction between poly(ethylene glycol) brushes and the protein lysozyme at physiological conditions. Importantly, we also show that the bulk response correction method implemented in commercial instruments is not generally accurate. Using our method, the equilibrium affinity between polymer and protein is determined to be K_D = 200 μM. One reason for the weak affinity is that the interaction is relatively short-lived (1/k_off < 30 s). Furthermore, we show that the bulk response correction also reveals the dynamics of self-interactions between lysozyme molecules on surfaces. Besides providing new insights on important biomolecular interactions, our method can be widely applied to improve the accuracy of SPR data generated by instruments worldwide.

Research on the High Temperature and High Pressure Gold-Plated Fiber Grating Dual-Parameter Sensing Measurement System

In electrohydrostatic drive actuators, there is a demand for temperature and pressure monitoring in complex environments. Fiber Bragg grating (FBG) has become a promising sensor for measuring temperature and pressure. However, there is a cross-sensitivity between temperature and pressure. A gold-plated FBG is proposed and manufactured, and an FBG is used as a reference grating to form a parallel all-fiber sensing system, which can realize the simultaneous measurement of pressure and temperature. Based on the simulation software, the mechanical distribution of the pressure diaphragm is analyzed, and the fixation scheme of the sensor is determined. Using the demodulator to monitor the changes in the reflectance spectrum in real-time, the pressure and ambient temperature applied to the sensor are measured. The experimental results show that the temperature sensitivity of gold-plated FBG is 3 times that of quartz FBG, which can effectively distinguish the temperature changes. The pressure response sensitivity of gold-plated FBG is 0.3 nm/MPa, which is same as the quartz FBG. Through the sensitivity matrix equation, the temperature and pressure dual-parameter sensing measurement is realized. The accuracy of the temperature and pressure measurement is 97.7% and 99.0%, and the corresponding response rates are 2.7 ms/°C and 2 ms/MPa, respectively. The sensor has a simple structure and high sensitivity, and it is promising to be applied in health monitoring in complex environments with a high temperature and high pressure.

Aptamer-Assisted Protein Orientation on Silver Magnetic Nanoparticles: Application to Sensitive Leukocyte Cell-Derived Chemotaxin 2 Surface Plasmon Resonance Sensors

Leukocyte cell-derived chemotaxin 2 (LECT2) has been proved to be a potential biomarker for the diagnosis of liver fibrosis. In this work, a sensitive surface plasmon resonance (SPR) assay for LECT2 analysis was developed. Tyrosine kinase with immune globulin-like and epidermal growth factor-like domains 1 (Tie1) is an orphan receptor of LECT2 with a C-terminal Fc tag, which is far away from the LECT2 binding sites. The Fc aptamer was intentionally used to capture the Tie1 through its Fc tag, connecting with Fe₃O₄-coated silver magnetic nanoparticles (Ag@MNPs) and ensuring the LECT2 binding site to be outward. Attributed to the orientation nature of the captured protein, Ag@MNPs were able to enhance the SPR signal. A sensitive LECT2 sensor was successfully fabricated with a detection limit of 10.93 pg/mL. The results showed that the immobilization method improved the binding efficiency of Tie1 protein. This strategy could be extended to attach antibodies or recombinant Fc label proteins to Fc aptamer-based nanoparticles.

Ultrasensitive detection of endocrine disruptors via superfine plasmonic spectral combs

The apparent increase in hormone-induced cancers and disorders of the reproductive tract has led to a growing demand for new technologies capable of detecting endocrine disruptors. However, a long-lasting challenge unaddressed is how to achieve ultrahigh sensitive, continuous, and in situ measurement with a portable device for in-field and remote environmental monitoring. Here we demonstrate a simple-to-implement plasmonic optical fiber biosensing platform to achieve an improved light-matter interaction and advanced surface chemistry for ultrasensitive detection of endocrine disruptors. Our platform is based on a gold-coated highly tilted fiber Bragg grating that excites high-density narrow cladding mode spectral combs that overlap with the broad absorption of the surface plasmon for high accuracy interrogation, hence enabling the ultrasensitive monitoring of refractive index changes at the fiber surface. Through the use of estrogen receptors as the model, we design an estradiol-streptavidin conjugate with the assistance of molecular dynamics, converting the specific recognition of environmental estrogens (EEs) by estrogen receptor into surface-based affinity bioassay for protein. The ultrasensitive platform with conjugate-induced amplification biosensing approach enables the subsequent detection for EEs down to 1.5 × 10^-3 ng ml^-1 estradiol equivalent concentration level, which is one order lower than the defined maximal E₂ level in drinking water set by the Japanese government. The capability to detect EEs down to nanogram per liter level is the lowest limit of detection for any estrogen receptor-based detection reported thus far. Its compact size, flexible shape, and remote operation capability open the way for detecting other endocrine disruptors with ultrahigh sensitivity and in various hard-to-reach spaces, thereby having the potential to revolutionize environment and health monitoring.

Surface Plasmonic Sensors: Sensing Mechanism and Recent Applications

Surface plasmonic sensors have been widely used in biology, chemistry, and environment monitoring. These sensors exhibit extraordinary sensitivity based on surface plasmon resonance (SPR) or localized surface plasmon resonance (LSPR) effects, and they have found commercial applications. In this review, we present recent progress in the field of surface plasmonic sensors, mainly in the configurations of planar metastructures and optical-fiber waveguides. In the metastructure platform, the optical sensors based on LSPR, hyperbolic dispersion, Fano resonance, and two-dimensional (2D) materials integration are introduced. The optical-fiber sensors integrated with LSPR/SPR structures and 2D materials are summarized. We also introduce the recent advances in quantum plasmonic sensing beyond the classical shot noise limit. The challenges and opportunities in this field are discussed.