Organization of Pseudomonas fluorescens on chemically different nano/microstructured surfaces

The Effects of Subcellular Nanograting Geometry on the Formation and Growth of Bacterial Biofilms

Biofilm formation by bacteria protects them against environmental stresses such as desiccation, shear forces and antimicrobial agents, making them much harder to remove and increasing their virulence and persistence in industrial water systems and biomedical equipment. One promising method of disrupting biofilm formation and growth is to employ passive surface structures to inhibit bacterial adhesion and aggregation. However, most studies thus far have mainly focused on the early stages of biofilm formation and it is unclear if the influence of surface topography in the early phase will propagate to later stages. Here, we attempt to address this with an investigation into the biofilm formation of Pseudomonas aeruginosa on 25 different nanograting geometries, with dimensions that were systematically varied from subcellular to cellular sizes. The biofilms were characterized from the exponential growth phase to the decline phase, in intervals of 24 H over 4 days, using confocal scanning laser microscopy. Comparing the maximum volume of biofilm formed on each surface over 96 H, it was found that approximately 1/3 of the nanograting geometries exhibited 72 ± 16 % lower biovolume density than a flat surface. Bacteria on these nanogratings were also observed to form 40 ± 11 % smaller microcolonies that were 17 ± 6 % less compact than that found on the control surface. The majority of these nanogratings had deep trenches (i.e. depth ≥ 70% of the cell diameter). Furthermore, P. aeruginosa cells were observed to multiply at approximately twice the rate on almost all the nanogratings compared to flat surfaces, but these cell populations also began to decline 24 H earlier than those on a flat surface. Using available literature on P. aeruginosa, a qualitative model was put forth, attributing the results to increased cell motility, decreased exopolysaccharide formation and disrupted psl adhesin/signal trails on nanogratings. These factors, together, led to the net effects of reduced attachment, increased scattering of cells and rapid decline of the biofilms on nanogratings. The insights derived from this study suggest that passive surface geometries can be designed and optimized to successfully control/inhibit biofilm formation and growth.

Impact of electrode micro- and nano-scale topography on the formation and performance of microbial electrodes

From a fundamental standpoint, microbial electrochemistry is unravelling a thrilling link between life and materials. Technically, it may be the source of a large number of new processes such as microbial fuel cells for powering remote sensors, autonomous sensors, microbial electrolysers and equipment for effluent treatment. Microbial electron transfers are also involved in many natural processes such as biocorrosion. In these contexts, a huge number of studies have dealt with the impact of electrode materials, coatings and surface functionalizations but very few have focused on the effect of the surface topography, although it has often been pointed out as a key parameter impacting the performance of electroactive biofilms. The first part of the review gives an overview of the influence of electrode topography on abiotic electrochemical reactions. The second part recalls some basics of the effect of surface topography on bacterial adhesion and biofilm formation, in a broad domain reaching beyond the context of electroactivity. On these well-established bases, the effect of surface topography is reviewed and analysed in the field of electroactive biofilms. General trends are extracted and fundamental questions are pointed out, which should be addressed to boost future research endeavours. The objective is to provide basic guidelines useful to the widest possible range of research communities so that they can exploit surface topography as a powerful lever to improve, or to mitigate in the case of biocorrosion for instance, the performance of electrode/biofilm interfaces.

Self-sterilizing ormosils surfaces based on photo-synzthesized silver nanoparticles

Medical device-related infections represent a major healthcare complication, resulting in potential risks for the patient. Antimicrobial materials comprise an attractive strategy against bacterial colonization and biofilm proliferation. However, in most cases these materials are only bacteriostatic or bactericidal, and consequently they must be used in combination with other antimicrobials in order to reach the eradication condition (no viable microorganisms). In this study, a straightforward and robust antibacterial coating based on Phosphotungstate Ormosil doped with core-shell (SiO₂@TiO₂) was developed using sol-gel process, chemical tempering, and Ag nanoparticle photoassisted synthesis (POrs-CS-Ag). The coating was characterized by X-ray Fluorescence Spectroscopy (XRF), Field Emission Scanning Electron Microscopy (FE-SEM), Atomic Force Microscopy (AFM) and X-ray Photoelectron Microscopy (XPS). The silver free coating displays low antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa, in opposition to the silver loaded ones, which are able to completely eradicate these strains. Moreover, the antimicrobial activity of these substrates remains high until three reutilization cycles, which make them a promising strategy to develop self-sterilizing materials, such as POrs-CS-Ag-impregnated fabric, POrs-CS-Ag coated indwelling metals and polymers, among other materials.

Polymer-Based Surfaces Designed to Reduce Biofilm Formation: From Antimicrobial Polymers to Strategies for Long-Term Applications

Contact-active antimicrobial polymer surfaces bear cationic charges and kill or deactivate bacteria by interaction with the negatively charged parts of their cell envelope (lipopolysaccharides, peptidoglycan, and membrane lipids). The exact mechanism of this interaction is still under debate. While cationic antimicrobial polymer surfaces can be very useful for short-term applications, they lose their activity once they are contaminated by a sufficiently thick layer of adhering biomolecules or bacterial cell debris. This layer shields incoming bacteria from the antimicrobially active cationic surface moieties. Besides discussing antimicrobial surfaces, this feature article focuses on recent strategies that were developed to overcome the contamination problem. This includes bifunctional materials with simultaneously presented antimicrobial and protein-repellent moieties; polymer surfaces that can be switched from an antimicrobial, cell-attractive to a cell-repellent state; polymer surfaces that can be regenerated by enzyme action; degradable antimicrobial polymers; and antimicrobial polymer surfaces with removable top layers.

Surface Structuring Meets Orthogonal Chemical Modifications: Toward a Technology Platform for Site-Selectively Functionalized Polymer Surfaces and BioMEMS

A manufacturing process for the site-selective modification of structured (bio)material surfaces with two different polymers/biomolecules is presented. In the first step, a chemical surface contrast is created (e.g., a gold-on-silicon contrast obtained by colloidal lithography), and is combined with two orthogonal surface reactions for polymer/biomolecule immobilization. To demonstrate this, an antimicrobial SMAMP polymer and a protein-repellent polyzwitterion were site-selectively surface-immobilized on the gold-silicon structures. By varying the structure spacing and the surface architecture, structure-property relationships for the interaction of these bifunctional polymer surfaces with bacteria and proteins were obtained (studied by fluorescence microscopy, atomic force microscopy, surface plasmon resonance spectroscopy, and antimicrobial assays). At 1 μm spacing, a fully antimicrobially active bifunctional material was obtained, which also near-quantitatively reduced protein adhesion. As the process is generally applicable to polymers/biomolecules with aliphatic CH-groups, it is an interesting platform technology for site-selectively functionalized bifunctional (Bio)MEMS.

Antibiofilm effect of supramolecularly templated mesoporous silica coatings

Bacteria attached to solid surfaces and encased in a self-synthesized matrix, so-called biofilms, are highly difficult to eradicate and present negative impact on industry and human health. The ability of supramolecularly templated mesoporous silica coatings to inhibit biofilm formation in Pseudomonas aeruginosa is shown here. Assays employing submerged and air-liquid interface biofilms demonstrated that mesoporous coatings with tuned pore size significantly reduce the number of attached bacteria and matrix production. Given its versatility, scalability, robustness and low cost, our proposal is attractive for the production of transparent, inert and permanent antibiofilm coatings that could be applied on multiple surfaces.

Atomic Step Formation on Sapphire Surface in Ultra-precision Manufacturing

Surfaces with controlled atomic step structures as substrates are highly relevant to desirable performances of materials grown on them, such as light emitting diode (LED) epitaxial layers, nanotubes and nanoribbons. However, very limited attention has been paid to the step formation in manufacturing process. In the present work, investigations have been conducted into this step formation mechanism on the sapphire c (0001) surface by using both experiments and simulations. The step evolutions at different stages in the polishing process were investigated with atomic force microscopy (AFM) and high resolution transmission electron microscopy (HRTEM). The simulation of idealized steps was constructed theoretically on the basis of experimental results. It was found that (1) the subtle atomic structures (e.g., steps with different sawteeth, as well as steps with straight and zigzag edges), (2) the periodicity and (3) the degree of order of the steps were all dependent on surface composition and miscut direction (step edge direction). A comparison between experimental results and idealized step models of different surface compositions has been made. It has been found that the structure on the polished surface was in accordance with some surface compositions (the model of single-atom steps: Al steps or O steps).

How Escherichia coli lands and forms cell clusters on a surface: a new role of surface topography

Bacterial response to surface topography during biofilm formation was studied using 5 μm tall line patterns of poly (dimethylsiloxane) (PDMS). Escherichia coli cells attached on top of protruding line patterns were found to align more perpendicularly to the orientation of line patterns when the pattern narrowed. Consistently, cell cluster formation per unit area on 5 μm wide line patterns was reduced by 14-fold compared to flat PDMS. Contrasting the reduced colony formation, cells attached on narrow patterns were longer and had higher transcriptional activities, suggesting that such unfavorable topography may present a stress to attached cells. Results of mutant studies indicate that flagellar motility is involved in the observed preference in cell orientation on narrow patterns, which was corroborated by the changes in cell rotation pattern before settling on different surface topographies. These findings led to a set of new design principles for creating antifouling topographies, which was validated using 10 μm tall hexagonal patterns.

The importance of 2D aggregates on the antimicrobial resistance of Staphylococcus aureus sessile bacteria

Biofilms formed on implanted devices are difficult to eradicate. Adhesion mechanism, high bacterial density, aggregation, induction of persisters and stressed bacteria are some of the factors considered when the antimicrobial resistance of these biofilms is analyzed. The aim of this work was to provide an alternative approach to the understanding of this issue by using a specially designed experimental set up that includes the use of microstructured (MS) surfaces (potential inhibitors of bacterial aggregation) in combination with antimicrobial agents (streptomycin and levofloxacin) against Staphylococcusaureus attached cells. Biofilms formed on smooth surfaces were used as plain controls (biofilmed-PC) characterized by the formation of dense 2D bacterial aggregates. Results showed bacterial persistence when streptomycin or levofloxacin were applied to PC-biofilms. The antimicrobial activity of both antibiotics was enhanced when bacteria were attached on MS, where single cells or small aggregates were observed. Thus, dense 2D aggregates of bacteria seem to be crucial as a required previous stage to develop the antimicrobial resistance.

Modulating particle adhesion with micro-patterned surfaces

We report the first experimental study on the modulation of adhesion force distribution by surface micro-patterns and its impact on particle attachment. The effect of substratum topography on particle adhesion was evaluated using well-defined microscopic surface patterns consisting of orthogonal arrays of cuboid pillars or pits with different sizes and spacing fabricated by the conventional photolithography and reactive ion etching (RIE). Adhesion of carboxyl modified poly(styrene-co-acrylic-acid) particles of 6 μm in diameter under favorable deposition conditions was found to be markedly lower on all the micro-patterned surfaces compared with that on the smooth control surface, and particle adhesion depended on the characteristic dimensions of the surface micro-structures relative to the particle size. Particle adhesion was minimal when the pillar cross-sectional dimension was below a critical value close to the diameter of the particle while the spacing between pillars was less important. Meanwhile, particles adhered displayed unique distribution on the micro-patterned surfaces. The majority of particles preferentially adhered on or close to the edge of the pillars (in the valley). Atomic force microscopy measurements using a colloidal probe revealed that the surface features strongly modulated the spatial and probability distribution of adhesion forces on the micro-patterned surfaces. Micro-sized pillars changed the adhesion force probability distribution from monomodal to bimodal, with significantly reduced maximum adhesion force. This was hypothesized to be responsible for the reduced total particle adhesion.

Structure-related antibacterial activity of a titanium nanostructured surface fabricated by glancing angle sputter deposition

The aim of this study was to reproduce the physico-mechanical antibacterial effect of the nanocolumnar cicada wing surface for metallic biomaterials by fabrication of titanium (Ti) nanocolumnar surfaces using glancing angle sputter deposition (GLAD). Nanocolumnar Ti thin films were fabricated by GLAD on silicon substrates. S. aureus as well as E. coli were incubated with nanostructured or reference dense Ti thin film test samples for one or three hours at 37 °C. Bacterial adherence, morphology, and viability were analyzed by fluorescence staining and scanning electron microscopy and compared to human mesenchymal stem cells (hMSCs).Bacterial adherence was not significantly different after short (1 h) incubation on the dense or the nanostructured Ti surface. In contrast to S. aureus the viability of E. coli was significantly decreased after 3 h on the nanostructured film compared to the dense film and was accompanied by an irregular morphology and a cell wall deformation. Cell adherence, spreading and viability of hMSCs were not altered on the nanostructured surface. The results show that the selective antibacterial effect of the cicada wing could be transferred to a nanostructured metallic biomaterial by mimicking the natural nanocolumnar topography.

Novel materials for biofilm reactors and their characterization

The application of adherently growing microorganisms for biotechnological production processes is established, but it is still a niche technology with only a small economic impact. However, novel approaches are under development for new types of biofilm reactors. In this context, increasingly more microstructured metal surfaces are being investigated, and they show positive effects on the bacterial growth and the biofilm establishment. However, for comparison of the data, the different surface materials have to correspond in their different characteristics, such as wettability and chemical composition. Also, new materials, such as plastic composite supports, were developed. To understand the interaction between these new materials and the biofilm-producing microorganisms, different surface science methods have to be applied to reveal a detailed knowledge of the surface characteristics. In conclusion, microstructured surfaces show a high potential for enhanced biofilm growth, probably accompanied by an enhanced productivity of the microorganisms.

The influence of antiscalants on biofouling of RO membranes in seawater desalination

Antiscalants are surface active polyelectrolyte compounds commonly used in reverse osmosis (RO) desalination processes to avoid membrane scaling. In spite of the significant roles of antiscalants in preventing membrane scaling, they are prone to enhance biofilm growth on RO membranes by either altering membrane surface properties or by serving as nutritional source for microorganisms. In this study, the contribution of antiscalants to membrane biofouling in seawater desalination was investigated. The effects of two commonly used antiscalants, polyphosphonate- and polyacrylate-based, were tested. The effects of RO membrane (DOW-Filmtec SW30 HRLE-400) exposure to antiscalants on its physico-chemical properties were studied, including the consequent effects on initial deposition and growth of the sessile microorganisms on the RO membrane surface. The effects of antiscalants on membrane physico-chemical properties were investigated by filtration of seawater supplemented with the antiscalants through flat-sheet RO membrane and changes in surface zeta potential and hydrophobicity were delineated. Adsorption of antiscalants to polyamide surfaces simulating RO membrane's polyamide layer and their effects on the consequent bacterial adhesion was tested using a quartz crystal microbalance with dissipation monitoring technology (QCM-D) and direct fluorescent microscopy. A significant increase in biofilm formation rate on RO membranes surface was observed in the presence of both types of antiscalants. Polyacrylate-based antiscalant was shown to enhance initial cell attachment as observed with the QCM-D and a parallel plate flow cell, due to rendering the polyamide surface more hydrophobic. Polyphosphonate-based antiscalants also increased biofilm formation rate, most likely by serving as an additional source of phosphorous to the seawater microbial population. A thicker biofilm layer was formed on the RO membrane when the polyacrylate-based antiscalant was used. Following these results, a wise selection of antiscalants for scaling control should take into account their contribution to membrane biofouling propensity.

Selective bactericidal activity of nanopatterned superhydrophobic cicada Psaltoda claripennis wing surfaces

The nanopattern on the surface of Clanger cicada (Psaltoda claripennis) wings represents the first example of a new class of biomaterials that can kill bacteria on contact based solely on its physical surface structure. As such, they provide a model for the development of novel functional surfaces that possess an increased resistance to bacterial contamination and infection. Their effectiveness against a wide spectrum of bacteria, however, is yet to be established. Here, the bactericidal properties of the wings were tested against several bacterial species, possessing a range of combinations of morphology and cell wall type. The tested species were primarily pathogens, and included Bacillus subtilis, Branhamella catarrhalis, Escherichia coli, Planococcus maritimus, Pseudomonas aeruginosa, Pseudomonas fluorescens, and Staphylococcus aureus. The wings were found to consistently kill Gram-negative cells (i.e., B. catarrhalis, E. coli, P. aeruginosa, and P. fluorescens), while Gram-positive cells (B. subtilis, P. maritimus, and S. aureus) remained resistant. The morphology of the cells did not appear to play any role in determining cell susceptibility. The bactericidal activity of the wing was also found to be quite efficient; 6.1 ± 1.5 × 10(6) P. aeruginosa cells in suspension were inactivated per square centimeter of wing surface after 30-min incubation. These findings demonstrate the potential for the development of selective bactericidal surfaces incorporating cicada wing nanopatterns into the design.

Surface topographical factors influencing bacterial attachment

Substratum surface roughness is known to be one of the key factors in determining the extent of bacterial colonization. Understanding the way by which the substratum topography, especially at the nanoscale, mediates bacterial attachment remains ambiguous at best, despite the volume of work available on the topic. This is because the vast majority of bacterial attachment studies do not perform comprehensive topographical characterization analyses, and typically consider roughness parameters that describe only one aspect of the surface topography. The most commonly reported surface roughness parameters are average and root mean square (RMS) roughness (R(a) and R(q) respectively), which are both measures of the typical height variation of the surface. They offer no insights into the spatial distribution or shape of the surface features. Here, a brief overview of the current state of research on topography-mediated bacterial adhesion is presented, as well as an outline of the suite of roughness characterization parameters that are available for the comprehensive description of the surface architecture of a substratum. Finally, a set of topographical parameters is proposed as a new standard for surface roughness characterization in bacterial adhesion studies to improve the likelihood of identifying direct relationships between substratum topography and the extent of bacterial adhesion.

Chlorhexidine delivery system from titanium/polybenzyl acrylate coating: evaluation of cytotoxicity and early bacterial adhesion

OBJECTIVES

The formation of biofilms on titanium dental implants is one of the main causes of failure of these devices. Streptococci are considered early colonizers that alter local environment favouring growing conditions for other colonizers. Chlorhexidine (CHX) is so far the most effective antimicrobial treatment against a wide variety of Gram-positive and Gram-negative organisms as well as fungi. This study was designed to develop a CHX delivery system appropriate for healing caps and abutments, with suitable drug release rate, effective as antimicrobial agent, and free of cytotoxic effects.

METHODS

Polybenzyl acrylate (PBA) coatings with and without CHX (Ti/PBA and Ti/PBA-CHX, respectively) and different drug loads (0.35, 0.70, and 1.40%, w/w) were assayed. The cytotoxic effect of CHX released from the different substrates on UMR106 cells was tested by alkaline phosphatase specific activity (ALP), and microscopic evaluation of the cells. Non-cytotoxic drug load (0.35%, w/w) was selected to evaluate the antimicrobial effectiveness of the system using a microbial consortium of Streptococcus species.

RESULTS

The kinetic profile of CHX delivered by Ti/PBA-CHX showed an initial fast release rate followed by a monotonic increase of delivered mass over 48 h. The number of attached bacteria decreased in the following order: Ti>Ti/PBA>Ti/PBA-0.35.

CONCLUSIONS

PBA-0.35 coating is effective to inhibit the adhesion of early colonizers on Ti without any cytotoxic effect on UMR-106 cells.

Do bacteria differentiate between degrees of nanoscale surface roughness?

Whereas the employment of nanotechnology in electronics and optics engineering is relatively well established, the use of nanostructured materials in medicine and biology is undoubtedly novel. Certain nanoscale surface phenomena are being exploited to promote or prevent the attachment of living cells. However, as yet, it has not been possible to develop methods that completely prevent cells from attaching to solid surfaces, since the mechanisms by which living cells interact with the nanoscale surface characteristics of these substrates are still poorly understood. Recently, novel and advanced surface characterisation techniques have been developed that allow the precise molecular and atomic scale characterisation of both living cells and the solid surfaces to which they attach. Given this additional capability, it may now be possible to define boundaries, or minimum dimensions, at which a surface feature can exert influence over an attaching living organism.This review explores the current research on the interaction of living cells with both native and nanostructured surfaces, and the role that these surface properties play in the different stages of cell attachment.

Bacterial attachment to RO membranes surface-modified by concentration-polarization-enhanced graft polymerization

Concentration polarization-enhanced radical graft polymerization, a facile surface modification technique, was examined as an approach to reduce bacterial deposition onto RO membranes and thus contribute to mitigation of biofouling. For this purpose an RO membrane ESPA-1 was surface-grafted with a zwitterionic and negatively and positively charged monomers. The low monomer concentrations and low degrees of grafting employed in modifications moderately reduced flux (by 20-40%) and did not affect salt rejection, yet produced substantial changes in surface chemistry, charge and hydrophilicity. The propensity to bacterial attachment of original and modified membranes was assessed using bacterial deposition tests carried out in a parallel plate flow setup using a fluorescent strain of Pseudomonas fluorescens. Compared to unmodified ESPA-1 the deposition (mass transfer) coefficient was significantly increased for modification with the positively charged monomer. On the other hand, a substantial reduction in bacterial deposition rates was observed for membranes modified with zwitterionic monomer and, still more, with very hydrophilic negatively charged monomers. This trend is well explained by the effects of surface charge (as measured by ζ-potential) and hydrophilicity (contact angle). It also well correlated with force distance measurements by AFM using surrogate spherical probes with a negative surface charge mimicking the bacterial surface. The positively charged surface showed a strong hysteresis with a large adhesion force, which was weaker for unmodified ESPA-1 and still weaker for zwitterionic surface, while negatively charged surface showed a long-range repulsion and negligible hysteresis. These results demonstrate the potential of using the proposed surface- modification approach for varying surface characteristics, charge and hydrophilicity, and thus minimizing bacterial deposition and potentially reducing propensity biofouling.