Pt- and Ru-doped SnO₂-Sb anodes with high stability in alkaline medium

Treatment of Organics in Wastewater Using Electrogenerated Gaseous Oxidants

This work focuses on the comparison of the performance of direct electrochemical oxidation with indirect electrolysis mediated by gaseous oxidants in the treatment of diluted wastewater. To do this, energy consumptions of the electrolysis using mixed metal oxide (MMO) electrodes are compared with those required for the production and use of chlorine dioxide in the degradation of methomyl contained in aqueous solutions. Results demonstrate the feasibility of the mediated oxidation process and that this process is competitive with direct oxidation. The oxidants are produced under optimized conditions using the same anodic material applied for the direct degradation of organics, thus avoiding efficiency losses associated with mass transfer limitations in the degradation of dilute organic solutions. Thus, using the ClO2 gaseous oxidant, a concentration of 0.1 mM of methomyl from a solution containing 500 mL is completely removed with an energy consumption as low as 50 Wh. The application of the same energy to a direct electrolytic process for treating the same wastewater can only reach less than half of this removal. These findings may have a very important application in the use of electrochemical technology to achieve the remediation of persistent pollutants in wastewater, where their low concentrations typically make direct processes very inefficient.

One-step synthesis of Pt-Nd co-doped Ti/SnO2-Sb nanosphere electrodes used to degrade nitrobenzene

Ti/SnO2-Sb electrodes possess high catalytic activity and efficiently degrade nitrobenzene (NB); however, their low service life limits their wide application. In this study, we used one-step hydrothermal synthesis to successfully prepare Pt-Nd co-doped Ti/SnO2-Sb nanosphere electrodes. Scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy were applied to characterize the surface morphology, microstructure, and chemical composition of the electrodes, respectively. The electrochemical activity and stability of the electrodes were characterized via linear sweep and cyclic voltammetry, electrochemical impedance spectroscopy, and an accelerated service life test; their performance for NB degradation was also studied. An appropriate amount of Pt-Nd co-doping refined the average grain size of SnO2 and formed a uniform and compact coating on the electrode surface. The oxygen evolution potential, total voltammetric charge, and electron transfer resistance of the Ti/SnO2-Sb-Nd-Pt electrodes were 1.88 V, 3.77 mC/cm2, and 11.50 Ω, respectively. Hydroxy radical was the main active radical species during the electrolytic degradation of nitrobenzene with Ti/SnO2-Sb-Nd-Pt. After Pt-Nd co-doping, the accelerated service life of the electrodes was extended from 8.0 min to 78.2 h (500 mA/cm2); although the NB degradation rate decreased from 94.1 to 80.6%, the total amount of theoretical catalytic degradation of NB in the effective working time increased from 17.4 to 8754.1 mg/cm2. These findings reveal good application potential for the electrodes and provide a reference for developing efficient and stable electrode materials.

Anodic abatement of glyphosate on Pt-doped SnO2-Sb electrodes promoted by pollutant-dopant electrocatalytic interactions

The development of non-expensive and efficient technologies for the elimination of Glyphosate (GLP) in water is of great interest for society today. Here we explore novel electrocatalytic effects to boost the anodic oxidation of GLP on Pt-doped (3-13met%) SnO2-Sb electrodes. The study reveals the formation of well disperse Pt nanophases in SnO2-Sb that electrocatalyze GLP elimination. Cyclic voltammetry and in-situ spectroelectrochemical FTIR analysis evidence carboxylate-mediated Pt-GLP electrocatalytic interactions to promote oxidation and mineralization of this herbicide. Interestingly, under electrolytic conditions Pt effects are proposed to synergistically cooperate with hydroxyl radicals in GLP oxidation. Furthermore, the formation of by-products has been followed by different techniques, and the studied electrodes are compared to commercial Si/BDD and Ti/Pt anodes and tested for a real GLP commercial product. Results show that, although BDD is the most effective anode, the SnO2-Sb electrode with a 13 met% Pt can mineralize GLP with lower energy consumption.

Electrochemical degradation of methylene blue by Pb modified porous SnO2 anode

A significant number of pollutants in wastewater can be electrocatalytically oxidized by SnO₂-Sb, a relatively inactive electrode. However, the arduous process of environmental remediation due to poor electrochemical performance and short service life of the traditional Ti/SnO₂-Sb electrode. In this work the SnO₂ electrode with a micron-sized sphere structure was prepared by in-situ hydrothermal. The results of the study that the electrode (Pb-10%) synthesized from the precursor solution in which the Pb:Sn molar ratio is 10% exhibits excellent electrooxidation properties. Impressiveing, the Pb-10% electrode displayed the small charge transfer resistance (10.71 Ω) and the high oxygen evolution potential (2.26 V vs. SCE). Thus, the electrochemical degradation experiment demonstrates that 100 mg L^-1 MB was degraded by Pb-10% electrode under the condition of initial pH = 5, and the decolorization rate reached 94.6%. Moreover, the influence of different parameters such as Pb doping amount, initial pH value of solution, initial concentration of MB and inorganic ions on degradation efficiency were also explored, in turn the practical application of electrodes in the field of purifying water resources is optimized. It is worth noting that the service life of the optimized electrode (100 mA cm^-2, 0.5 M H₂SO₄, 90 h) is about 12 times longer than that of the bare electrode (Sn-Sb). Therefore, the high-performance Ti/SnO₂-Sb electrode prepared in this work possesses vast application prospects in the electrocatalytic oxidation.

Toward efficient electrocatalytic degradation of iohexol using active anodes: A laser-made versus commercial anodes

The X-ray iodinated contrast medium iohexol is frequently detected in aquatic environments due to its high persistence and the inefficiency of its degradation by conventional wastewater treatments. Hence, the challenge faced in this study is the development of an alternative electrochemical treatment using active anodes. We investigate the oxidation of iohexol (16.42 mg L^-1) using different operating conditions, focusing on the role of different mixed metal oxide anodes in the treatment efficiency. The electrocatalytic efficiency of the Ti/RuO₂-TiO₂ anode prepared using a CO₂ laser heating and an ionic liquid is compared with Ti/RuO₂-TiO₂-IrO₂ and Ti/IrO₂-Ta₂O₅ commercial anodes. The hypochlorite ions generated by the anodes are also analyzed. The effect of the electrolyte composition (NaCl, Na₂SO₄, and NaClO₄) and current density (15, 30, and 50 mA cm^-2) on the iohexol degradation is also studied. The Ti/RuO₂-TiO₂ laser-made anode is more efficient than the commercial anodes. After optimizing experimental parameters, this anode removes 95.5% of iohexol in 60 min and displays the highest kinetic rate (0.059 min^-1) with the lowest energy consumption per order (0.21 kWh m^-3order^-1), using NaCl solution as the electrolyte and applying 15 mA cm^-2. Additionally, iohexol-intensified groundwater was used to compare the efficiency of anodes. The Ti/RuO₂-TiO₂ is also more efficient in removing the organic charge from the real water matrix (21.7% TOC) than the commercial anodes. Notably, the iohexol removal achieved is higher than all electrochemical treatments already reported using state-of-the-art non-active anodes in lower electrolysis time. Therefore, data from this study indicate that the electrochemical degradation of iohexol using the Ti/RuO₂-TiO₂ anode is efficient and has excellent cost-effectiveness; thus, it is a promising approach in the degradation of iohexol from wastewater. Furthermore, the Ti/RuO₂-TiO₂ active anode is competitive and can be an excellent option for treating effluents contaminated with recalcitrant organic compounds such as iohexol.

Photoelectrocatalytic treatment of levofloxacin using Ti/MMO/ZnO electrode

Here, the antibiotic levofloxacin (LFX) widely used and detected in the environment was degraded by photoelectrolysis using a new electrode based on zinc oxide (ZnO) and a mixture of mixed oxides of ruthenium and titanium (MMO). The influence of the potential and irradiation of UV light was investigated in the photostability of the Ti/MMO/ZnO electrode and in the degradation of the antibiotic. The experiments were conducted at different pH values (5.0, 7.0 and 9.0) in sodium sulfate solution in a glass reactor with central lighting. It was observed that the new Ti/MMO/ZnO electrode has good stability under light irradiation and potential, presenting excellent photocurrent and high photoactivity in LFX photoelectrolysis. The removal efficiency of the compound was directly related to the formation of oxidizing species in solution, the photo-generated charges on the electrode and the electrostatic characteristics of the molecule. The mineralization rate, the formation of reaction intermediates and short chain carboxylic acids (acetic, maleic, oxalic and oxamic acid), in addition to the formation of N-mineral species (NO₃^- and NH₄⁺) was dependent on the pH of the solution and the investigated processes: photoelectrolysis was more efficient than photolysis, which, in turn, was more efficient than electrolysis. The synergistic effect and the high rate of degradation of LFX after 4.0 h of treatment (100%) observed in photoelectrolysis at alkaline pH, was associated with the high stability of the Ti/MMO/ZnO electrode at this pH, the photoactivation of sulfate ions and the ease generation of oxidizing radicals, such as OH.

Efficient degradation of polyacrylamide using a 3-dimensional ultra-thin SnO2-Sb coated electrode

Polyacrylamide (PAM) is widely used in polymer flooding processes to increase oil recovery while the byproduct of PAM-containing wastewater is a serious environmental issue. In this study, electrochemical oxidation process (EAOP) was applied for treating PAM wastewater using a new type of 3-dimensional ultra-thin SnO₂-Sb electrode. Nano-sized catalysts were evenly dispersed both on the surface and inside of a porous Ti filter forming nano-thickness catalytic layer that enhances the utilization and bonding of catalysts. This porous Ti electrode showed 20% improved OH· production and 16.3 times increased accelerated service life than the planar Ti electrode. Using this electrode to treat 100 mg L^-1 PAM, the TOC removal efficiency reached over 99% within 3 h under current density of 20 mA cm^-2. The EAOP could fastly break the long-chain PAM molecules into small molecular intermediates. With the porous electrode treating 5 g L^-1 PAM under current density of 30 mA cm^-2, EAOP reduced 94.2% of average molecular weight in 1 h and 92.0% of solution viscosity in 0.5 h. Moreover, the biodegradability of PAM solution was significantly improved as the solution BOD₅/COD ratio raised from 0.05 to 0.41 after 4 h treatment. The degradation pathway of PAM was also investigated.

Electrochemical degradation of chloramphenicol using Ti-based SnO2-Sb-Ni electrode

Antibiotic residues may be very harmful in aquatic environments, because of limited treatment efficiency of traditional treatment methods. An electrochemical system with a Ti-based SnO₂-Sb-Ni anode was developed to degrade a typical antibiotic chloramphenicol (CAP) in water. The electrode was prepared using a sol-gel method. The performance of electrode materials, impact factors and dynamic characteristics were evaluated. The Ti-based SnO₂-Sb-Ni electrode was compact and uniform as shown by characterization using SEM and XRD. The electrocatalytic oxidation of CAP was carried out in a single-chamber reactor by using a Ti-based SnO₂-Sb-Ni electrode. For 100 mg L^-1 CAP, the CAP removal ratio of 100% and the TOC removal ratio of 60% were obtained at the current density of 20 mA cm^-2 and in a neutral electrolyte at 300 min. Kinetic investigation has shown that the electro-oxidation of CAP on a Ti-based SnO₂-Sb-Ni electrode displayed a pseudo-first-order kinetic model. Free radical quenching experiments presented that the oxidation of CAP on Ti-based SnO₂-Sb-Ni electrode resulted from the synergistic effect of direct oxidation and indirect oxidation (·OH and ·SO₄^-). Doping Ni on the Ti/SnO₂-Sb electrode for CAP degradation was presented in this paper, showing its great application potential in the area of antibiotic and halogenated organic pollutant degradation.

Dimensionally stable Ti/SnO2-RuO2 composite electrode based highly efficient electrocatalytic degradation of industrial gallic acid effluent

In this work, dimensionally stable Ti/SnO₂-RuO₂ electrode is successfully prepared using thermal decomposition method for the electrocatalytic degradation of high-concentration industrial gallic acid (GA) effluent in detail. The surface morphology, crystal structure and element analysis of as-prepared Ti/SnO₂-RuO₂ electrode are characterized by scanning electron microscopy, X-ray diffraction and X-ray fluorescence spectrometer, respectively. In addition, cyclic voltammetry, polarization curve and accelerated life tests are exploited to investigate the electrocatalytic activity and stability of Ti/SnO₂-RuO₂ electrode. Orthogonal experiment shows that, among the factors (current density, temperature and initial pH), current density is pivotal parameter influencing the degradation efficiency of industrial GA effluent. COD removal and degradation efficiencies of GA effluent reach up to 76.9% and 80.1% after 6 h, respectively, at the optimal conditions (current density of 10 mA cm^-2, pH 6 and 35 °C). The degradation of GA effluent follows pseudo-first-order reaction kinetics. This work provides an in-depth theoretical support and application of electrocatalytic technology to the treatment of high-concentration industrial GA effluent.

High-Performance Quantum Dots with Synergistic Doping and Oxide Shell Protection Synthesized by Cation Exchange Conversion of Ternary-Composition Nanoparticles

The insertion of cation impurities into quantum dots (QDs) as a dopant has been proved to be an efficient way to tailor their optical, electronic, and magnetic properties; however, the low quantum yield (QY) and poor photostability strongly limit their further applications. We report a strategy to coat a thin oxide shell around the heterovalent doped QDs to enhance their QYs and photostabilities simultaneously. In the case of Ag⁺-doped CdS QDs, the controlled cation exchange reaction between Cd²⁺ and ternary Ag₃SbS₃ nanoparticles not only realizes the Ag⁺ doping in CdS QDs but also generates a thin Sb₂O₃ shell around the surface of the QDs. Enabled by such, as-prepared CdS:Ag@Sb₂O₃ QDs exhibited enhanced photostability and high QY of 66.5%. We envision that the findings presented here will inspire more novel protocols for advancing the practical applications of doped QDs.

Electrochemical oxidation of gaseous benzene on a Sb-SnO2/foam Ti nano-coating electrode in all-solid cell

An all-solid cell with a solid polymer electrolyte was applied to electrochemical oxidation of low-concentration indoor gaseous aromatic pollution. Antimony-doped tin dioxide nanocoatings deposited on a titanium foam substrate (Ti/Sb-SnO₂) with different Sb/Sn ratios (4.8-14.0 mol%) and loading weight of Sb-SnO₂ (4.4-7.7 mg cm^-2) were used as dimensionally stable anodes. Sn and Sb were homogeneously dispersed on the substrate, and a crack-free nanocoating was built when the loading of nanocoating was increased to 6.3 mg cm^-2. The activity tests for oxidation of benzene showed that 40 ppm gaseous benzene was converted to CO₂ with high selectivity (85%) at the low cell voltage of 2.0 V in this all-solid cell. The conversion of benzene was greatly increased from 30% to 100% upon increasing the Sb/Sn ratio of the nanocoating from 4.7 mol% to 14.0 mol%. With the increase of nanocoating loading (Sb/Sn = 14.0 mol%) from 6.3 to 7.7 mg cm^-2, the conversion of 100 ppm benzene was increased from 70% to 100%. Cyclic voltammetry revealed that high Sb content in the oxide nanocoating increased the overpotential and current intensity of the oxygen evolution reaction. The large outer charge q_o^∗ related to the electroactive surface of the SS-7.7/Ti3 electrode was up to 305.3 mC cm^-2, which were responsible for its excellent electrochemical performance in the benzene oxidation process. Our studies provide a potential method for removal of indoor VOCs at ambient temperature.

Effect of calcination temperature on the properties of Ti/SnO2-Sb anode and its performance in Ni-EDTA electrochemical degradation

Pd-doped Ti/SnO₂-Sb anode was prepared at different calcination temperatures by a wet-impregnation method and employed in simultaneous electrochemical catalytic degradation of Ni-EDTA and recovery of nickel. The results showed that Ti/SnO₂-Sb-Pd-500 could achieve the highest electrochemical activity (87.5% of Ni-EDTA removal efficiency), superior durability (50.7 h of accelerated lifetime), and higher Ni recovery (19.8%) on cathode. Cyclic voltammetry (CV) and linear sweep voltammetry (LSV) analysis suggested that Ni-EDTA degradation on anode was mainly indirect oxidation-controlled reaction, attributing to the high oxide state of MO_X + 1 and MO_X(·OH), rather than direct oxidation. Scanning electron microscope (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses indicated that calcination temperature could modify the morphology of electrode surface and affect the incorporation and valence state transformation of metal species (Sb and Pd) in SnO₂ lattice. Ti/SnO₂-Sb-Pd-500 achieved the highest electrochemical capacity with the highest levels of adsorbed oxygen O_ads/E_T (27.11%) and lattice oxygen O_lat/E_T (29.69%). Moreover, the operation conditions for Ni-EDTA electrochemical degradation were optimized. These findings were valuable for developing a high-performance electrode for Ni-EDTA electrochemical degradation.

Strong metal–support interaction improves activity and stability of Pt electrocatalysts on doped metal oxides

Niobium and antimony doped tin oxide loose-tubes decorated with Pt nanoparticles present outstanding mass activity and stability, exceeding those of a reference carbon-based electrocatalyst.

Three-dimensional ordered mesoporous Co3O4 enhanced by Pd for oxygen evolution reaction

Considerable efforts have been devoted recently to design and fabrication of high performance and low cost electrocatalysts for oxygen evolution reaction (OER). However, catalytic activity of current electrocatalysts is usually restricted by high onset potential and limited active sites. Herein, we fabricated three-dimensional (3D) highly ordered mesoporous Pd-Co₃O₄ composite materials as excellent electrocatalysts for OER in alkaline solution with high activity and stability. Three-dimensional highly ordered mesoporous Co₃O₄ material was firstly synthesized using mesoporous silica KIT-6 as hard template. Then, Pd-Co₃O₄ nanomaterials were prepared by a simple reduction method. The as-prepared 3D mesoporous Pd-Co₃O₄ catalysts have ordered mesoporous structure with a high surface area of 81.0 m² g^-1. Three-dimensional highly ordered mesoporous structure can facilitate diffusion and penetration of electrolyte and oxygen. Moreover, the catalysts can also keep catalyst particles in a well dispersed condition with more catalytic active sites. Electrochemical measurements reveal that the 3D mesoporous Pd-Co₃O₄ catalysts exhibit superior performance in alkaline solution with low onset potential (0.415 V vs. SCE) and excellent long-duration cycling stability.

Au-NiCo2O4 supported on three-dimensional hierarchical porous graphene-like material for highly effective oxygen evolution reaction

A three-dimensional hierarchical porous graphene-like (3D HPG) material was synthesized by a one-step ion-exchange/activation combination method using a cheap metal ion exchanged resin as carbon precursor. The 3D HPG material as support for Au-NiCo₂O₄ gives good activity and stability for oxygen evolution reaction (OER). The 3D HPG material is induced into NiCo₂O₄ as conductive support to increase the specific area and improve the poor conductivity of NiCo₂O₄. The activity of and stability of NiCo₂O₄ significantly are enhanced by a small amount of Au for OER. Au is a highly electronegative metal and acts as an electron adsorbate, which is believed to facilitate to generate and stabilize Co⁴⁺ and Ni³⁺ cations as the active centres for the OER.

One-pot synthesis of Zn-doped SnO2 nanosheet-based hierarchical architectures as a glycol gas sensor and photocatalyst

Zn-doped SnO₂ hierarchical architectures show high response and good selectivity to glycol and good selectivity to MB as a photocatalyst.