Structural improvement of CaFe₂O₄ by metal doping toward enhanced cathodic photocurrent

A phase transition-induced photocathodic p-CuFeO2 nanocolumnar film by reactive ballistic deposition

Vertical nanocolumnar Cu–Fe–O electrodes synthesized by the reactive ballistic deposition technique followed by heat treatment in an Ar atmosphere undergo a switch for conductivity at elevated temperatures.

A Metastable p-Type Semiconductor as a Defect-Tolerant Photoelectrode

A p-type Cu3Ta7O19 semiconductor was synthesized using a CuCl flux-based approach and investigated for its crystalline structure and photoelectrochemical properties. The semiconductor was found to be metastable, i.e., thermodynamically unstable, and to slowly oxidize at its surfaces upon heating in air, yielding CuO as nano-sized islands. However, the bulk crystalline structure was maintained, with up to 50% Cu(I)-vacancies and a concomitant oxidation of the Cu(I) to Cu(II) cations within the structure. Thermogravimetric and magnetic susceptibility measurements showed the formation of increasing amounts of Cu(II) cations, according to the following reaction: Cu3Ta7O19 + x/2 O2 → Cu(3-x)Ta7O19 + x CuO (surface) (x = 0 to ~0.8). With minor amounts of surface oxidation, the cathodic photocurrents of the polycrystalline films increase significantly, from <0.1 mA cm-2 up to >0.5 mA cm-2, under visible-light irradiation (pH = 6.3; irradiant powder density of ~500 mW cm-2) at an applied bias of -0.6 V vs. SCE. Electronic structure calculations revealed that its defect tolerance arises from the antibonding nature of its valence band edge, with the formation of defect states in resonance with the valence band, rather than as mid-gap states that function as recombination centers. Thus, the metastable Cu(I)-containing semiconductor was demonstrated to possess a high defect tolerance, which facilitates its high cathodic photocurrents.

Spinel ferrites (MFe2O4): Synthesis, improvement and catalytic application in environment and energy field

To develop efficient catalysts is one of the major ways to solve the energy and environmental problems. Spinel ferrites, with the general chemical formula of MFe₂O₄ (where M = Mg²⁺, Co²⁺, Ni²⁺, Zn²⁺, Fe²⁺, Mn²⁺, etc.), have attracted considerable attention in catalytic research. The flexible position and valence variability of metal cations endow spinel ferrites with diverse physicochemical properties, such as abundant surface active sites, high catalytic activity and easy to be modified. Meanwhile, their unique advantages in regenerating and recycling on account of the magnetic performances facilitate their practical application potential. Herein, the conventional as well as green chemistry synthesis of spinel ferrites is reviewed. Most importantly, the critical pathways to improve the catalytic performance are discussed in detail, mainly covering selective doping, site substitution, structure reversal, defect introduction and coupled composites. Furthermore, the catalytic applications of spinel ferrites and their derivative composites are exclusively reviewed, including Fenton-type catalysis, photocatalysis, electrocatalysis and photoelectro-chemical catalysis. In addition, some vital remarks, including toxicity, recovery and reuse, are also covered. Future applications of spinel ferrites are envisioned focusing on environmental and energy issues, which will be pushed by the development of precise synthesis, skilled modification and advanced characterization along with emerging theoretical calculation.

Recent Advancements and Future Prospects in Ultrathin 2D Semiconductor-Based Photocatalysts for Water Splitting

Ultrathin two-dimensional (2D) semiconductor-mediated photocatalysts have shown their compelling potential and have arguably received tremendous attention in photocatalysis because of their superior thickness-dependent physical, chemical, mechanical and optical properties. Although numerous comprehensions about 2D semiconductor photocatalysts have been amassed up to now, low cost efficiency, degradation, kinetics of charge transfer along with recycling are still the big challenges to realize a wide application of 2D semiconductor-based photocatalysis. At present, most photocatalysts still need rare or expensive noble metals to improve the photocatalytic activity, which inhibits their commercial-scale application extremely. Thus, developing less costly, earth-abundant semiconductor-based photocatalysts with efficient conversion of sunlight energy remains the primary challenge. In this review, it begins with a brief description of the general mechanism of overall photocatalytic water splitting. Then a concise overview of different types of 2D semiconductor-mediated photocatalysts is given to figure out the advantages and disadvantages for mentioned semiconductor-based photocatalysis, including the structural property and stability, synthesize method, electrochemical property and optical properties for H2/O2 production half reaction along with overall water splitting. Finally, we conclude this review with a perspective, marked on some remaining challenges and new directions of 2D semiconductor-mediated photocatalysts.

The structure and photoelectrochemical activity of Cr-doped PbS thin films grown by chemical bath deposition

Nanocrystalline undoped and Cr-doped PbS thin films were prepared on glass substrates by a simple chemical bath deposition method. The X-ray diffraction analyses of the films showed their polycrystalline nature with cubic structure and preferential growth along the (111) orientation. Cr incorporation decreases the average PbS crystallite size from 59.97 to 37.59 nm, whereas the strain and dislocation density showed an increasing trend. The atomic ratio of doping for Cr is about 0.63, 1.75, and 4.70% according to energy-dispersive X-ray (EDX) spectroscopy. Morphological analysis showed that the average sizes of nanoclusters decreased from 73 to 41 nm as the Cr concentration increased. The optical band gap values are increased with increasing Cr doping. The photoelectrochemical (PEC) behaviors and the stability of the Cr doped PbS photoelectrodes were studied in 0.3 M Na₂SO₃ electrolyte solution. Also, the incident photon-to-current efficiency and applied bias photon-to-current efficiency are calculated and showed optimized values of 13.5% and 1.44% at 0.68 V and 390 nm. Moreover, the optimized electrode shows high chemical stability and a long lifetime. Finally, the effect of temperature on the PEC behaviors is evaluated and the different thermodynamic parameters are calculated.

Nanocrystalline undoped and Cr-doped PbS thin films were prepared on glass substrates by a simple chemical bath deposition method as photoelectrodes for solar water splitting.

Photoelectrochemical water-splitting over a surface modified p-type Cr2O3 photocathode

H₂ generation via solar photoelectrochemical water-splitting by Cr₂O₃ was successfully realized by surface modification with TiO₂ and the following Pt deposition.

Enhanced photoelectrochemical water splitting activity of carbon nanotubes@TiO2 nanoribbons in different electrolytes

Hydrogen production from water splitting by a photocatalytic process is one way that can be used to solve global problems related to energy depletion and environmental pollution. This work aims to design and characterize a novel photocatalyst nanohybrid carbon nanotubes@TiO₂ nanoribbons (CNTs@TNRs) for enhanced photoelectrochemical (PEC) water splitting in different electrolytes under visible light irradiance. Here, hydrothermal and chemical vapor deposition (HT-CVD) were combined to grow CNTs @ the nanopits of TNRs producing network of nanohybrid CNTs@TNRs. The structural, morphological, optical, and photocatylatic properties of the TNRs and CNTs@TNRs nanohybrid were characterized by different techniques. The crystallite size is increased from 14.86 nm for TNRs to 21.61 nm for CNTs@TNRs nanohybrid. The CNTs@TNRs nanohybrid has well-resolved nanopits on the surface of the TNRs with an average diameter of 10 nm. The absorption edge of CNTs@TNRs relative to TNRs was strongly shifted to the visible light region. The band gap values are 3.78 and 2.07 eV for TNRs and CNTs@TNRs, respectively. The TNRs and CNTs@TNRs were used for the photocatalytic water splitting under visible light irradiance in Na₂S₂O₃, HCl and KOH electrolytes of different concentrations. The calculated incident photon-to-current conversion efficiency (IPCE) was 97% at 510 nm. These values are higher than those previously reported for different photoelectrodes. The number of hydrogen moles was calculated to be 300 μmol h^-1 cm^-2. Therefore, our work demonstrates a feasible route for efficient PEC water splitting under sunlight irradiation utilizing the novel CNTs@TNRs photocatalyst.

Perspectives on the Development of Oxide-Based Photocathodes for Solar Fuel Production

Photoelectrochemical cells (PECs), which use semiconductor electrodes (photoelectrodes) to absorb solar energy and perform chemical reactions, constitute one of the most attractive strategies to produce chemical fuels using renewable energy sources. Oxide-based photoelectrodes specifically have been intensively investigated for the construction of PECs due to their relatively inexpensive processing costs and better stability in aqueous media compared with other types of photoelectrodes. Although there have been many advancements in the development of oxide-based photoanodes, our understanding of oxide-based photocathodes remains limited. The goal of this Perspective is to examine the recent progress made in the field of oxide-based photocathodes and discuss future research directions. The photocathode systems considered here include binary and ternary Cu-based photocathodes and ternary Fe-based photocathodes. We assessed the characteristics and major advantages and drawbacks of each system and identified the most critical research gaps. The insights and discussions provided in this Perspective will serve as useful resources for the design of future studies, leading to the development of more efficient and practical PECs.

Directly Photoexcited Oxides for Photoelectrochemical Water Splitting

Artificial photosynthesis promises to become a sustainable way to harvest solar energy and store it in chemical fuels by means of photoelectrochemical (PEC) cells. Although it is intriguing to shift the fossil-fuel-based economy to a renewable carbon-neutral one, which will alleviate environmental problems, there is still a long way to go before it rivals traditional energy sources. Existing solar water-splitting devices can be sorted into three categories: photovoltaic-powered electrolysis, PEC water splitting, and photocatalysis (PC). PEC and PC systems hold the potential to further reduce the cost of devices due to their simple structures in which photoabsorbers and catalysts are closely integrated. PC is expected to be the least expensive approach; however, additional costs and concerns are brought about by the subsequent explosive gas separation. At the heart of all devices, semiconductor photoabsorbers should be efficient, robust, and cheap to satisfy the strict requirements on the market. Therefore, this Review intends to give readers an overview on PEC water splitting, with an emphasis on oxide material-based devices, which hold the potential to support global-scale production in the future.

Recent Advances in Earth-Abundant Photocathodes for Photoelectrochemical Water Splitting

The conversion of solar energy into hydrogen through photoelectrochemical (PEC) water splitting is an attractive way to store renewable energy. Despite the intriguing concept of solar hydrogen production, efficient PEC devices based on earth-abundant semiconductors should be realized to compete economically with conventional steam reforming processes. Herein, recent milestones in photocathode development for PEC water splitting, particularly in earth-abundant semiconductors, in terms of new techniques for enhancing performance, as well as theoretical aspects, are highlighted. In addition, recent research into newly emerging low-cost p-type semiconductors in the PEC field, such as Cu₂ BaSn(S,Se)₄ and Sb₂ Se₃ , are scrutinized and the advantages and disadvantages of each material assessed.

Photoelectrochemical Water Splitting with p-Type Metal Oxide Semiconductor Photocathodes

Photoelectrochemical (PEC) water splitting is a promising way to produce clean and sustainable hydrogen fuel. Solar hydrogen production by using p-type metal oxide semiconductor photocathodes has not been studied as extensively as that with n-type metal oxide semiconductor photoanodes and p-type photovoltaic-grade non-oxide semiconductor photocathodes. Copper-based oxide photocathodes show relatively good conductivity, but suffer from instability in aqueous solution under illumination, whereas iron-based metal oxide photocathodes demonstrate more stable PEC performance but have problems in charge separation and transport. Herein, an overview of recent progress in p-type metal oxide-based photocathodes for PEC water reduction is provided. Although these materials have not been fully developed to reach their potential performance, the challenges involved have been identified and strategies to overcome these limitations have been proposed. Future research in this field should address these issues and challenges in addition to the discovery of new materials.

Strategies for enhancing the photocurrent, photovoltage, and stability of photoelectrodes for photoelectrochemical water splitting

In this review, we survey recent strategies for photoelectrode optimization and advanced characterization methods towards efficient water splitting cells via feedback from these characterization methods.

Investigation of the Preferential Doping Site and Regulating on the Visible Light Response and Redox Performance for Fe- and/or La-Doped InNbO4

The preferential doping site, visible light response, and redox potential of Fe- and/or La-doped InNbO₄ (INO) were investigated using first-principles density functional theory. Eight designed doping models, including Fe and/or La doping at In or/and Nb sites of INO are constructed, respectively. It was found that Fe-doping and Fe,La-codoping to substitute In into an INO cell are energetically favorable, confirming that the steric hindrance plays a vital role for the selective doping site than the charge of the dopants. Fe doping always formed two impurity bands between the conduction and valence bands, originated from Fe 3d state, inferring the well visible light response. Furthermore, the presence of La has a specific regulation effects for Fe doping although the energy levels of the single La-doped models were completely similar to those of the undoped INO. The electron exchange between La and Fe dopants results in the significant interaction for codoping INO. Importantly, by doping La into INO cell, the redox potentials of Fe-doped INO could be well-regulated. The band potential moved to the more positive energy level of the models Fe-doped at Nb sites, while it shifted to the more negative level if Fe was doped at In site of La-INO. The present investigation may provide the guidance for the designative dopants to construct the photocatalyst with stable, visible response, and good redox performance.

Porous CaFe2O4 as a promising lithium ion battery anode: a trade-off between high capacity and long-term stability

Metal oxides are considered as attractive candidates as anode materials for lithium ion batteries (LIBs) due to their high capacities compared to commercialized graphite. However, fast capacity fading, which is caused by inherent large volume expansions and agglomeration of active particles upon cycling, is a great challenge. Herein, we propose the design of porous CaFe2O4 electrode material to address the above issue. Compared to pristine iron oxides, CaFe2O4 exhibits a distinct trade-off in terms of high capacity and long-term stability, which is beneficial to the potential practical applications. Such a trade-off effect is attributed to the synergistic effect between the porous structure and the in situ formed CaO nanograins during charging/discharging processes. This work provides an effective strategy in achieving anode materials with high capacity and long-term stability for next-generation LIBs.

A new electrochemical sensor for highly sensitive and selective detection of nitrite in food samples based on sonochemical synthesized Calcium Ferrite (CaFe2O4) clusters modified screen printed carbon electrode

Herein, we report a novel, disposable electrochemical sensor for the detection of nitrite ions in food samples based on the sonochemical synthesized orthorhombic CaFe₂O₄ (CFO) clusters modified screen printed electrode. As synthesized CFO clusters were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transformer infrared spectroscopy (FT-IR), Thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and amperometry (i-t). Under optimal condition, the CFO modified electrode displayed a rapid current response to nitrite, a linear response range from 0.016 to 1921 µM associated with a low detection limit 6.6 nM. The suggested sensor also showed the excellent sensitivity of 3.712 μA μM^-1 cm^-2. Furthermore, a good reproducibility, long-term stability and excellent selectivity were also attained on the proposed sensor. In addition, the practical applicability of the sensor was investigated via meat samples, tap water and drinking water, and showed desirable recovery rate, representing its possibilities for practical application.

Smoothing the single-crystal to single-crystal conversions of a two-dimensional metal–organic framework via the hetero-metal doping of the linear trimetallic secondary building unit

Doping of Co²⁺ in the linear Cd₃ cluster secondary building units lowers the single-crystal to single-crystal conversion reactivity of the resulting metal–organic framework.